Advertisement
3.
INSTALLATION
p WARNING! Before connecting the thermostat, make sure that the power supply to the heater is not connected.
3.1
Placement of the thermostat.
Note:
The thermostat should be placed in a position away from doors, windows and approx 1.5mtr from the floor.
3.1.1
Remove the front cover from the thermostat base by releasing the clip using a screwdriver (fig.2.).
3.1.2
Remove the breakout from the base using a suitable pair of pliers to allow the cable to recess the base.
This will enable the base to sit flush against the wall.
3.1.3
Fix the base to the wall using the provided holes and secure it by means of suitable screws.
3.1.4
Replace the cover.
fig.1.
Warning
lamp
Temperature
setting knob
ON/OFF switch
4. OPERATION
4.1
Install the thermostat by removing the socket cover on the heater panel (Fig. 3.) and inserting the thermostat plug into the socket.
4.1.1
Plug the heater into the mains socket (230V ~ 50Hz single phase).
(THE HEATER MUST BE EARTHED.)
4.1.2
Set the thermostat ON/OFF switch to ON (Fig.1.c) and the temperature knob (Fig.1.a) to maximum and start the heater.
4.1.3
When the heater is running you may adjust the temperature by rotating the temperature knob to the desired temperature.
4.1.4
To turn off your AB heater, switch off the thermostat and follow your heater’s instructions to shut down the heater.
thermostat socket
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following EEC
standards and directives.
The construction file for this product is held by the Manufacturer
and may be inspected, by a national authority, upon request to Jack Sealey Ltd
REMOTE THERMOSTAT FOR AB HEATERS
Model ABT04
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
fig.2.
Fig. 3.
1st November 2004
Signed by Mark Sweetman
01284 757500
Web address: www.sealey.co.uk
01284 703534
E-mail: sales@sealey.co.uk
ABT04 - 1 - 101104
3.
INSTALLATION
p WARNING! Before connecting the thermostat, make sure that the power supply to the heater is not connected.
3.1
Placement of the thermostat.
Note:
The thermostat should be placed in a position away from doors, windows and approx 1.5mtr from the floor.
3.1.1
Remove the front cover from the thermostat base by releasing the clip using a screwdriver (fig.2.).
3.1.2
Remove the breakout from the base using a suitable pair of pliers to allow the cable to recess the base.
This will enable the base to sit flush against the wall.
3.1.3
Fix the base to the wall using the provided holes and secure it by means of suitable screws.
3.1.4
Replace the cover.
fig.1.
Warning
lamp
Temperature
setting knob
ON/OFF switch
4. OPERATION
4.1
Install the thermostat by removing the socket cover on the heater panel (Fig. 3.) and inserting the thermostat plug into the socket.
4.1.1
Plug the heater into the mains socket (230V ~ 50Hz single phase).
(THE HEATER MUST BE EARTHED.)
4.1.2
Set the thermostat ON/OFF switch to ON (Fig.1.c) and the temperature knob (Fig.1.a) to maximum and start the heater.
4.1.3
When the heater is running you may adjust the temperature by rotating the temperature knob to the desired temperature.
4.1.4
To turn off your AB heater, switch off the thermostat and follow your heater’s instructions to shut down the heater.
thermostat socket
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following EEC
standards and directives.
The construction file for this product is held by the Manufacturer
and may be inspected, by a national authority, upon request to Jack Sealey Ltd
REMOTE THERMOSTAT FOR AB HEATERS
Model ABT04
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
fig.2.
Fig. 3.
1st November 2004
Signed by Mark Sweetman
01284 757500
Web address: www.sealey.co.uk
01284 703534
E-mail: sales@sealey.co.uk
ABT04 - 1 - 101104
Advertisement
