Related Manuals for Arcflash Labs EMG-02
Summary of Contents for Arcflash Labs EMG-02
- Page 1 EMG-02 10 Stage Automatic Coilgun User Manual Arcflash Labs, LLC 8620 Belford Ave, Unit 603 Los Angeles CA 90045 - (424) 256-5087 www.arcflashlabs.com admin@arcflashlabs.com Limited Warranty P a g e...
- Page 2 AS PROVIDED UNDER THIS WARRANTY, IS THE BUYER’S EXCLUSIVE REMEDY. This exclusive remedy will not be deemed to have failed of its essential purpose so long as Arcflash Labs is willing and able to repair or replace any defective product, or refund the purchase price, in the prescribed manner. In the event Arcflash Labs fails to provide the Buyer with free repair or replacement, or refund the purchase price as aforesaid, Arcflash Labs’...
- Page 3 60v cordless drill batteries. The included battery can provide power for over 300 shots before needing to recharge. The rate of fire of the EMG-02 (up to 8 rounds/sec) is limited by the discharge rate of the lithium ion battery.
- Page 4 1 foot may cause irreversible damage to the gun, fire, explosion, electrical shock or venting of toxic gas from the battery or capacitors. If the EMG-02 is dropped or exposed to water: discontinue use immediately and return the gun to its manufacturer for repairs.
-
Page 5: Overview Of Components
Fastener (not user serviceable) The EMG-02 is a fully automatic electromagnetic gun – its core component is a sequence of optically gated driver solenoids. As a projectile passes through the barrel, it triggers optical gates which send signals back to the microcontroller. The microcontroller quickly interprets these signals and directs the coils to turn on in a precise sequence. - Page 6 While its muzzle energy is comparable to low end air rifles (around 10-20 joules or 7.5- 15 ft-lbs), it should be treated the same way as a firearm. All armatures fired from the EMG-02 have the capacity to penetrate 10% ballistics gel between 2-4” and could result in potentially lethal injuries.
-
Page 7: Discharge Resistor
2.4 Main fuse The main fuse of the EMG-02 is a 40A automotive fuse which acts as a protection against certain types of over-current. If the gun shuts down and fails to restart, a user may attempt to replace the fuse if it has blown. -
Page 8: Main Switch
The microcontroller will charge the capacitors through the charging cable. There are two high current relays inside the EMG-02 which toggle the flow of current during startup. The user may hear several clicks as the unit starts up. The first relay toggles the flow of charge into or out of the capacitor through the resistor and charging cable, the second relay toggles the main high current bus between the capacitor/battery and coils. - Page 9 To adjust the firing mode, simply press inward on the firing mode selector until the desired firing mode is selected. NOTE: The firing mode selector button may look slightly different on later batches of the EMG-02. Below the firing mode selector, there is a toggle switch which activates the laser at the front of the barrel.
- Page 10 2.7 Battery - The EMG-02 uses a large Lithium Ion battery. Large lithium batteries can catch fire or release gas if stored improperly. Always store in a cool, dry environment. The EMG-02 uses a Lithium Ion battery. You know the drill. Big scary battery. Hazards include shock, fire, explosion or venting of toxic gas.
-
Page 11: Operation
Usage of improper armatures in magazines could result in misfires. 2.9 Capacitor - The EMG-02 contains a large 0.33F capacitor capable of storing up to 600J of energy - The capacitor may become unsafe if struck, cut, or severely dented The EMG-02 contains a large electrolytic capacitor at the rear which is used as a buttstock for the accelerator. - Page 12 - ALWAYS ENSURE THE POWER SWITCH IS SET TO OFF BEFORE INSERTING THE BATTERY. - DO NOT INSERT A LOADED MAGAZINE UNTIL THE GUN IS POWERED ON AND POINTED IN A SAFE DIRECTION. 1. Insert battery into battery socket 2. Toggle the main switch from the OFF position to the ON position. 3.
-
Page 13: Inserting A Magazine
3.2 Inserting a magazine 1. Always ensure the gun is powered up and pointed in a safe direction before inserting a magazine. There is no slide or chamber on the EMG-02. The active round in the magazine itself acts as the chambered round. - Page 14 3. Ensure the magazine is properly seated and the armature is properly aligned with the barrel (yellow tube). If the silver armature is not visible through the front view port (or is not properly aligned with the tube) after a magazine has been inserted, the round may not feed properly during the first shot but should still feed properly on subsequent shots.
-
Page 15: Battery Charging
Battery Release 5. Replace the EMG-02 and battery in its included carrying case. 3.4 Battery Charging 1. Unpack the charger and connect the balance charging unit to the AC power supply. -
Page 16: Hardware Specifications
02 software is expressly discouraged and will immediately void any express or implied warranties. Any attempt to modify the software may render the gun unusable or unsafe. Arcflash Labs, LLC assumes absolutely no responsibility for units which have had their software modified by the end user. - Page 17 17 | P a g e...
Need help?
Do you have a question about the EMG-02 and is the answer not in the manual?
Questions and answers