Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SENTRY II 952 Series
- Page 1 Series 952 Service Manual...
- Page 2 SENTRY!II!!Series 952...
-
Page 3: Table Of Contents
Table of Contents TABLE!OF!CONTENTS Page General Warnings ........................4 Installation ..........................5 Programming ......................... 7 System Start-Up ........................9 Frequently Asked Questions ....................10 Front Cover and Drive Assembly Breakdown ..............12 Internal Parts Breakdown ....................13 Injector Assembly Breakdown .................... 14 Brine Elbow Assembly Breakdown .................. -
Page 4: General Warnings
Introduction General Warnings 1. The control valve, fittings and/or bypass are ware version (e.g. 204) and then reset the valve to designed to accommodate minor plumbing mis- the service position. alignments but are not designed to support the weight of a system or the plumbing. 6. -
Page 5: Installation
Installation Pre-Installation Checklist 5. Plumbing preparation: Un-screw the two plas- tic nuts (#1) and pull on the two brass connectors 1. A standard electrical outlet (120V/60Hz) must be (#4) to remove them from the bypass assembly. located within 12’ of the installation site. Next remove the white plastic split rings (#2) and the O-Rings (#3). - Page 6 Installation 10. Temporary Drain Tube: Now that the water 14. Connecting the overflow line: The brine softener is connected to the existing plumbing, overflow fitting is located on the outside of the the drain line may be connected. First, discon- salt container approximately 12”...
-
Page 7: Programming
Programming Programming the Controller 2. Setting the Water Hardness, Day Override and regeneration times: 1. Setting the Clock: When the controller is first plugged in, the time of day display will be flash- Step 1: Press and hold the NEXT button and ing. - Page 8 Programming Step 3 Setting the Day Override: The “SET Step 5: The minute display will now be flashing. REGEN DAY” display will now be flashing. This Set the correct minutes by pressing either the setting is used to force a regeneration after a pre- or the arrow button.
-
Page 9: System Start-Up
System Start-Up Start -Up Instructions Step 3: Press the REGEN button. The drive motor will run and the “BRINE” display will flash until 1. Adding Water to Salt Container: Manually fill the drive motor stops. the salt container with fresh water until there is Step 3 approximately 1”... - Page 10 System Start-Up Step 6: Fill the salt container with extra coarse Once the drive motor stops, the manual regenera- water softener salt. The amount of salt placed in tion is complete and the display will return to the the salt container at this time is not critical; how- normal display.
-
Page 11: Frequently Asked Questions
Frequently Asked Questions Frequently Asked Questions 5. Question: How often does the salt tank need to be cleaned? 1. Question: What type of salt can I use in this softener? Answer: Dirt, rocks and debris collect in the bottom of the Answer: salt container (a little in each bag of salt). -
Page 12: Front Cover And Drive Assembly Breakdown
Front Cover and Drive Assembly Breakdown Page 12 SENTRY!II!!Series 952... -
Page 13: Internal Parts Breakdown
Internal Parts Breakdown SENTRY!II!!Series 952 Page 13... -
Page 14: Injector Assembly Breakdown
Injector Assembly Breakdown Page 14 SENTRY!II!!Series 952... -
Page 15: Brine Elbow Assembly Breakdown
Brine Elbow Assembly Breakdown SENTRY!II!!Series 952 Page 15... -
Page 16: 3/4" Drain Fitting Breakdown
3/4” Drain Fitting Breakdown Page 16 SENTRY!II!!Series 952... -
Page 17: 1" Drain Fitting Breakdown
1” Drain Fitting Breakdown SENTRY!II!!Series 952 Page 17... -
Page 18: Meter Assembly Breakdown
Meter Assembly Breakdown Page 18 SENTRY!II!!Series 952... -
Page 19: Installation Fitting Assemblies
Installation Fitting Assemblies SENTRY!II!!Series 952 Page 19... -
Page 20: Bypass Assembly Breakdown
Bypass Assembly Breakdown Page 20 SENTRY!II!!Series 952... -
Page 21: Bypass Valve Operation
Bypass Valve Operation SENTRY!II!!Series 952 Page 21... -
Page 22: Trouble Shooting Procedures
Trouble Shooting Procedures Page 22 SENTRY!II!!Series 952... - Page 23 Trouble Shooting Procedures SENTRY!II!!Series 952 Page 23...
- Page 24 L-952-SM Printed in the U.S.A. Rev. 12/07...
Need help?
Do you have a question about the 952 Series and is the answer not in the manual?
Questions and answers