Advertisement
Quick Links
KNOW YOUR PRODUCT
12V BATTERY
& ALTERNATOR
TESTER
• ANALYSE BATTERY,
ALTERNATOR &
STARTER CRANKING
CONDITION
• TEST BATTERIES UP TO
2000 CCA
INSTRUCTION MANUAL
WARNING: Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference.
0222
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Full Boar FBCBA-2000
- Page 1 KNOW YOUR PRODUCT 12V BATTERY & ALTERNATOR TESTER • ANALYSE BATTERY, ALTERNATOR & STARTER CRANKING CONDITION • TEST BATTERIES UP TO 2000 CCA INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
-
Page 2: Know Your Product
SPECIFICATIONS - MODEL NO. FBCBA-2000 KNOW YOUR PRODUCT (cont.) 1. LCD Screen Input: 8V to 20V Indicates voltage, CCA, general battery condition and test results. Capacity: 100-2000 CCA (20-1000 CCA for *Li-ion battery) Suitable for: 12V Lead acid, AGM, EFB, GEL & *Li-ion batteries 2. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION Congratulations on purchasing a Full Boar 12V Battery SPECIFICATIONS............Page 02 & Alternator Tester. The Full Boar Battery & Alternator KNOW YOUR PRODUCT...........Page 02 Tester FBCBA-2000 is designed for performing a thorough test of the battery condition, alternator charge INTRODUCTION............Page 05... - Page 4 BATTERY TESTER SAFETY WARNINGS BATTERY TESTER SAFETY WARNINGS (cont.) -Personal Safety WARNING! Save all warnings and instructions for future - Wear ANSI-approved safety goggles and protective gloves during set up and use reference. of the Battery Tester. - Test in a well ventilated area. Explosive gases may be produced during testing. WARNING! Read all safety warnings and all instructions.
-
Page 5: General Information
BATTERY TESTER SAFETY WARNINGS (cont.) GENERAL INFORMATION Battery system standard description - Do not smoke or have open flames near the battery. - The warnings and precautions discussed in this manual cannot cover all possible CCA: Cold Cranking Amps. conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, BCI: Battery Council International standard. -
Page 6: Operation
OPERATION KNOW YOUR PRODUCT OPERATION (cont.) Connecting and disconnecting from a vehicle battery System setup 1. Connect the battery tester to the battery, following the instructions specified in WARNING! Read and understand the warnings before setup and the "Connecting and disconnecting from a vehicle battery" section. testing. - Page 7 5. Print 5. Italian 6. System Setup 6. Dutch System Setup System Setup 1. Language Fn Setting OPERATION (cont.) Main Menu System Setup OPERATION (cont.) Language 2. Fn settings 1. Language 1. Voltmeter 3. Contrast 1. Battery Test 1. Language 1.
- Page 8 OPERATION (cont.) OPERATION (cont.) 3. From the Main Menu, using the up button 7. Use the up and down buttons to select the actual system standard (SAE, (8) and down buttons (6) select Battery Test Main Menu Battery Test DIN, IEC, EN, CA, MCA, JIS, BCI, CCA, GB), press enter button (7) to confirm Battery Type (fig.
- Page 9 OPERATION (cont.) OPERATION (cont.) Cranking test 11. Battery test results includes five types as follows (fig. 18): With the battery terminal clamps correctly connected and before having your Battery Test assistant start the engine, turn off all vehicle accessory loads such as lights, air - Battery good conditioning, radio etc.
- Page 10 6. System Setup 2. Cranking Test 3. Charging Test 4. Review Data 5. Print 6. System Setup Cranking Test OPERATION (cont.) OPERATION (cont.) Start Engine Cranking Test Testing the charging system 4. When the test is completed, the LCD screen (1) will show the test results including the cranking voltage.
- Page 11 Charging Test Charging Test Unloaded 14.49V Unloaded 15.36V Loaded 14.18V Loaded 14.18V OPERATION (cont.) OPERATION (cont.) Ripple 78mV Ripple 78mV VOLTAGE NORMAL VOLTAGE HIGH Review data - Charging Volt: Low (fig. 27). Charging Test Charging Test Main Menu Voltage of the charging system is low. The Data shows battery test, cranking and charging test results.
- Page 12 OPERATION (cont.) OPERATION (cont.) 6. From the Main Menu of the FBCBA-2000, use the up button (8) and down Print test results button (6) to select Print option and press enter button (7). 1. Before selecting print data from the main menu, it is necessary to connect the 7.
-
Page 13: Maintenance
MAINTENANCE DESCRIPTION OF SYMBOLS KNOW YOUR PRODUCT OPERATION (cont.) WARNING! Before cleaning the appliance make sure that it is Volts Amperes disconnected from the vehicle. Cold Cranking Amps Direct Current Cleaning Regulatory Compliance Mark Warning • We recommend that you clean the device immediately each time you have (RCM) finished using it. -
Page 14: Contents
NOTES CONTENTS 1 x 12V Battery & alternator tester 1 x USB cable 1 x Instruction manual Note: The manufacturer’s liability shall be deemed void if the tool is modified in any way and the manufacturer shall therefore accept no liability for any damages arising as a result of modifications. -
Page 15: Warranty
WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 951 371 New Zealand 0800 647 840...
Need help?
Do you have a question about the FBCBA-2000 and is the answer not in the manual?
Questions and answers