Advertisement
Please read and take note of this notice before using any STATIC SWIM™ equipment.
I. INSTALLATION NOTICE FOR STATIC SWIM
INSTALLING THE « NON-SLIP LASSO ATTACHMENTAND ADJUSTABLE EXTENSION DEVICE (up to 7m) »TO A SOLID
SUPPORT
INSTALLING and ADJUSTING THE « NON-SLIP LASSO ATTACHMENT AND ADJUSTABLE EXTENSION DEVICE (up to 7m)
»
INSTALLING PEGS FOR THE STATIC SWIM™ «ADJUSTABLE POOL FLOOR ATTACHMENT DEVICE (15cm to 65cm) – HARD SURFACE POOL
DECKS»
INSTALLING PEGS FOR THE STATIC SWIM™ «ADJUSTABLE POOL FLOOR ATTACHMENT DEVICE (15cm to 65cm) – WOODEN POOL
DECKS»
ADJUSTING THE LENGTH FOR THE STATIC SWIM™ « ADJUSTABLE POOL FLOOR ATTACHMENT DEVICE (15cm to 65cm)
Installation :
1. Position de non-slip sheath around a solid support near your pool (a pillar, tree, fence etc.)
2. Put the cord through the loop.
3. Tighten around the support.
This STATIC SWIM™ attachment may also be used as an extension device when placed between
any two STATIC SWIM™ components.
Included in this kit: A non-slip sheath, a 7-m long cord, a stopper.
Installation: If necessary, adjust the length of the non-slip sheath to the width/diameter of your
support by cutting off the excess length of cord. Otherwise, use the whole length provided.
Push about 1 meter of the cord through the sheath :
1. Fold the cord about 12 cm away from the end of the sheath.
2. Tie a knot to form a 5 cm loop.
3. Now push the cord and the knot in the non-slip sheath (you may have to force it through):
Leave about 4 cm of the loop outside the sheath.
Adjusting the Length of the Cord: By positioning the stopper at the desired length, up to 7 meters
long.
Instructions:
double knot
1. Tie a
at the desired length so that the stopper is firmly in place.
2. Tighten, and cut off the excess length. Slightly heat the cut end with a lighter to avoid frayed
edges.
Included in this kit: 2 protective sheaths (0,6m each), 2 cords (1m each), 2 extendable
pegs for wooden pool floors, 6 A2 stainless steel screws, 1 stopper. INSTALLATION:
1. Drill two 12mm diameter holes, spaced 8cm apart at a suitable distance from the
edge of the pool (between 10cm and 60cm). 2. Remove all debris and residues from the
holes. 3. Gently hammer in. Hire a professional if necessary.
Included in this kit: 2 protective sheaths (0,6m each), 2 cords (1m each), 2 extendable
pegs for wooden pool floors, 6 A2 stainless steel screws, 1 stopper. INSTALLATION:
1. Drill two 12mm diameter holes, spaced 8cm apart at a suitable distance from the
edge of the pool (between 10cm and 60cm). 2. Remove all debris and residue from the
holes. 3. Drill 6 holes using a 4 mm bit (5/32). Screw. Hire a professional if necessary.
INSTALLATION NOTICE AND USER
GUIDE English/Français
EQUIPMENT
™
Advertisement
Table of Contents
Summary of Contents for Static Swim LIGHT
- Page 1 2. Tighten, and cut off the excess length. Slightly heat the cut end with a lighter to avoid frayed edges. INSTALLING PEGS FOR THE STATIC SWIM™ «ADJUSTABLE POOL FLOOR ATTACHMENT DEVICE (15cm to 65cm) – HARD SURFACE POOL DECKS» Included in this kit: 2 protective sheaths (0,6m each), 2 cords (1m each), 2 extendable pegs for wooden pool floors, 6 A2 stainless steel screws, 1 stopper.
- Page 2 To connect the STATIC SWIM™ « Adjustable Floor Attachment Device » to the retractable pegs (installed on the pool deck), simply pull up the peg and place the loops of the STATIC SWIM™ « Adjustable Floor Attachment Device » around the heads of the pegs II.
- Page 3 If necessary, replace any damaged parts of STATIC SWIM™ equipment. Only use original STATIC SWIM™ replacement parts. STATIC SWIM™ equipment does not prevent drowning. STATIC SWIM™ is not under any circumstances a floating device. 2. Guide for Training If you haven’t been physically active for a long time, it is advisable to consult your doctor before beginning training sessions.
Need help?
Do you have a question about the LIGHT and is the answer not in the manual?
Questions and answers