Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for TEH LP820
- Page 1 Cordless Planer LP820 Tools for Every Home...
- Page 2 Model LP820 Rated Voltage DC 20V Motor Brush No-Load Speed 15000r/min Planning Width 82mm Battery Planning Depth Lock-off Lever 0-2mm Release Button Rabbeting Depth 0-10mm On/Off Switch Compatible Battery LB4.0Ah Depth Adjustor Battery...
-
Page 3: Electrical Safety
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. -
Page 4: Use And Handling Of The Cordless Electrical Power Tool
SPECIAL SAFETY DIRECTIONS FOR BATTERY-OPERATED TOOLS l) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. a) Ensure that the device is switched off before inserting the battery. Inserting a battery into a n) Use the power tool, accessories and tool bits etc. -
Page 5: Residual Risks
e) Connect the charger only to a socket with an earth. Ensure that the mains voltage matches the a) Cuts specifications on the charger rating plate. Risk of electric shock. b) Ear damage if working without ear protection. f) Disconnect the charger from the mains before closing or opening connection to the battery / c) Damage to your health caused by swinging your hands and arms when operating the appliance power tool / device. -
Page 6: Removing Or Installing Planer Blades
REMOVING OR INSTALLING PLANER BLADES 10. Make sure the blade is not contacting the workpiece before the switch is turned on. 11. Wait until the blade attains full speed before cutting. 12. Always switch off and wait for the blades to come to a complete stop before any adjusting. WARNING 13. - Page 7 1. To remove the blades on the drum, unscrew the installation bolts with the socket wrench. The 2. To install the blades, loosely attach the adjusting plate to the drum cover comes off together with the blades. set plate with the pan head screws and set the mini planer blade on the gauge base so that the cutting edge of the blade 2.To install the blades, first clean out all chips or foreignmatter adhering to the drum or blades.
- Page 8 FOR THE CORRECT PLANER BLADE SETTING When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of Your planing surface will end up rough and uneven, unless the blade is set properly and securely. its contents, tapping it lightly so as to remove particles The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the adhering to the insides which might hamper further collection.
-
Page 9: Adjusting Depth Of Cut
OPERATION INSTRUCTION WARNING 1. For your safety, this tool is equipped with lock-off lever which prevents the tool from unintended starting. never use the tool if it runs when you simply pull the switch trigger without pressing the lock-off lever. Return tool a service center for ADJUSTING DEPTH OF CUT proper repairs before further usage. -
Page 10: Planing Operation
PLANING OPERATION Draw a cutting line on the Adjust the edge fence until it When planing, move the tool workpiece. Insert the edge comes in contact with the with the edge fence flush Hold the tool firmly with one hand on the knob and theother hand on the switch handle when fence into the hole in the front side of the workpiece, then with the side of the... -
Page 11: Maintenance
3. Blade (B) other maintenance or adjustment should be formed by contact the sides (C)and (D). Then tighten the 4. Side (D) wing nuts. TEH Authorized Service Centers, always using TEH 5. Side (C) replacement parts. 1. Brush holdercap 2. Screwdriver... -
Page 12: Warranty Card
WARRANTY CARD Dear customers, the warranty service for purchasing TEH products is as follows: Under normal use, within one year from the date of purchase. It is guaranteed that the damage is caused by the quality of the tool. The following conditions occur during the warranty period, not covered by the warranty: a.
Need help?
Do you have a question about the LP820 and is the answer not in the manual?
Questions and answers