INDEX INSTALLATION Safety Information Recommendations before loading & plugging in the beverage cooler Grounding Instructions Assembly Levelling Your Beverage Cooler OPERATING YOUR BEVERAGE COOLER Defrosting/hygrometry/condensation/ventilation Temperature setting Beverage Cooler Control panel Cooling Indicator light Interior Light Installing Stainless Steel Handle Power Failures and Operation Anomalies CARE AND MAINTENANCE Clean the condenser...
This beverage cooler should only be use for the storage of beverages. It must not be used to store food. Euro Appliances offers no guarantee for our beverage cooler if it is being used for any purpose other than that for which it was specially designed. Euro Appliances is not responsible or liable for any spoilage or...
Page 4
Recommendations before loading & plugging in the beverage cooler Be unencumbered and well ventilated; Be well away from any heat source and direct sunlight or rain; Not be too damp (laundry, pantry, bathroom, garage and basement, etc.); Have a flat, level and dry floor; Have a standard and reliable electricity supply (10A General purpose outlet properly earthed).
Page 5
where there is frequent lightning, it is advisable to use surge protectors. Improper use of the grounding plug can result in the risk of electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
OPERATING YOUR BEVERAGE COOLER 1. Turning on your beverage cooler. Plug in and switch on the beverage cooler by pressing on the power button for a few seconds. When you use the beverage cooler for the first time (or restart the beverage cooler it has been switch off for a long time), there will be a few degrees variance between the temperature you have selected and the one indicated on the LED readout.
Page 7
Important Do not pull out more than one loaded rack at a time as this may cause the beverage cooler to tilt forward. Do not cover the metal racks with aluminum foil or other materials, as it will obstruct air circulation. Do not move your beverage cooler while it is loaded with beverages.
Page 8
Temperature Setting Depending on the loading and settings chosen, it takes 24 hours for the beverage cooler temperature to stabilize. During this time, the LED temperature display may seem to move erratically. This is a normal process. This process occurs whenever the setting is modified and/or whenever large amounts of cans or bottles are added to the beverage cooler.
INSTALLING STAINLESS STEEL HANDLE This beverage cooler includes a stainless steel handle that is required to operate this unit. To install the handle please follow the instruction below 1. Pull away the door gasket in the area where the handle is to be installed – you can see two designated holes for handle installation.
Page 10
Power Failures And Operation Anomalies In the event of a power interruption, all previous temperature settings are automatically erased and the beverage cooler will revert to a preset temperature setting. Most power failures are corrected within a short period of time. A loss of power for an hour or two will not affect your beverage cooler’s temperature. To avoid sudden change of temperature while the power is off, you should avoid opening the door.
CARE AND MAINTENANCE Clean the condenser The condenser must be kept clean and free of dust at all times. It is recommended that the cleaning routine be conducted at intervals appropriate to the speed of accretion of dust on the condenser. Failure to keep the condenser clean will damage the refrigeration system and invalidate the warranty.
Page 12
Recommended Cleaning Product Switch off and disconnect from the power supply before cleaning Clean the interior of the appliance using the recommended products in accordance with local hygiene laws and regulations. Do not use abrasive cleaning agents, which may scratch and harm the delicate interior finishes of your appliance.
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE Beverage cooler does not operate Not plugged in. The appliance is turned off. The circuit breaker has tripped or a fuse has Blown. Beverage cooler is not cold enough. Check the temperature control setting. External environment may require a higher setting. The door is opened too often.
TECHNICAL SPECIFICATIONS EA60 Series Stainless Steel Beverage Cooler Item Number EA60WFSX2L EA60WFSX2R EA60SDSXL EA60SDSXR Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stype Glass Door Glass Door Solid Door Solid Door Left Door open Right Door open Left Door Open...
Page 15
EA60 Series Black Beverage Cooler Item Number EA60WFBL EA60WFBR EA60WSDBL EA60WSDBR Black Frame Black Frame Black Frame Black Frame Stype Glass Door Glass Door Solid Door Solid Door Left Door open Right Door open Left Door Open Right Door Open Cooling System Compressor Cooling Compressor Cooling...
Page 16
EA90 Series Beverage Cooler Item Number EA90SDSX EA900WFSX2 EA900WFBL EA900WSDB Stainless Steel Stainless Steel Black Frame Black Frame Stype Solid Door Glass Door Glass Door Solid Door Cooling System Compressor Cooling Compressor Cooling Volumn 208L 208L Climate Glass Rated Voltage AC220V-240V / 50Hz AC220V-240V / 50Hz Rated Current...
Need help?
Do you have a question about the EA60SDSXL and is the answer not in the manual?
Questions and answers