2.2 BATTERY SPECIFICATION Item Specification Battery Type LiFePO4 Nominal Voltage 51.2V Nominal Capacity 120Ah Nominal Energy 6.144kWh Standard Charge Voltage 56.0V Recommended Floating Charge Voltage 54.4V Maximum Continuous Charge Current 120A Maximum Continuous Discharge Current 120A Peak Discharge Current (3s) 300A Maximum Continuous D ischarge P ower Peak Discharge Power (3s)
4. INSTALATION PREPARATION 4.1. CHECK THE PACKING LIST Parts Quantity 1 @unit Modules communication cable_RJ45+RJ45_150mm 1 @unit Terminal@matching@resistance_120 1 @unit Wall mounting bracket handle 2 units units Expanding screw M8*60 4.2 PRODUCT IMAGE...
Page 10
Start Read the manual Site selection Install wall mounting bracket Install the battery pack Connect the cables Commission Troubleshooting Normally r unning?
5.1 INSTALATION LOCATION 5.1.1 ENVIRONMENT REQUIREMENT Application S cenarios Residence Indoor and place away from strong Operating Environment electromagnetic radiation -20~55 Discharge Temperature IP G rade IP55 Short -term (≤ 1month): -20~45 °C (-4 ~ 113°F) Storage Temperature Long -term (≥ 1month): 15~35 °C (59~95 °F ) Operating Humidity 0 ~ 85% 100A @ ≤...
Page 12
T op 200 mm (8 inches) Wall or other Wall or other equipment equipment 200 mm 200 mm (8 inches) (8 inches) 400 mm (16 inches) Floor ATTENTION t 。 。@@ 。 @。 。 。 。 。 。 。@ 。 。...
Page 15
. . CONNECTING ORDER Process No. Operation Set the module communication address by the DIP Switch. @ Connect the Module COM cable (RJ45 connector) between battery modules. Connect the inverter COM Cable between the battery and the inverter. Connect the battery Power Cable to the the Bus-wire Connect the Bus-wire to the inverter.
Page 16
. . SET THE ADDRESS OF THE DIP SWITCH DIP@ @ DIP@ DIP Switch Module number Single module Master module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module Slave module...
Page 17
. . CAN & RS COMMUNICATION PORT PIN DEFINITION RS485 CAN 1 CAN 2 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 RS485 port Both CAN port s Pin No.
. . OPERATION @ Start-up:@ @ @ @ Running:@ Alarm*:@ Turn-Off:@ Items Description 3.60±0.03V (Not displayed on Over-charge alarm for each cell LCD or alarm LED) 3.75±0.03V, Delay time:1s (Not Over-charge protection for each cell displayed on LCD or alarm LED) Over-charge release for each cell 3.40±0.03V...
Page 19
discharge Over-discharge protection for each cell 2.70±0.03V for 1±0.5s Over-discharge release for each cell 3.00±0.03V Over-discharge alarm for total voltage 46.4V±0.5V Over-discharge protection for total voltage 43.2V±0.5V for 1±0.5s Over-discharge release for total voltage 48V±0.5V Over-discharge release method Charge to recovery Charge over current alarm 135±5A Charge over current protection...
Page 20
. . BATTERY INFORMATION DISPLAY LCD CONTROL PANEL The control panel displays a variety of useful information regarding the operation of your system, such the voltage, state of charge and temperature. SUPPLEMENTARY INSTRUCTIONS Display Indicator Note Battery voltage Residual energy Negative value indicates discharging.
The battery will light these indicators when a warning or alarm condition occurs: HV = Battery High Voltage LV = Battery Low Voltage Alarm HT = Battery High Temperature LT = Battery Low Temperature OC = Charge or Discharge Over Current SC = Short Circuit .
Page 22
1.Check the D IP switch and ensure its configured properly. Note: If the problem is still not resolved after troubleshooting, please contact the manufacturer below. Contact Information CANBAT TECHNOLOGIES INC. Address: 1285 W Broadway #600 Vancouver, BC V6H 3X8 Web: www.canbat.com...
TECHNICAL SUPPORT If you have technical questions about your Canbat battery, please contact the original place of purchase or Canbat Technologies Inc. directly: info@canbat.com +1 (778) 358-3925 www.canbat.com...
Page 24
Canbat Technologies Inc. provides customers with the highest quality and safest lithium iron phosphate ba�ery products. All rights reserved. Canbat Technologies Inc. is not liable for damages that may result from any informa�on provided in or omi�ed from this publica�on, under any circumstances. Failure to follow Canbat installa�on guidelines may invalidate the warranty. Canbat...