Interstate Batteries IB Pulse Testing Program Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

IB PULSE

TESTING PROGRAM MANUAL

Table of Contents

Troubleshooting

Need help?

Do you have a question about the IB Pulse and is the answer not in the manual?

Questions and answers

Summary of Contents for Interstate Batteries IB Pulse

Page 1 IB PULSE TESTING PROGRAM MANUAL ®...
Page 2: Table Of Contents
Wi-Fi Hub Troubleshooting Add Printer IB Pulse Deleting A Printer Front Default Printer Back Languages Navigation System Language Initial IB Pulse Power Up Test Result Language Setting User Preferences Email Language Charging Dock Print Language Front Display Side Brightness Charging Dock Mounting (Optional) Auto Brightness 2 –...
Page 3: Introduction
Description Testing Out-of-Vehicle The preferred battery test location is in the vehicle. However The IB Pulse provides a complete analysis of 12-volt and 6-volt when testing out of the vehicle: vehicle batteries and 12-volt and 24-Volt starting/charging systems. Using patented conductance technology, the IB Always disconnect the negative cable from the battery first •...
Page 4: Wi-Fi Hub
1 – Introduction IB Pulse Wi-Fi Hub The Wi-Fi Hub is required at every shop using an IB Pulse battery tester. The Hub transmits its own Wi-Fi signal and easily connects to existing Internet hardware devices. Once paired with an IB Pulse, it automatically downloads local shop information;...
Page 5: Wi-Fi Hub Installation
Delete the Wi-Fi Hub and then reconnect • Check Hub connection and setup • Ensure IB Pulse is charged at a minimum of 40% • Place IB Pulse in charging dock during update Software update doesn’t complete or IB Pulse is not connected to the Wi-Fi Hub...
Page 6: Ib Pulse
Date Time: Select the correct time zone, date, and time and > select Next The IB Pulse features a touch screen for accessing various functions NOTE: Time zone, date, and time must be cor- and options. rectly set in order for the IB Pulse to connect to  ...
Page 7: Setting User Preferences
• A confirmation message is displayed when successful. NOTE: Not all Wi-Fi and Bluetooth printers are supported by the IB Pulse. For a complete list of supported printers, go to: www.interstatebatteries.com/ibpulse Add Wi-Fi Printer (Optional Equipment): Select Yes to add.
Page 8: Charging Dock
1 – Introduction IB Pulse Charging Dock Front Side Power Supply Connection Wall Mounting Bracket Charging Dock Mounting (Optional) Release the two (2) holding tabs on the bottom of the Charg- Connect the Power Supply to the jack on the Charging Dock.
Page 9: Vin Scan In Vehicle Testing
Recommended Batteries to match and recommend batter- • ies by part number By default, the IB Pulse is configurated to test in-vehicle automotive batteries using test parameters determined by vehicle VIN or the year, make, and model of the vehicle being tested.
Page 10 > displayed keypad to manually enter the VIN. Select Next to continue. Connect the IB Pulse clamps to the battery posts and select Start. IMPORTANT: If the entered VIN is a start-stop vehicle and the IB Pulse has been paired to a IB Pulse XP module, connect the IB Pulse XP to the Y/M/M: Select to manually enter year, make, and model data.
Page 11: Battery Test Results
IB Pulse 2 – VIN Scan In Vehicle Testing Align the battery within the camera view window and hold the sensor on back of tester 6 to 12 inches from battery surface. Via email or through a configured printer. Send Results Exit the test and return to the Home Screen.
Page 12: System Test
After the System Test is initialized, start the vehicle's engine when prompted and leave it running for 15 seconds. The IB Pulse will detect the engine start and analyze the cranking voltage and time. Turn off the engine when prompted.
Page 13: Cranking Health Decisions
IB Pulse 2 – VIN Scan In Vehicle Testing Cranking Health Decisions Reset Decision Action Displays a checklist of vehicle-specific procedures to ensure the vehicle electronics are functioning Cranking Starter voltage normal & battery is fully charged. Reset properly following the installation of a new battery.
Page 14: Out Of Vehicle Test
Consider replacing the battery Soon before it is exposed to temperature extremes. Connect the IB Pulse tester clamps to the battery terminals. Charge & State of charge too low for diagnosis. Fully charge & At the Home Screen, select a User from the displayed list.
Page 15: Battery Test Results
IB Pulse 3 – Out Of Vehicle Test Battery Test Results < > to view the battery test results, cranking health, and the test record for the vehicle tested. The dots at the bottom of the results screen indicate additional screens are <...
Page 16: Menu
Cancel to exit and return to the email list. Favorites ✩ to select an email address add it as a Favorite. Select a displayed Wi-Fi Hub. The IB Pulse will automatically to deselect and remove a Favorite email address. ✩ ✩ configure the tester to the Wi-Fi Hub.
Page 17: Printers
IB Pulse 4 – Menu Printers After the IB Pulse adds the printer, it will switch back to the HUB network. The Printer Setup function detects and displays a list of NOTE: A test print can be completed by selecting connected and available Wi-Fi and Bluetooth printers.
Page 18: Display
> Select Done or Next Sleep Time Adjust the amount of elapsed time before the IB Pulse goes into The new User name is displayed on the Users screen. a power saving (Sleep) mode. Default = 2 minutes. Editing A User...
Page 19: Date Time
4 – Menu Date Time Test Settings Adjust the IB Pulse Date and Time format and the Time Set the default Test Settings for Temperature Units and Zone in which the tester will be used. The date and time Test Mode.
Page 20: About
Promotions can be setup for a specific number of displays • for each user. For example, a Promotion will display for the first five days a user logs into the IB Pulse, but still valid be- yond that time. Promotions can also be emailed or printed using a Wi-Fi •...
Page 21: Appendix
IB Pulse Appendix Appendix Battery Information Screen Descriptions Scanning Tips Barcode Scanner: Located on the back of the tester in be- • A unique code, including a serial number, used tween the clamp holsters. by the automotive industry to identify individual motor vehicles, motorcycles, scooters and mopeds, as defined in ISO 3833.
Page 22: Wi-Fi Printer Setup/Troubleshooting
IB Pulse) different Wi-Fi instructions above network to re-add the Wi-Fi printer to the IB Pulse Test records are Printer is out of paper Add paper to the not printing when paper tray successfully sent to Printer low on ink...
Page 23: Product Specifications
IB Pulse Appendix Product Specifications IB Pulse IB Pulse Includes: Pulse Tester, 3’ test cables, charging/storage dock, AC power adapter Application 6V & 12V Batteries 12V & 24V Charging/Starting System Automotive, Group 31, Lawn & Garden, Marine, Powersports, Commercial 4D/8D Batteries Rating System CCA •...
Page 24 This product is protected by one or more U.S. and foreign patents. For specific patent information contact 630.323.2800. Limited Warranty Refer to your local Interstate Batteries Distributor with questions regarding warranty. Service Contact your local Interstate Batteries Distributor for service assistance or call 877.464.3318. interstatebatteries.com/IBPulse 167-000866EN-C 1/20 ©2020 All rights reserved. IBSA NAC-994...