Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Talkpool OY1210
Summary of Contents for Talkpool OY1210
- Page 1 OY1210 LoRaWAN CO2 meter User manual Version 0.4 October 2019...
-
Page 2: Table Of Contents
Measurement value ......................14 9.3.3 Example: Single measurement report .................. 15 Downlink commands and queries .................... 16 9.4.1 Measurement and reporting interval ................... 19 9.4.2 Reset device.......................... 19 Uplink query response......................19 OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 3: Disclaimer
This document represents information on products at the time of publication and is subject to change without prior notice due to product improvements or other reasons. Talkpool makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. -
Page 4: Warnings
• The product should not be exposed to extreme heat or open flame. • The device must not be exposed to harsh chemical agents or solvents. • The labelling of the product may not be changed, removed or made unrecognizable. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 5: Environmental
For further information concerning your nearest recycling center, please contact your nearest local authority/town hall offices, your household waste collection company or the shop where you bought the product. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 6: Product Description
4 Product Description The OY1210 LoRaWAN CO2 meter is designed to measure carbon dioxide, temperature and humidity in indoor environments. The sensor is intended for indoor climate control, air quality monitoring and energy optimizations. It is optimized for reliable and secure measurements with more than 5 years life length on batteries. -
Page 7: Installation And Activation
The bottom piece is mounted on the wall with the “UP” arrow upwards. It can be mounted either with screws or adhesive tape, both included in the package. The hole pattern matches a standard junction box. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 8: Lorawan Configuration
Configuration on the network server is done with AppEUI: 70-B3-D5-D7-2F-F8-18-00 (a.k.a. JoinEUI) It is possible to order a batch of devices configured with a customer unique AppEUI from the Talkpool OUI range. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 9: Sensor States And State Check
AppKey is distributed by the sales team. The device is default configured for OTA provisioning. Contact the Talkpool team for ABP configuration. The device follows the LoRaWAN standard related Join configuration parameters, such as RX1 and RX2 windows, RX2 downlink frequency etc. -
Page 10: Re-Join Functionality
The device tries to re-join the network if it has not heard anything from the network for 288 uplinks (4 days @ 20-minute message interval). The device requests and normally gets a downlink ever 64th uplink due to the ADRAckReq functionality. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 11: Specification
Security Algorithms AES-128 Hardware Cryptographic co-processor Features Secure boot Secure firmware upgrade Hardware based ultra-secure key storage Battery life Battery life length >5 years (at 20-minute intervals, SF12) + 1 year storage OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... - Page 12 Transmission intervals 20 minutes, configurable over the air Threshold for adaptive reporting >750 ppm Step threshold for adaptive report 100 ppm Unique App EUI available upon request Enclosure IP30 Certifications RoHS compliant LoRaWAN OY1210 LoRaWAN CO2 meter, User manual, Version 1.0...
-
Page 13: Battery Life
The sensor polls the server for configuration parameters the during the Configure state. This is done by sending unsolicited uplink status report (0x20). This gives quick feedback to the installer that the installation has been successful and enables downlink configuration OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 14: Periodic Measurement Reports
Byte 1: Relative humidity, bit 11 – bit4 Byte 2: bit 7-4: Temperature, bit 3 – bit 0 bit 3-0: Relative humidity, bit 3 – bit 0 Byte 3-4: CO2 sent as an unsigned 16-bit integer OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 15: Example: Single Measurement Report
Data sent on LoRaWAN port 2 : 3e 44 1d 02 1b (3e1) : (993) => 993/10 -80°C => 19.3 gradC (44d) : (1101) => 1101/10 – 25% => 85.1 % RH (021b) : (539) => 539 ppm CO OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... -
Page 16: Downlink Commands And Queries
All downlink application communication is done on LoRaWAN port 1. Downlink command network => device Field Bytes Value Description Note Type 0x01: Set 0x02: Query 0x03: Action Index Command Index Data As defined for Command Index only applicable for set-commands OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... - Page 17 Default 750ppm 0x34 Internal CO2 Uint32 CO2 sensor 1-2000 Query Query only, for internal use sensor status bits Big endian status OY1210 LoRaWAN CO2 meter, User manual, Version 1.0...
- Page 18 Data [ Uint12, (°C + 80)*10 0 – 3800 Current temperature, humidity and CO2 See Ch 9.3 Uint12, (% RH 0 – 1500 level. Uint16 ] +25)*10 0 - 65535 (ppm CO OY1210 LoRaWAN CO2 meter, User manual, Version 1.0...
-
Page 19: Measurement And Reporting Interval
Example: Remote device reset: Port 1: 0305 9.5 Uplink query response Uplink messages are sent on port 1 with the following heading: Uplink command device => network Field Bytes Value Description Note OY1210 LoRaWAN CO2 meter, User manual, Version 1.0... - Page 20 As defined for Command Index (only for Type: Data) Example: Port 1: Payload 0x01 20 00 0x01: Data type 0x20: Status command 0x00: Normal startup The expected behavior is 0x01 20 00. If not contact support. OY1210 LoRaWAN CO2 meter, User manual, Version 1.0...