Advertisement
3.
OPERATION
3.1
FAN OPERATION.
WARNING! Ensure you read, understand and apply the safety instructions in part 1
before using the fan.
p
3.2
Carry the fan to a suitable location using the carrying handle recess provided in the top part of the
rear moulding. ( see fig. 3-G )
3.3
Before pluging the fan into the mains supply set the left hand Speed Control Knob (D) to the
“0” - Stop position, and the right hand Timer Knob (E) to the “ON” position ( see fig. 2 ) Now plug
the fan into the mains supply. The fan will begin to turn when you select one of the speeds.
3.4
Speed Control. Turn the Speed Control Knob (D) to select one of the three speeds as follows ;
1 - Low speed, 2 - Mid speed, 3 - High speed. These settings are repeated on both sides of the
knob and either can be used. To stop the fan select the “0” - Stop position.
3.5
Timer Operation. The timer will automatically switch the fan off after the period of time you
select using the Timer Knob (E) up to a maximum of 2 hours. After the fan has been running for the
selected period of time the knob will return to the “ OFF ” position. Once you have finished with the
timer you will need to turn the knob anticlockwise to the “ ON “ position before you can use the fan again.
3.6
Directional Air Control. The circular grill on the front of the fan has specially shaped louvres which
allows control of the direction of the air flow in two ways.
(a) The grill can be made to rotate in the air stream from the fan and this has the effect of spreading
the air flow around the space in which the fan is operating. To achieve this effect turn the large
circular knob (F) in the centre of the grill anticlockwise until the grill can be rotated freely by hand.
Turn the fan onto high speed to get the grill rotating and then adjust the speed as required.
You can stop the grill rotating by turning knob (F) clockwise until the movement slows and stops.
(b) When the front grill is not rotating the air flow is directed away from the grill at an angle. By turning the
grill by hand the airflow can be directed up, down or to either side.
2.2.6
Cleaning the unit. Always disconnect the unit from the mains supply before undertaking any
cleaning. Clean with a soft cloth that has been slightly dampened with a soapy detergent solution.
Do not use solvents or abrasives.
4. PARTS LIST
SBF12 & SBF16
Item. SBF12 No. SBF16 No. DESCRIPTION
1
SBF12/01
B USE
2
SBF12/02
B USE
3
SBF12/03
BUSE
4
SBF12/04
BUSE
5
SBF12/05
BUSE
6
SBF12/06
SBF16/06
7
SBF12/07
BUSE
8
SBF12/08
BUSE
9
SBF12/09
BUSE
10
SBF12/10
BUSE
11
SBF12/11
BUSE
12
SBF12/12
BUSE
13
SBF12/13
BUSE
14
SBF12/14
BUSE
15
SBF12/15
BUSE
16
SBF12/16
B USE
17
SBF12/17
BUSE
18
SBF12/18
BUSE
19
SBF12/19
SBF16/19
20
SBF12/20
SBF16/20
21
SBF12/21
B USE
22
SBF12/22
BUSE
23
SBF12/23
SBF16/23
24
SBF12/24
SBF16/24
25
SBF12/25
B USE
26
SBF12/26
SBF16/26
27
SBF12/27
BUSE
28
SBF12/28
SBF16/28
29
SBF12/29
B USE
Declaration of Conformity
BOX FAN Models SBF12 & SBF16
EN 60335-2-80
89/336/EEC Electromagnetic Compatibility
73/23/EEC Low Voltage Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
NUT COVER
SCREW
LOUVER KNOB
SPRING
WASHER
GRILLE
RUBBER WASHER
SHAFT
SWITCH KNOB
POWER CORD
CORD CLAMP
SCREW
TERMINAL BLOCK
SCREW
SCREW
SCREW
TIMER
SCREW
REAR CABINET
STAND
SCREW
TIMER KNOB
FRONT CABINET
CAPACITOR
ROTARY SWITCH
MOTOR
SCREW
FAN
SCREW
We, the sole importer into the UK, declare that the products listed below are in conformity with the following EEC standards and directives
The construction file for these products are held by the Manufacturer and may be inspected on request by contacting
Jack Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
fig 2
fig 3
Original Date:-
Version No:-
Date Modified:-
For Jack Sealey Ltd.
Sole importer into the UK
3rd January 2001
of Sealey Power Products
E-mail: sales@sealey.co.uk
SBF12 & SBF16 -(F2053 ) - (1) 020101
040101
1
1st Issue
Advertisement
