Download
Share
Print this page
  1. Manuals
  2. Brands
  3. imovr Manuals
  4. Racks & Stands
  5. EMMA
  6. Installation manual

imovr EMMA Installation Manual

Electric multi-monitor arm
Hide thumbs

Advertisement

Quick Links

Download this manual
EMMA
Electric Multi-Monitor Arm
INSTALLATION MANUAL

Advertisement

loading

Summary of Contents for imovr EMMA

  • Page 1 EMMA Electric Multi-Monitor Arm INSTALLATION MANUAL...

  • Page 2: Pre-Installation

    6 monitors attached maximum total weight 150lbs. iMovR ¾” tops will support 3 monitors on the EMMA to a maximum of 75 lbs. • If you do not have an iMovR desk, please check the material of your desk to be sure it can take the weight load. If unsure you may want to check with the manufacturer of your desk to see what the material of the desktop is made from.
  • Page 3 PARTS EMMA Components 3 Allan wrenches included (4mm, 3/16”, 1/4”)
  • Page 4 VESA mount times the weight of the object). • It is critical that the overall lifted-weight capacity of the EMMA — 120 lbs in standard configuration or up to 150 lbs if using the Heavy Duty Support Collars — has not been exceeded.
  • Page 5 LIFTING COLUMN SETUP Attaching The Controller And Control Box Clear off your desk and carefully flip it upside-down onto a soft Find a free location on the underside of your desk within surface. It may require two people to do this safely. reach of the Handset’s 24”...
  • Page 6 LIFTING COLUMN SETUP Attaching The Controller And Control Box, Continued With assistance, flip your desk right side up. Select the position where you want to clamp the Lifting Column. This will most likely be in the center of the back edge of your desktop.
  • Page 7 IDENTIFY YOUR LAYOUT 1. Single Monitor - Go to Page 8 2. One Row with Two Monitors - Go To Page 10 3. One Row with Three Monitors - Go To Page 16 4. Two rows with One Monitor Each (See future update) 5.
  • Page 8 SINGLE MONITOR Assembling Single Monitor Start by loosening the top four screws on top of the pole for Remove the screw holding the lower bracket to the pole, added maneuverability. and lower it to make space for sliding the VESA Mount on. Slide on the single monitor VESA Mount and then its Re-attach bottom plate with bolt.
  • Page 9 Slide the VESA mount to the desired position along the Attach the monitor. pole, then slide on the retaining ring and bring it up to the bottom of the VESA mount, then tighten down. Initialize the controller. (see page 20) Completed Completed Single Monitor...
  • Page 10 ONE ROW WITH TWO MONITORS Assembling One Row with Two Monitors Start by loosening the top four screws on top of the pole for Remove the screw holding the lower bracket to the pole. added maneuverability. Now gather your beam assembly that consists of two nylock Insert the beam bushings on the inside of the beam pole nuts, two bolts, two beam bushings, and two monitor arm mount.
  • Page 11 Place the beam assembly onto the pole flat side Screw in the two bolts, taking care to make an equal facing up. Slide it up the pole to roughly the desired number of turns to each. Once tightened evenly, loosen height for monitor.
  • Page 12 ONE ROW WITH TWO MONITORS Assembling One Row with Two Monitors Attach Quick Connect Brackets. If the Quick Connect Install the beam end cap for both sides. Brackets do not fit on your monitor, mount the monitor directly to the VESA plate. Position the arms symmetrically on either end of the Align beam with the back edge of the desk.
  • Page 13 Slide two monitors together. Attach both monitors to the VESA mounts on those arms. Initialize the controller. (see page 20) Completed Completed One Row with Two Monitors...
  • Page 14 ONE ROW WITH THREE MONITORS Assembling One Row with Three Monitors Start by loosening the top four screws on top of the pole for Remove the screw holding the lower bracket to the pole. added maneuverability. Now gather your beam assembly that consists of two nylock Insert the beam bushings on the inside of the beam pole nuts, two bolts, two beam bushings, and two monitor arm mount.
  • Page 15 Slide on the single monitor VESA Mount and then its Place the beam assembly onto the pole and slide it up retaining ring onto the pole. Note the arrow on the VESA about 2 inches above the bottom of the pole with the flat Mount should be pointing up as shown.
  • Page 16 ONE ROW WITH THREE MONITORS Assembling One Row with Three Monitors Loosen or tighten the monitor arm’s so you can move them Slide the cable management clips onto both sides. in the channel freely. Install the beam end cap for both sides. Attach Quick Connect Brackets.
  • Page 17 CONTINUED Position the arms symmetrically on either end of the To do this you will need to remove you monitors to move beam. Note: to achieve ConstantFocus on your displays your monitor arms. you will need to set the arms further out from the center. (see page 22) Once proper viewing angle and spacing has been achieved, Align beam with the back edge of the desk.
  • Page 18 ONE ROW WITH THREE MONITORS Assembling One Row with Three Monitors Reinstall your flanking monitors. Install your center monitor. Measure the height difference from your center monitor to Adjust your center VESA mount retaining ring the same one of your flanking monitors. distance that you measured.
  • Page 19 CONTINUED Align all three monitors. Initialize the controller. (see page 20) COMPLETED Completed One Row with Three Monitors...

  • Page 20: Controller Operation

    How to set a minimum allowable height 1. Lower the EMMA to the lowest position you’d like it to reach (for example, safely above any items on the desktop it might run into). 2. Press the “Bluetooth” button and press the paddle DOWN at the same time until the LED light flashes.
  • Page 21 EMMA can lift 120 lbs of total weight using the standard VESA mounts, or up to 150 lbs total weight if using the HD Support Collars. EMMA’s ratings do not account for weight added more than 22” beyond the front of the column or more than 42” to the left or right of the column.

  • Page 22: Warranty

    You can request in writing that iMovR responsibly dispose of the product for you. If iMovR notifies you that a returned product is not defective after testing, then the product will be returned to you. You would be responsible for the freight charges associated with the return.
  • Page 23 20″–30″ from their screens. With Its breakthrough ConstantFocus™ wrap-around adjustability, the EMMA keeps all of your displays at the same focal depth. This reduces strain on your eyes’ ciliary muscles and speeds your brain’s processing of visual information. For stock traders, dispatchers, gamers, and other users who need to have the fastest hand-eye-brain coordination, no other single monitor arm can deliver the goods.
  • Page 24 EMMA Electric Multi-Monitor Arm IMovR Contact Information: Phone: (888) 208-6770 or (425) 999-3550 Fax: (425) 999-3550 E-mail: customercare@iMovR.com Live Chat: www.iMovR.com DOC-EM-MAN1 (4/2022) Hours: See iMovR.com/hours...