Summary of Contents for RIMSA PENTALED81
- Page 1 MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 1 di 19 Installation manual for surgical light system PENTALED81 ceiling mobile PENTALED105 ceiling mobile...
- Page 2 I-20831 Seregno MB Tel.: ++39 0362 325.709 Fax: ++39 0362 328.559 Email: info@rimsa.it Copyright The contents of this Manual may be amended by Rimsa, without prior notice or any further obligations, in order to make changes and improvements. The...
- Page 3 RIMSA. Right to make changes Rimsa reserves the right to change, cancel or otherwise amend the data contained in this document at any time and for any reason without prior notice inasmuch as Rimsa is constantly seeking new solutions which lead to product evolution.
-
Page 4: Table Of Contents
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 4 di 19 Table of Contents General information ..............5 1.1 Qualification of operators .............. 6 1.2 Packaging, transport, storage and characteristics of the installation site ................6 1.3 Graphic symbols used in the installation manual ......7 1.4 Graphic symbols used on the package ......... -
Page 5: General Information
NO (laughing gas) CAUTION RIMSA disclaims all liability for any injuries to persons or damage to things caused by the installation, maintenance or use of the Product by unqualified operators. By qualified operator is meant whosoever has attended a course... -
Page 6: Qualification Of Operators
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 6 di 19 CAUTION Electrical installation must be made in compliance with the IEC 60364-7-710 standard and any national regulations and must contemplate protection with fuses or thermal magnetic disconnection switch and the fitting of a master switch able to ensure the complete interruption of the power supply to the Product. -
Page 7: Graphic Symbols Used In The Installation Manual
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 7 di 19 Atmospheric pressure (h/Pa): 500 / 1060 Storage The devices packaged must be stored (warehoused) in a dry place and at the following temperature: Temperature (°C): -15 / +60 Humidity: 10 / 75 % Atmospheric pressure (h/Pa): 500 / 1060 Installation site The site appointed for the installation of the equipment must have the... -
Page 8: Graphic Symbols Used On The Package
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 8 di 19 Graphic symbols used on the package The symbols present on the boxes of the packages are listed below: High side of the package Maximum number of packages stackable Breakable package Humidity-suffering package Do not overlap packages with pallet Weight of the package Other graphic symbols used on the Product... -
Page 9: Warranty Certificate
1. The appliance is covered by an 18-month warranty, including electrical parts. 2. The warranty begins on the date of Product shipment from the RIMSA warehouse to the buyer. 3. In case of disputes, the date indicated on the “transport document” attached to the goods shall be deemed valid. -
Page 10: Mechanical And Electrical Arrangement Of The Site
12. The component parts replaced under warranty must only be returned to RIMSA, if so requested by RIMSA, carriage free and suitably packed. 13. In case of failure to return a part requested by RIMSA, the cost of the component part will be charged. - Page 11 MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 11 di 19 After making sure that the site used as medical premises complies with the requisites required above, proceed to the mechanical anchorage of the ceiling plate determining the type of ceiling for the anchorage and acting accordingly.
- Page 12 MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 12 di 19 Using the paper template attached to this manual, mark all the 6 fixing holes of the chosen point of the ceiling. Make the first hole according to the safety anchor diameter. By means of a pump or vacuum cleaner with pipe terminal, remove the dust and the small drilling...
-
Page 13: Electrical Arrangement Of The Site
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 13 di 19 Plate and counter-plate must be enclosed to each other with M10 steel threaded bars each, blocked at the upper and lower ends by respective washers, nuts and lock nuts. Electrical arrangement of the site DANGER The electrical system arrangement works of the site used as medical premises to power the Product must be carried out in a safe way according... -
Page 14: Installation Horizontal Arm To Anchoring Tube
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 14 di 19 See drawing 38 After making the holes (3) to the wall (1), set the plate (2) to the ceiling through the use of bolts (4) by always using the spirit-level (5). See drawing 127 Make sure the power wires to the Product (1) reach the frame of the lamp power without creating interference with the anchoring tube. -
Page 15: Oscillating Arm Installation
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 15 di 19 3.1.3 Oscillating arm installation See drawing 116 Align the oscillating arm pivot (1) with the horizontal arm (2). After connecting the terminals of the electric cables (3) with (4) among each other, insert the pin of the oscillating arm into the pipe of the horizontal arm and screw in the three screws M5x12 DIN7991(5) by use of hexagon key (6) To help the insertion of connectors pull the cables from the slot located on... -
Page 16: Mobile Version (Pentaled 81/105)
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 16 di 19 Mobile version (PENTALED 81/105) 3.2.1 Base with wheels installation See drawing 133 take the base (1), turn the arms of wheels (2) into the final position, aligning the holes of base with the holes of arms of wheels. Screw strongly the 8 screws M10x40 DIN912 (3) of the arms of wheels with an allen key. -
Page 17: Connecting To Electrical Plant
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 17 di 19 Connecting to electrical plant DANGER – Danger of electric shock Before carrying out the electrical connections, check that the power line is NOT under tension in order to proceed with the montage safely. The group of the Product power (support plate, transformer, terminal block) as explained above, is designed to be fixed on the anchoring tube (for the ceiling device version) or it is enclosed inside mobile base cover (for mobile... -
Page 18: First Starting
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 18 di 19 First starting CAUTION It is now possible to power the Product to check its starting with light emission. To do so, it is necessary to: 1 – close the circuit through the network switch upstream of the wiring (charged to the customer) 2 –... -
Page 19: Note
MI_006_GB 13/09/12 Installation manual Rev.4 Pag. 19 di 19 Note... - Page 20 CEILING PLATE SHEET TEMPLATE SCALE1:1 Drawing code Sheet format: A3 Rev. Data...
- Page 21 Drawing code Rev. Data...
- Page 22 Tube external diameter: Ø120 n°6 x Ø18 holes Drawing code Rev. Data...
- Page 23 Drawing code Rev. Data...
- Page 24 Drawing code 40_JP_81 Rev. Data...
- Page 25 Drawing code Rev. Data...
- Page 26 (new installation procedure due to change to the product. Starting from S/N 120928-04834/1, excluded S/N 121010-04597/1/2/3) Drawing code Rev. Data 18/07/2012...
- Page 27 Drawing code Rev. Data...
- Page 28 Drawing code Rev. Data...
- Page 29 Drawing code Rev. Data...
- Page 30 Drawing code Rev. Data...
Need help?
Do you have a question about the PENTALED81 and is the answer not in the manual?
Questions and answers