Advertisement
5.
OPERATING INSTRUCTIONS
5.1.
Pre use Inspection.
F
WARNING! INSPECT THE GRINDER BEFORE OPERATING THE MACHINE. ENSURE THE GRINDER IS UNPLUGGED FROM
THE MAINS POWER BEFORE COMMENCING THE INSPECTION.
5.1.1. Check the tool rests are securely fixed at a maximum of 1.5mm from the grinding stone.
5.1.2. Check that eye shields are in good condition, are secure and that you can see through them clearly.
5.1.3. Turn the grinding stones by hand and check for any damage. Check they do not touch the tool rests and are correctly aligned.
If any of the above checks fail, replace, repair, or adjust as necessary before starting the grinder.
5.2.
Stone Use.
Depending on the model, grinders are supplied with one or two aluminous oxide stones. Stones have two grades, fine are preferred
for hard materials and a coarse for soft materials.
When grinding, should surface of the stone become “loaded” (coated with particles of the material being ground) it is probably the
wrong grade of stone for the job.
Important reminder: Grinding stones MUST ONLY be assembled by a person holding a grinding wheel certificate. See Section 4.
5.3.
Using the Grinder.
F
WARNING! Before commencing work, ensure you read, understand and apply the Safety Instructions.
Plug grinder into the mains power supply.
Place the eyeshield in its appropriate safety location.
Switch the grinder on and bring the workpiece slowly into contact with the spinning stone.
Use the entire front face of the grinding wheel surface, avoid grinding grooves in the stone. DO NOT use the side of the stone.
Hold work firmly, and gently move the work across the grinder face. DO NOT push or force the work and DO NOT allow the workpiece
to slip in your hands.
When you have completed your task, unplug the grinder from the mains power supply, and clean the machine ready for next use.
6.
MAINTENANCE
F
WARNING! Ensure the grinder is unplugged from the mans power supply before performing any maintenance or service.
6.1.
As the grinding stone wears, adjust the position of the tool rests. The rest must set at a minimum of 1.5mm from the stone surface.
p
6.2.
Regularly remove the grinding stone covers and clean out any dust and dirt. Refer to part 4.2. to remove covers.
6.3.
The machine motor and bearings are sealed units and require no regular maintenance. Should you require assistance, contact your
local Sealey service agent.
6.4.
For information relating to the handling and maintenance of grinding stones refer to Section 4.
7.
DECLARATION OF CONFORMITY
BENCH GRINDER
Model: BG250XL
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
p
Declaration of Conformity
the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor,
01284 757500
Sealey Group,
Bury St. Edmunds, Suffolk.
We, the sole importer into the UK, declare that the product listed here is in conformity with
6th April 2001
01284 703534
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Quality Machinery.
E-mail: sales@sealey.co.uk
BG250XL - 0064 - (2) - 090801
Advertisement
