Summary of Contents for Sola-Tecs F Series
- Page 1 SOLA-TECS F Overview Assembly instructions BJ 2019 … SN 2917 … F2000 | F3200 | F4000 MA 0302506 R00 2019-07...
- Page 2 Component 1300 top carriage SOLA-TECS F 6.5 meters pull rope 1300 bottom carriage IQS standard sealing cap L1600 connecting tube element Tool bag L700 connecting tube element L800 connecting tube element Velcro cable ties Active end cap Passive end cap...
- Page 3 It is IMPORTANT that you read these operating instructions carefully READ CAREFULLY BEFORE USE and KEEP FOR FUTURE REFERENCE. Exagon socket - Size 5 Technical data SOLA-TECS F BJ 2019 … Exagon socket - Size 4 Seriennummer SN 2917 …...
-
Page 4: Safety Instructions
This protects you from injuries caused by the voltaic frames are particularly dirty. The spray nozzles and The SOLA-TECS F system consists of a carrier system on the brush rollers can be switched on or off independently of machine starting suddenly and accidentally. -
Page 5: Components And Their Function
The water supply is switched on and off at the water distributor. The top and bottom carriages are the drive units of the carrier system. With them, the SOLA-TECS F system can The counter bearing guides the brush roller ends up and be rolled over the photovoltaic panels. - Page 6 Velcro cable ties voltaic panels when the drive units rest on the brush stops when crossing a gap. The pull ropes are for pulling the Sola-Tecs F system over the photovoltaic panels. Together with the mounted brush rollers, the Sola-Tecs C is the cleaning/drive unit.
- Page 7 Introduction Adjusting the wheels: To adjust the wheels on the frame Parking the Sola-Tecs F: When the mounted Sola-Tecs F Wheels Parking of the photovoltaic panel, each wheel can be moved over is not required, the whole unit can be placed on the sup- the axle.
- Page 8 The mark helps to align the connecting tube horizontally. Set the travel limit and clearance of Sola-Tecs C: Travel limit / clearance of Sola-Tecs C The travel limit and clearance are set with the stop clamp. The stop clamp can be tightened and released with the screw [1].
- Page 9 [1] and [2]. The width of the brush roller Adjust the width of the brush roller: The Sola-Tecs C brush rollers are divided into segments. The individual seg- ments are connected by a thread [1][2]. The width of the cleaner can be changed by inserting or removing individual segments.
- Page 10 Construction Assembly of the Couple end caps: quired installation size. Make sure that all three connecting Risk of injury during assembly tubes are divided equally. The scale must be continuous The end caps are designed as active and passive [6]. from one connecting tube element to the next.
- Page 11 Construction Mounting the carriage [bottom] in front of the connecting tubes. Hexagon Mount VR2: Risk of injury during assembly socket 4 is required to clamp the [VR1] [VR2] connec- Insert the hexagon socket 5 into the red mark until it sits in ting tubes.
- Page 12 [VR2]. The attachments are each turned by 180°. 1. Brush stop - the brush stop is always mounted oppo- site the Sola-Tecs C. Its task is to make sure the Sola-Tecs C follows the direction of the photovoltaic panels 2. Roll holder - the roll holder supports the connecting tube.
- Page 13 Construction Assembly of the VR2: Hexagon sockets 3 and 5 are required. 5 (page 12). VR1 and VR3: Push the counter bearing to the [outside] with the arm Place the relief roller in the middle of the structural and slide it into position together with the stop clamps. Fix length and fix it with hexagon socket 5.
- Page 14 Construction Mounting the connec- After mounting the attachments, the [top] carriage must bearing. Insert the hexagon socket 4 into the red mark in the same way. Check whether the line of the scale is be mounted. Hexagon socket 4 is required to clamp the until it sits in the screw head.
- Page 15 5 mm Installation of third cleaner: In this step, the Sola-Tecs C cleaning devices are installed. from the carriage. Push the third cleaner onto the clamping element [2]. Risk of injury during assembly Hexagon socket 5 is required for this.
- Page 16 [bottom] carriage screws on the [VR1] so that the head of the Sola-Tecs C on page 10. The lever position is not yet suitable for of the lever into account, 2 cm must be subtracted from the measured rests in the fork.
- Page 17 6. The distributor tube for the Sola-Tecs C on the top carriage ≈ 150 mm until the end brush roll MA 0302506 R00 2019-07...
- Page 18 Aufbau Mounting the high- Mounting high-pressure hoses on the VR1: Mounting high-pressure hoses on the VR3: wed onto the water distributor connection [1]. The high- pressure hose is then laid under the carriage to connection The 1000 mm high-pressure hose is screwed to the water The 1000 mm high-pressure hose is screwed to the water of the first clamping element and screwed on.
- Page 19 [6]. Take the handle tube [7]. Thread into the holder [11] [12] from below. The Sola-Tecs F the carriage. Hexagon socket 6 is required for mounting. the grip tube onto the carrier tubes with the connectors can be stored ready for use with a support frame.
- Page 20 [4]. In this last assembly step, the Sola-Tecs C is set to the wheels rest on the outside of the frame. Adjust the top and working height. Hexagon socket 5 is required for this.
Need help?
Do you have a question about the F Series and is the answer not in the manual?
Questions and answers