Advertisement
Quick Links
User
User
User
User Manual
Multi-beam
Multi-beam
Multi-beam
Multi-beam Active
1 1 1 1 、 Product
Product
Product
Overview
Overview
Product Overview
Overview
Solar-powered multi-beam active wireless infrared light walls for engineering
applications is a new-type hi-tech environmentally- friendly product and has obtained
national patent. It applies sun's UV rays to supply power and charge for itself, and
adopts the wireless signal transmission device to transmit alarm signal instead of
power cable and signal line. It is widely installed in houses, schools, workshops and
perimeter fencing of residential quarters etc.
2 2 2 2 、 Name
Name
Name
Name of of of of Parts
Parts
Parts
Parts
Manual
Manual
for
for
Manual for
for Solar-Powered
Active
Active Wireless
Active
Light
Light
Light
Light Walls
HB-T001Q3
HB-T001Q3
HB-T001Q3
HB-T001Q3
HB-T001
HB-T001
HB-T001R R R R 3 3 3 3
HB-T001
Solar-Powered
Solar-Powered
Solar-Powered
Wireless
Infrared
Wireless Infrared
Wireless
Infrared
Infrared
Walls
Walls
Walls
Advertisement
Related Manuals for Saferhomee HB-T001Q3
Summary of Contents for Saferhomee HB-T001Q3
- Page 1 Active Wireless Wireless Wireless Infrared Infrared Infrared Light Light Walls Walls Light Light Walls Walls HB-T001Q3 HB-T001Q3 HB-T001Q3 HB-T001Q3 HB-T001 HB-T001 HB-T001R R R R 3 3 3 3 HB-T001 1 1 1 1 、 Product Product Product Overview Overview...
- Page 2 3 3 3 3 、 Installation Installation Precautions Installation Installation Precautions Precautions Precautions Note 1: Never inst all light walls at an inclined angle. Note 2: Make sure that there is no obstacle between the transmitting terminal and the receiving terminal. Note 3: Multiple light walls shall be installed for long-distance alarm in accordance with the installation instructions shown in the above-mentioned figure to avoid...
- Page 3 transmission distance. Other Other Important Important Precautions Precautions Other Other Important Important Precautions Precautions ① Before installation, remove the plastic film on the solar panel of the light wall. ② Never install this light wall near door access systems, passages, areas prone to trigger an alarm, or areas which could trigger an alarm more than 50 times per 24 hours.
- Page 4 multi-beam light wall is normally powered off. When the “ON/OFF ”key is pressed again, it means the light wall is turned off if there are two “Beep, Beep” sound prompts. Other Other Other Other Precautions Precautions Precautions Precautions ①In normal operation state, when the “ON/OFF”key is pressed twice, a turn-off signal will be sent after an alarm signal is transmitted.
-
Page 5: Calibration Precautions
Determine a suitable installation height, make holes in wall with a percussion drill, and then fasten iron brackets in wall with metal screws. Try to keep two brackets respectively for transmitting terminal and the receiving terminal of the light wall in the same horizontal height. - Page 6 ①Verify if the detector is normally operating by confirming if the indicator lamp of the light wall normally flashes. ②Hole Block-up： a) The light wall does not alarm when two infrared light holes at the upper end of the light wall are blocked up. b) The light wall does not alarm when two infrared light holes at the lower end of the light wall are blocked up.
- Page 7 Active Active Wireless Wireless Infrared Infrared Technical Technical Parameters Parameters Solar-Powered Solar-Powered Multi-beam Multi-beam Active Active Wireless Wireless Infrared Infrared Light Light Walls Walls Light Light Walls Walls Infrared Distance 100m Wireless Transmitting HB-T001Q3 100m Distance HB-T001R3 Wireless Transmitting FM:433MHz...
- Page 8 Frequency Maximum alarm times Not more than 50 times in 24 hours Battery Capacity 500mAh (Transmitting Terminal), 1000mAh (Receiving Terminal) -30 ℃ ~70 ℃ Working environment temperature range Number of infrared 3beams beams Operating Voltage 3.3V Transmitting terminal ≤ 0.5mA, receiving terminal ≤ Static Operating Current 0.5mA Infrared light frequency...