Advertisement
Example 2:
Voltage Full Scale Setting
(Analogue Parameters)
(Current Output Type
(Analogue Operation range
setting
(PERC)
PERC
For 4 - 20mA
For 4 - 20mA
Factory Set Values
Current Full Scale Setting
Shunt Resistance mV Setting : 60mV
Voltage Full Scale Setting
1000V Password setting: 0000
: 9600
Baud Rate
: 1
Stop Bits
: no
Parity
: 1
No
Device
Over Voltage Set Value ( Volt Over Val)
Over Voltage Alarm Permit (Volt Over EnbL)
Over Voltage Alarm Mode Setting (Volt Over tYPE)
Over Voltage Delay Time (Volt Over dELy)
Over Voltage Mistake Repair Time (Volt Over dLy0)
Over Voltage Hysteresis Value (Volt Over HySt)
Low Voltage Set Value (Volt Undr Val)
Low Voltage Alarm Permit (Volt Undr EnbL)
Low Voltage Alarm Mode Setting (Volt Undr tyPE)
Low Voltage Delay Time (Volt Undr dELy)
Low Voltage Mistake Repair Time (Volt Undr dLy0)
Low Voltage Hysteresis Value (Volt Undr HySt)
Over Current Set Value ( Curr Over Val)
Over Current Alarm Permit (Curr Over EnbL)
Over Current Alarm Mode Setting (Curr Over tYPE)
Over Current Delay Time (Curr Over dELy)
Over Current Mistake Repair Time (Curr Over dLy0) : 10 sec
Over Current Hysteresis Value (Curr Over HySt) : 30 %
Low Current Set Value (Curr Undr Val)
Low Current Alarm Permit (Curr Undr EnbL)
Low Current Alarm Mode Setting (Curr Undr tyPE)
Low Current Delay Time (Curr Undr dELy)
Low Current Mistake Repair Time (Curr Undr dLy0)
Low Current Hysteresis Value (Curr Undr HySt)
Over Power Set Value ( Povr Over Val)
Over Power Alarm Permit (Povr Over EnbL)
Over Power Alarm Mode Setting (Povr Over tYPE)
Over Power Delay Time (Povr Over dELy)
Over Power Mistake Repair Time (Povr Over dLy0)
Over Power Hysteresis Value (Povr Over HySt)
Low Power Set Value (Povr Undr Val)
Low Power Alarm Permit (Povr Undr EnbL)
Low Power Alarm Mode Setting (Povr Undr tyPE)
Low Power Delay Time (Povr Undr dELy)
Low Power Mistake Repair Time (Povr Undr dLy0)
Low Power Hysteresis Value (Povr Undr HySt)
)
= 300 V
)
=
Current
(A)
)
= 4 - 20
(mA)
))
= =
(upper limit % ) = 100 %
( lower limit % ) = 0 %
(Measured Value)
(Full Scale Value )
I
=
4 +
(analogue)
Upper Limit (%) - Lower Limit (%)
I
=
4 +
(analogue)
: 100A
: 300V /
Measurement Value
300 V
220 V
0 V
x 100% - Lower Limit (%)
( 220 )
x 100 - 0
( 300 )
100 - 0
: 300V / 1000V
RELAY CONTACT POSITION
: no (disables)
Remote Access Permit : oFF (Access disabled)
: alarm mode
: 10 sec
: 10 sec
: 30%
: 150V / 500V
: no (disabled)
: alarm mode
: 10 sec
: 10 sec
: 30 %
Analogue Output Permit
Parameter
: 100A
Output type
: no (disabled)
Operation Range Setting
: alarm mode
PERC % upper limit
: 10 sec
PERC % lower limit
: 50A
: no (disabled)
: alarm mode
: 10 sec
: 10 sec
: 30 %
: 30.000VA / 100.000VA
: no (disabled)
: alarm mode
: 10 sec
: 10 sec
: 30 %
: 15.000VA / 50.000VA
: no (disabled)
: alarm mode
: 10 sec
: 10 sec
: 30 %
Analogue Output Value
20 mA
15.72mA
4 mA
x 16mA
= 15,73mA
x 16
: nO (normally ON)
Pulse Type: OFF
: 1kWh
Deal
Pulse Time: 100ms
:no (disabled)
:VOLT (voltage measurement):
0 – 10 V
: PERC
: +100%
: 0%
Advertisement
