Related Manuals for ETC SealerAtor
Summary of Contents for ETC SealerAtor
- Page 1 High End Systems SealerAtor IP Tester User Manual Version 1.0.0 Part Number: 2599M1200-1.0.0 Rev: A Released: 2022-08...
- Page 2 To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. You can find complete High End Systems terms and conditions and warranty information at etcconnect.com/Support/Warranty.aspx.
-
Page 3: Table Of Contents
General Guidelines Unpacking Instructions Specifications Environment Electrical Overview Control Operation Connect the SealerAtor to the Fixture Perform the Test Disconnect the SealerAtor from the Fixture Onboard User Interface Menus SealerAtor Software Install SealerAtor Software on a PC Perform a Test... - Page 4 Maintenance Clean the SealerAtor Update Firmware on the SealerAtor Troubleshooting an Unsuccessful Firmware Update SealerAtor User Manual...
-
Page 5: Introduction
Introduction Congratulations on your purchase of the SealerAtor IP tester. The SealerAtor is a service tool that tests for pressure and vacuum leaks in IP-rated fixtures after they have been opened for maintenance or repairs. This manual provides important information for the safe operation and maintenance of the SealerAtor. -
Page 6: Help From Technical Services
Help from Technical Services If you have questions that are not answered by this document, try the ETC support website at support.etcconnect.com or the High End Systems product website at etcconnect.com/Products/High-End-Systems. If none of these resources are sufficient, contact ETC Technical Services directly at one of the offices identified below. Emergency service is available from all offices outside of normal business hours. -
Page 7: Safety Considerations
This equipment is intended for professional use only. Not for residential use. • Read the entire manual before using this equipment. • Contact your authorized ETC dealer or ETC Technical Services before performing any • service in order to maintain warranty coverage. WARNING: Note the following safety warnings before use: This equipment is designed for operation by qualified personnel only. -
Page 8: General Guidelines
Applying power to a cold device may cause damage to the device and void the manufacturer warranty. Please use the original packaging if the device is to be transported. ETC will not be •... -
Page 9: Unpacking Instructions
Unpacking Instructions The SealerAtor IP tester includes: One SealerAtor IP tester • ® ® One power input cable with powerCON TRUE1 TOP locking connector • One air hose • One USB cable • One microSD memory card • One threaded bolt •... -
Page 10: Overview
7 USB connector 8 Air intake and release valve for the SealerAtor Control You control the operation of the SealerAtor by using the onboard user interface or the SealerAtor software. Onboard The onboard user interface consists of a display and navigational controls. See •... -
Page 11: Operation
One threaded bolt (provided with the SealerAtor) • One rubber washer (provided with the SealerAtor) • One microSD card (provided with the SealerAtor, or any microSD card 8 GB or larger) • Note: Inspect the rubber washer before use, and replace the washer if it is damaged or brittle. -
Page 12: Perform The Test
• complete. 3. Attach the air hose to the SealerAtor by connecting the quick connect plug on the air hose to the "Pressure/Vacuum to Fixture"quick connect coupler on the SealerAtor. 4. Using an adjustable wrench, attach the fitting on the other end of the air hose to the air valve located on the fixture upper enclosure. -
Page 13: Onboard User Interface
Onboard User Interface You can control the operation of the SealerAtor through the onboard user interface, which consists of a display and navigational controls. 1. Press the [MODE/ESC] button Mode to access the main menu Esc. 2. Browse the menu by pressing the up, down, left, or right navigation buttons, and press the Enter button to select a menu item. - Page 14 • Test the SealerAtor Navigate: Main Menu → Test → Self-Test Do not use the Self-Test option unless directed to do so by ETC Technical Services. Contact Help from Technical Services on page 2 Technical Services for specific instructions. Refer to contact information.
- Page 15 Available View and change the pressure, vacuum, and hold time values Set Fixture • Fixtures and used during testing, or delete a fixture from the SealerAtor. Settings The test values displayed are predefined for the fixture. ETC Delete Fixture •...
-
Page 16: Sealerator Software
SealerAtor Software Contact ETC Technical Services for assistance in installing the SealerAtor software on a PC. Refer to Help from Technical Services on page 2 for contact information. The SealerAtor software includes predefined profiles for ETC fixtures that are compatible with the SealerAtor. -
Page 17: Open Saved Test Results
3. Open the SealerAtor software on the PC. 4. Select the fixture you want to upload to the SealerAtor. 5. Select Upload. The profile is uploaded to SealerAtor and is available to be selected in the onboard user interface. Operation... - Page 18 To close the SealerAtor Update window without updating the firmware, select OK or the X in the upper right corner of the window. 9. When the firmware update is complete, select OK to close the SealerAtor Update window. SealerAtor User Manual...
- Page 19 If the firmware update is not successful: 1. Power off the SealerAtor for at least 5 seconds, and then power it back on. 2. When the start up procedure is complete and the main menu is shown in the display on the Update Firmware on the SealerAtor on the previous page SealerAtor, repeat steps 5–10 in...
- Page 20 | Support support.etcconnect.com | Contact etcconnect.com/contactETC © 2022 Electronic Theatre Controls, Inc. | Trademark and patent info: etcconnect.com/ip Product information and specifications subject to change. ETC intends this document to be provided in its entirety. 2599M1200-1.0.0 Rev A Released 2022-08...
Need help?
Do you have a question about the SealerAtor and is the answer not in the manual?
Questions and answers