Table of Contents
Summary of Contents for Hydralok H25ECO-QC
- Page 1 USER MANUAL H25Eco QC Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk...
-
Page 2: Table Of Contents
CALIBRATION INSTRUCTIONS ................... 12 SPARE PARTS ........................13 ELECTRICAL DIAGRAM ....................... 14 Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 3: Warranty Conditions
8. This warranty is not valid in case of unauthorised machine modification. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 4: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY H25EcoQC Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk Page.4... -
Page 5: Safety Regulations
9. Only original spare parts can be used in the maintenance of the machine. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 6: Technical/Dimensional Data
The equipment does not have its own lighting and so it must be used in a suitably illuminated area. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 7: Routine Maintenance
At the rear of the machine remove the oil filler cap and check that the oil level is between 20- 25mm from the top of the tank. Where necessary add oil (ISO 32 Hydraulic oil). Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service :... -
Page 8: Machine Description & Operating Instructions
To open the swaging head press the red opening button NB. The swaging head does not need to be fully open to release the assembly. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... - Page 9 DO NOT START THE MACHINE UNDER LOAD. ALWAYS RELEASE PRESSURE BEFORE RESTARTING. ISOLATE THE MACHINE FROM THE ELECTRICAL SUPPLY WHEN NOT IN USE. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk...
-
Page 10: Quick Change
7. Replace the dies into the correct insert in the rack, and turn off the tool. 8. Replace tool into the tool holder for safekeeping. Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 11: Die Fitting Instructions
Figure 1 below. Figure 1 CALIBRATOR Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 12: Die Chart
7. Set the calibrator to a new setting and produce a swaged assembly. 8. Check the finished swage size. (If incorrect repeat the calibration operation) Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk... -
Page 13: Spare Parts
5, 7,17,18,19,20 300-079 spring kit YA1001 calibrator assembly Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk Page. 13... -
Page 14: Electrical Diagram
ELECTRICAL DIAGRAM Machines manufactured at Hydralok, Bristol, UK Machine enquiries, sales, after sales service : Interpump Hydraulics (UK) Ltd t/a IMM Hydraulics (UK) : Kidderminster Tel : (0)121 550 1115 / sales@immhydraulics.co.uk Page.14...
Need help?
Do you have a question about the H25ECO-QC and is the answer not in the manual?
Questions and answers