Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Paugge ENT-MX20B8X8
Summary of Contents for Paugge ENT-MX20B8X8
- Page 1 Paugge ENT-MX20B8X8 18Gbps 8x8 HDMI Matrix with ARC Function VER 1.0...
-
Page 2: Table Of Contents
Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. -
Page 3: Introduction
1. Introduction Paugge 18Gbps 8x8 HDMI Matrix supports the transmission of video (up to 4K2K@60Hz YUV 4:4:4) and multi-channel high resolution digital audio from 8 HDMI sources to 8 HDMI displays. Audio de-embedded to analog and coaxial audio is supported from 8 HDMI output ports. -
Page 4: Specifications
4. Specifications Technical HDMI Compliance HDMI 2.0b HDCP Compliance HDCP 2.2 and HDCP 1.4 Video Bandwidth 18Gbps Up to 4K2K@50/60Hz (4:4:4) Video Resolution Color Space RGB, YCbCr 4:4:4/4:2:2/4:2:0 Color Depth 8-bit, 10-bit, 12-bit HDMI Audio Formats LPCM 2/5.1/7.1, Dolby Digital, DTS 5.1, Dolby Digital+, (Pass-through) Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos, DTS:X Coax Audio Formats... -
Page 5: Operation Controls And Functions
5. Operation Controls and Functions Front Panel MENU POWER INPUT 18Gbps 8x8 OUTPUT HDMI Matrix ENTER DOWN LOCK Name Function Description Display matrix switching status, input / output port, EDID, OLED screen Baud rate, IP Address. The LED will illuminate in green when the product is connected Power LED to power supply, and red when the product is on standby. - Page 6 Rear Panel COAX L/ R IR EXT OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 RS-232 TCP/IP OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 CONTROL DC 12V IN 1...
-
Page 7: Ir Remote
6. IR Remote ① Power on or Standby: Power on the Matrix or set it to standby mode. ② Input 1/2/3/4/5/6/7/8: Select input source button. : Select the last or next input source button. Input ③ Output 1/2/3/4/5/6/7/8 button: Select output source button. -
Page 8: Ir Cable Pin Assignment
The second way: If the IR receiver window of the Matrix is blocked or the Matrix is installed in a closed area out of infrared line of sight, the IR receiver cable can be inserted to the “IR EXT” port to receive the IR remote signal. The furthest distance of using the IR remote is 7 meters and the IR remote is directly faced to the IR receiver head. -
Page 9: Edid Management
8. EDID Management This Matrix has 21 factory defined EDID settings, 2 user-defined EDID modes and 8 copy EDID modes. You can select defined EDID mode or copy EDID mode to input port through front panel buttons, RS-232 control or Web GUI. On the initial OLED display screen, press “MENU”... - Page 10 The defined EDID setting list of the product is shown as below: EDID Mode EDID Description 1080p, Stereo Audio 2.0 1080p, Dolby/DTS 5.1 1080p, HD Audio 7.1 1080i, Stereo Audio 2.0 1080i, Dolby/DTS 5.1 1080i, HD Audio 7.1 3D, Stereo Audio 2.0 3D, Dolby/DTS 5.1 3D, HD Audio 7.1 4K2K30_444, Stereo Audio 2.0...
-
Page 11: Web Gui User Guide
9. Web GUI User Guide The Matrix can be controlled by Web GUI. The operation method is shown as below: Step 1: Get the current IP Address. The default IP address is 192.168.1.100. You can get the current Matrix IP address in two ways: The first way: You can get the IP address via panel buttons. - Page 12 After entering the password, click the “LOGIN” button and the following Status page will appear. ■ Status Page The Status page provides basic information about the installed firmware version and the network settings of the device. ■ Video Page You can do the following operations on the Video page: ①...
- Page 13 ■ Input Page You can do the following operations on the Input page: ① Inputs: Input channel of the device. ② Active: It indicates whether the channel is connected to a signal source. ③ Name: The input channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box (Chinese name is unsupported).
- Page 14 ■ Output Page You can do the following operations on the Output page: ① Outputs: Output channel of the device. ② Name: The current output channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box (Chinese name is unsupported). ③...
- Page 15 ■ Network Page Set the Default Network Click “Set Network Defaults”, there will be a prompt, as shown in the following figure: Click “OK” to search the IP Address again, as shown in the following figure: After searching is completed, it will switch to the login page, the default network setting is completed.
- Page 16 Modify Username Click the “User” button, enter the correct Old Password, New Password, and Confirm Password, then click “Save”. After successful modification, there will be a prompt, as shown in the following figure: Note: Input rules for changing passwords: (1) The password can’t be empty. (2) New Password can’t be the same as Old Password.
-
Page 17: Rs-232 Control Command
Get current power state power on/power off Reboot... System Initializing... s reboot! s reboot! Reboot the device Initialization Finished! FW version x.xx.xx System Setup help! help! List all commands r type! Get device model r type! ENT-MX20B8X8 - 15 / 20 -... - Page 18 Set the logo name displayed on s logo2 s logo2 logo2 the second line of LCD screen,the ****************! ENT-MX20B8X8! ENT-MX20B8X8! max character is 16 Set the serial port baud rate of s baud rate s baud rate xxx! RS02 module, z=(115200,57600,...
- Page 19 Example Command Code Function Description Feedback Default Setting Enable hdmi output 1 stream Disable hdmi output 1 s hdmi 1 stream 1! Set output y stream on/off, y=0~8 stream s hdmi y stream z! enable (0=all) z=0~1(0:disable,1:enable) Enable hdmi all outputs s hdmi 0 stream 1! stream Disable hdmi all...
- Page 20 Example Function Description Feedback Command Code Default Setting CEC Setting set input x power on by CEC, input 1 power on s cec in x on! s cec in 1 on! x=0~8(0=all input) set input x power off by CEC, input 1 power off s cec in x off! s cec in 1 off!
- Page 21 Example Function Description Feedback Command Code Default Setting Network Setting IP Mode: Static IP: 192.168.1.72 Subnet Mask: 255.255.255.0 r ipconfig! Get the Current IP Configuration r ipconfig! Gateway: 192.168.1.1 TCP/IP port=8000 Telnet port=10 Mac address: 00:1C:91:03:80:01 Mac address: r mac addr! Get network MAC address r mac addr! 00:1C:91:03:80:01...
-
Page 22: Application Example
Example Command Code Function Description Feedback Default Setting Network reboot… IP Mode: Static IP: 192.168.1.72 Subnet Mask: 255.255.255.0 s net reboot! Reboot network modules s network reboot! Gateway: 192.168.1.1 TCP/IP port=8000 Telnet port=10 Mac address: 00:1C:91:03:80:01 11. Application Example Amplifier 2.0 Speakers COAX L/ R...