Download Print this page

Hitachi CP-X200 Technical Information

Hitachi cp-x200: supplementary guide.
Hide thumbs

Advertisement

Projector
CP-X200/CP-X300/CP-X400
User's Manual (detailed)
Technical
Example of PC signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz)
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
024 x 768
024 x 768
024 x 768
024 x 768
52 x 864
280 x 960
280 x 024
280 x 024
280 x 024
600 x 200
280 x 768
400 x 050
NOTE
• Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a PC.
• Some PCs may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(600x200), the signal will be converted to the projector's panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• Automatically adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.
37.9
3.5
37.9
37.5
43.3
35.2
37.9
48.
46.9
53.7
49.7
48.4
56.5
60.0
68.7
67.5
60.0
64.0
80.0
9.
75.0
47.7
65.2
Rating
85.0
VESA
59.9
VESA
72.8
VESA
75.0
VESA
85.0
VESA
56.3
VESA
60.3
VESA
72.2
VESA
75.0
VESA
85.
VESA
74.5
60.0
VESA
70.
VESA
75.0
VESA
85.0
VESA
75.0
VESA
60.0
VESA
60.0
VESA
75.0
VESA
85.0
VESA
60.0
VESA
60.0
VESA
60.0
VESA
Signal mode
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 6" mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
52 x 864 (75Hz)
280 x 960 (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
UXGA (60Hz)
W-XGA (60Hz)
SXGA+ (60Hz)


Advertisement

   Related Manuals for Hitachi CP-X200

   Summary of Contents for Hitachi CP-X200

  • Page 1

    • Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. • Although the projector can display signals with resolution up to UXGA (600x200), the signal will be converted to the projector’s panel resolution before being displayed.

  • Page 2

    Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in IMAGE menu. Back porch (B) Active video (C) Data H.

  • Page 3

    Connection to the ports COMPUTER IN1, D-sub 5pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. Signal: TTL level (positive/negative) • Composite sync. Signal: TTL level Signal Video Red Video Green Video Blue (No connection) Ground Ground Red...

  • Page 4

    Connection to the ports (continued) COMPONENT VIDEO RCA jack x3 • System: 525i(480i), 525p(480p), 625i(576i), 750p(720p),25i(080i) Port Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite Pb/Cb Component video Pb/Cb, 0.7±0.1Vp-p, 75Ω terminator Pr/Cr Component video Pr/Cr, 0.7±0.1Vp-p, 75Ω terminator S-VIDEO Mini DIN 4pin jack Color signal 0.286Vp-p (NTSC, burst), 75Ω...

  • Page 5

    SCART connector (jack) SCART cable (plug) To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex.. For more reference, please consult your dealer. Connection to the ports (continued) RCA plugs...

  • Page 6

    Connection to the ports (continued) USB B type jack Signal  +5V 2 - Data 3 + Data 4 Ground CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the following page. Signal (No connection) Signal (No connection) Ground...

  • Page 7: Communications Setting

    Connecting the cable Turn off the projector and the computer. Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-232C cable (cross). Use the cable that fulfills thespecification shown in the previous page.

  • Page 8

    • Provide an interval of at least 40ms between the response code and any other code. • The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.

  • Page 9

    RS-232C communication command table Names  Operation Type Power Input Source COMPUTER1 COMPUTER2 COMPONENT S-VIDEO Error Status BRIGHTNESS Increment Decrement BRIGHTNESS Reset Execute CONTRAST Increment Decrement CONTRAST Reset Execute PICTURE MODE NORMAL CINEMA DYNAMIC BOARD(BLACK) BOARD(GREEN) WHITEBOARD DAYTIME GAMMA #1 DEFAULT #1 CUSTOM #2 DEFAULT #2 CUSTOM #3 DEFAULT #3 CUSTOM #4 DEFAULT #4 CUSTOM #5 DEFAULT #5 CUSTOM #6 DEFAULT...

