Subscribe to Our Youtube Channel
Related Manuals for Thermo Savant SPEEDVAC SPD Series
Summary of Contents for Thermo Savant SPEEDVAC SPD Series
- Page 1 PEEDVAC CONCENTRATOR ® SPD-SERIES BASIC SPD101B INSTRUCTION MANUAL A Thermo Electron business...
-
Page 2: Table Of Contents
Table of Contents Section Section Title — Overview Page Overview of the SPD101B Unit Installation of the SPD101B Unit How to Hook Up the SPD101B Unit Section Section Title — Control Panel Page The Control Panel Description of the Control Panel Section Section Title —... -
Page 3: Overview Of The Spd101B Unit
Overview of the SPD101B Unit Figure 1 = Front View Figure 2 = Side View Fig. 1 Figure 3 = Back View Top Cover Control Panel Front Panel Left Side Panel Anti Skid/Vibration Fig. 2 Right Side Panel Chamber View Window Vacuum Port AC Socket 10. -
Page 4: Installation Of The Spd101B Unit
® Unpack unit from box and verify all parts match packing list. Read instruction manual carefully! If assistance is required, call Thermo Savant Customer Care at 1-800-634-8886, 631-244-2929, Fax: 631-244-0606. If the unit is part of a larger system, use vacuum tubing supplied to hook up unit. -
Page 5: The Control Panel
SPD101B Control Panel Description of SPD101B Control Panel MODIFY TEMPERATURE UP/DOWN - Modifies selected parameter. RUN/STOP - Starts a manual run, Terminates a manual run. VIEW - Press to view the preset parameters during the run. TEMPERATURE DISPLAY (GREEN DISPLAY)- Indicates set temperature or actual temperature during pre-heat or during a run from 45 ˚C to 80 ˚C, or “NO”... -
Page 6: Pre-Heat Function
3 . 0 P R E - H E AT F U N C T I O N • Used to pre-heat chamber prior to or between runs. • The chamber will always pre-heat to the set point on the display. (see page 3 on how to modify setpoint temp.) •... -
Page 7: Rotor Selection Guide
To End Run There Are 2 Steps: Close manual bleeder and allow atmospheric air to bleed into the chamber. To stop rotor, press RUN/STOP button, (GREEN light is OFF). Display shows END. Once rotor stops turning, cover lock opens. The display reverts to last set-parameters. -
Page 8: Guideline For Solvent Choice
SPD101B may cause the lid material to become discolored and cause potential damage. For addi- tional technical assistance with respect to your solvent choice, please contact the Applications Support Specialists, at Thermo Savant at 1-800-634-8886 or 631-244-2929 or Fax 631-244-0606. -
Page 9: Maintenance/Service
Replace chamber seal if cracked (Part number is 197-6020-00). Outside of unit can be cleaned with dilute solution of soap and water. For any other maintenance or service issues or service problems, please call the Thermo Savant Service Department at: 1-800-717-5509, 631-244-6942, Mon-Fri 8:00AM - 7:00PM E.S.T. -
Page 10: Specifications/Warranty
FORM. PLEASE CALL 1-800-717-5509, OR 631-244-6942 TO HAVE THIS FORM FAXED TO YOU! Under no circumstances shall Thermo Savant be liable for dam- ages due to the improper handling or use of its products. Thermo Savant assumes no liability, express or implied, for use of this equipment. -
Page 11: Appendix 1 - Additional Spd101B System Set-Ups
APPENDIX 1 Additional SPD101B System Set-ups BV130 Vacuum Bleeder Valve Tubing ANT100 ® SpeedVac Concentrator UVS400 SPD101B Universal Vacuum Source SEMI-INTEGRATED LOW VACUUM SYSTEM Flexible Vacuum Tubing BV130 Bleeder Valve DVG50 ® SpeedVac Concentrator RVT400 SCT120 VLP80 SPD101B Cold Trap Chemical Trap Vacuum Pump COMPONENT HIGH VACUUM SYSTEM... - Page 12 SPD SERIES SPEEDVAC FAMILY ® SPD101B SPD111V SPD121P...
- Page 14 100 Colin Drive • Holbrook, NY 11741-4306 USA Tel: 631-244-2929 • 1-800-634-8886 • Fax: 631-244-0606 www.thermosavant.com • E-mail: savantec@savec.com 197-3000-00 Rev. B A Thermo Electron business ©2000 Thermo Savant...
Need help?
Do you have a question about the SPEEDVAC SPD Series and is the answer not in the manual?
Questions and answers