Dawnco DIGISAT PLUS Quick Start Manual

DIGISAT PLUS DIGISAT PLUS DIGISAT PLUS
TURNING THE UNIT ON
Open the Velcro flap and remove the DC power plug. Open the Velcro flap and remove the DC power plug. Open the Velcro flap and remove the DC power plug.
Close the Velcro flap. Close the Velcro flap. Close the Velcro flap.
Insert the small female plug from the battery pack into Insert the small female plug from the battery pack into Insert the small female plug from the battery pack into
the input connector on the bottom of the DIGISAT. the input connector on the bottom of the DIGISAT. the input connector on the bottom of the DIGISAT.
Turn the DIGISAT ON by pressing the power button one Turn the DIGISAT ON by pressing the power button one Turn the DIGISAT ON by pressing the power button one
time. time. time.
After tracking the satellite antenna, press & hold the After tracking the satellite antenna, press & hold the After tracking the satellite antenna, press & hold the
power button to turn the DIGISAT battery pack OFF. power button to turn the DIGISAT battery pack OFF. power button to turn the DIGISAT battery pack OFF.
The DIGISAT can operate one LNBF (dual port type) up The DIGISAT can operate one LNBF (dual port type) up The DIGISAT can operate one LNBF (dual port type) up
to two hours on a single charge. to two hours on a single charge. to two hours on a single charge.
CHARGING THE BATTERY PACK
Plug either AC or DC charger into the male pigtail connector. From a Plug either AC or DC charger into the male pigtail connector. From a Plug either AC or DC charger into the male pigtail connector. From a
fully discharged state, the AC charger will charge the 400 mA fully discharged state, the AC charger will charge the 400 mA fully discharged state, the AC charger will charge the 400 mA
battery pack in about 12 hours. Do not continue charging with battery pack in about 12 hours. Do not continue charging with battery pack in about 12 hours. Do not continue charging with
the wall charger beyond that time. The DC charger will charge the wall charger beyond that time. The DC charger will charge the wall charger beyond that time. The DC charger will charge
the battery pack fully in 2 to 4 hours. the battery pack fully in 2 to 4 hours. the battery pack fully in 2 to 4 hours.
Plug into 110vAC wall
outlet socket. A discharged
pack can be fully restored
in about 12 hours. DO NOT
leave the pack connected to
the AC charger indefinitely.
Plug into 12vDC (auto lighter) or accessory socket.
SIMPLIFIED OPERATING INSTRUCTIONS
1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and 1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and 1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and
connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT. connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT. connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT.
2) Turn the DIGISAT on as illustrated above. 2) Turn the DIGISAT on as illustrated above. 2) Turn the DIGISAT on as illustrated above.
3) The audible squawker circuit can be turned ON by pressing the left and right yellow 3) The audible squawker circuit can be turned ON by pressing the left and right yellow 3) The audible squawker circuit can be turned ON by pressing the left and right yellow
buttons simultaneously. buttons simultaneously. buttons simultaneously.
Operation and Maintenance Operation and Maintenance Operation and Maintenance
DO NOT continue DC charging beyond 4 hours.
DG2PLUS
DG-2 DG2PLUS DG-2 D
DC Power
Plug