  • Page 10

    Command Control via the Network (continued) RS-232C communication command table (continued) Names  Operation Type User Gamma Pattern 9 step gray scale 15 steps gray scale User Gamma Point 1 Increment Decrement User Gamma Point 2 Increment Decrement User Gamma Point 3 Increment Decrement User Gamma Point 4 Increment Decrement User Gamma Point 5 Increment Decrement User Gamma Point 6 Increment Decrement User Gamma Point 7 Increment Decrement User Gamma Point 8 Increment Decrement COLOR TEMP CUSTOM-1 (HIGH) CUSTOM-2 (MID)

  • Page 11

    RS-232C communication command table (continued) Names  Operation Type COLOR TEMP GAIN B Increment Decrement COLOR TEMP  OFFSET R Increment Decrement COLOR TEMP  OFFSET G Increment Decrement COLOR TEMP  OFFSET B Increment Decrement COLOR  Increment Decrement COLOR Reset Execute TINT Increment Decrement TINT Reset Execute SHARPNESS Increment Decrement SHARPNESS Reset Execute MY MEMORY Load MY MEMORY Save PROGRESSIVE TURN OFF VIDEO NR ASPECT...

  • Page 12

    Command Control via the Network (continued) RS-232C communication command table (continued) Names  Operation Type OVER SCAN Increment Decrement OVER SCAN Reset Execute V POSITION Increment Decrement V POSITION Reset Execute H POSITION Increment Decrement H POSITION Reset Execute H PHASE Increment Decrement H SIZE Increment Decrement H SIZE Reset Execute AUTO ADJUST Execute COLOR SPACE SMPTE240 COMPONENT COMPONENT SCART RGB...

  • Page 13

    RS-232C communication command table (continued) Names Operation Type COMPUTER IN1 SYNC ON G ON SYNC ON G OFF COMPUTER IN2 SYNC ON G ON SYNC ON G OFF KEYSTONE V Increment Decrement KEYSTONE V Reset Execute AUTO KEYSTONE  Execute EXECUTE WHISPER NORMAL WHISPER MIRROR NORMAL H:INVERT V:INVERT H&V:INVERT VOLUME- COMPUTER1 Increment Decrement VOLUME- COMPUTER2 Increment Decrement VOLUME- COMPONENT Increment Decrement VOLUME-S-Video Increment...

  • Page 14

    Command Control via the Network (continued) RS-232C communication command table (continued) Names  Operation Type AUDIO-COMPUTER1 Set AUDIO-COMPUTER2 Set AUDIO-COMPONENT Set AUDIO-S-VIDEO AUDIO-VIDEO IR REMOTE FREQ. NORMAL IR REMOTE FREQ. HIGH (continued on next page) Header AUDIO1 BE  EF AUDIO2 BE  EF AUDIO3 BE  EF Turn off BE  EF BE  EF AUDIO1 BE  EF AUDIO2 BE  EF...

  • Page 15

    RS-232C communication command table (continued) Names  Operation Type LANGUAGE ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO NEDERLANDS PORTUGUÊS SVENSKA PУCCKИЙ MENU POSITION H Increment Decrement MENU POSITION H Reset Execute MENU POSITION V Increment Decrement MENU POSITION V Reset Execute BLANK MyScreen ORIGINAL BLANK On/Off TURN OFF TURN ON START UP MyScreen ORIGINAL TURN OFF MyScreen LOCK TURN OFF TURN ON MESSAGE TURN OFF TURN ON...

  • Page 16

    Command Control via the Network (continued) RS-232C communication command table (continued) Names  Operation Type AUTO KEYSTONE AUTO ON AUTO OFF Increment Decrement LAMP TIME LAMP TIME Reset Execute FILTER TIME FILER TIME Reset Execute MY BUTTON-1 COMPUTER1 COMPUTER2 COMPONENT S-VIDEO VIDEO INFORMATION AUTO KEYSTONE EXECUTE MY MEMORY PICTURE MODE FILTER RESET VOLUME + VOLUME - MY BUTTON-2 COMPUTER1 COMPUTER2 COMPONENT S-VIDEO VIDEO...

Comments to this Manuals

Symbols: 0
Latest comments: