Summary of Contents for Satco STARFISH S11267
- Page 1 START HERE In-Wall Wi-Fi Switch S11267 Installation Guide WIFI 2.4GHz NO HUB NEEDED...
- Page 2 This switch is rated for Incandescent, CFL, LED and resistive loads as well as motors 120VAC 60HZ 6A (720W) INC, CFL, LED, Resistive, 3.6A Motor NOTE: A NEUTRAL WIRE IS REQUIRED FOR INSTALLATION No Derating is required when installing in multi-gang applications.
- Page 3 WARNING: 50MM, OR A NON-METALLIC BOX. Note: This equipment has been - Connect the equipment into an tested and found to comply with the outlet on a circuit different from that This product may represent a - ONLY USE WITH SOLID COPPER limits for a Class B digital device, to which the receiver is connected.
-
Page 4: Operation
OPERATION 1) Power Indicator & Confi guration Light 2) On/Off Switch... -
Page 5: Parts Included
PARTS INCLUDED Wall plate Mounting (x1) frame (x1) Smart switch (x1) Inner frame Mounting screws screws (x2) (pre-installed) (x2) - Page 6 Verify that a neutral wire is available prior to installation How do I know if I have a neutral wire? 1. Turn power off at your breaker box and ensure the power is off 2. Remove the wall plate and existing device from the wall box 3.
-
Page 7: Switch Installation
SWITCH INSTALLATION Turn power OFF at the circuit breaker and ensure power is off. WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse and test that power is off before wiring. CONTINUED ON OTHER SIDE... - Page 8 Identify if your wiring is SINGLE POLE or 3-WAY SINGLE POLE: control from a single location 3-WAY: control from 2 locations...
- Page 9 You will need to determine which is the “LINE” wire and wall box and which is the “LOAD” wire and wall box. Your old switch may have a screw terminal of a different color (usually black). This will either be the “LINE” connection or the “LOAD”...
- Page 10 NOTE: Ensure power is off before preforming this step! Preparing and connecting wires: Use with #12-14 AWG solid copper or copper-clad wire. Strip wires to 2 cm (.8 inch). Insert wires into terminal holes and secure connections by tightening terminal screws to 16 lbf-in (1.8 N.M) as shown.
- Page 11 SINGLE POLE WIRING Ensure that the following connections are made: “LINE” wire to the terminal marked AC-L “LOAD” wire to the terminal marked LOAD Neutral wire to the terminal marked AC-N Ground wire to the terminal marked GND...
- Page 12 3-WAY WIRING Note: A single pole or 3-way switch can be used alongside the smart switch. IMPORTANT: The switch must be installed in the “LINE” wall box and the smart switch must be installed in the “LOAD” wall box. Ensure that the following Ensure that the following connections are made connections are made...
- Page 13 MOUNTING Push wires into the wall box and push switch into opening Mount the switch into wall box and install the wall plate TESTING Turn power back on at the circuit breaker Test the device to ensure that the lights will turn on and off...
-
Page 14: Troubleshooting
DOWNLOAD THE FREE “STARFISH SMART LIGHTING” APP Please refer to our Starfi sh user guide for detailed instructions on how to pair your device TROUBLESHOOTING Lights are fl ickering: -Lamp has a bad connection. - The switch wire connections are not fi rmly secured. - Page 15 ENJOY THESE OTHER GREAT STARFISH WIFI SMART LED PRODUCTS Technical Support www.satco.com/Starfi sh...
- Page 54 N. MATOS INDUSTRIAL PARK T. 631-243-2022 T. 972-247-2437 T. 305-624-2044 T. 510-487-4822 T. 425-789-3300 T. 787-757-3510 F.631-243-2027 F.972-247-54087 F.305-247-5408 F.510-487-8955 F.425-789-3310 F.787-757-3540 PRODUCTS INVENTORIED IN CANADA & MEXICO: INTERNATIONALSALES@SATCO.COM/631 -243-2022 EXT. 315 © Satco Products, Inc. SATCO.COM | 800-437-2826 All rights reserved 2021...
Need help?
Do you have a question about the STARFISH S11267 and is the answer not in the manual?
Questions and answers