Trane Technologies BAYFLTR101C Installer's Manual

1” - 2” filter rack kit

Hide thumbs

Model:

BAYFLTR101C

BAYFLTR201C

WARNING:

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service information

pack upon completion of work.

NOTE: This filter rack is required when installing an economizer

or any outside air damper and recommends the use of the BAY-

ACCDOR Filter Access Door.

NOTE: To change filter rack from 1" to 2" filters:

• Remove 2 screws that secure the 1" filter angle to the Upper

Filter Channel and discard angle.

• Remove 2 screws that secure the 1" filter angle to the Lower

Filter Channel and discard angle.

Filter Rack Installation

1. Open or remove the Filter Access Door. See Figure 1.

2. UPPER FILTER CHANNEL:

a. Remove the screw from the top of the right coil blank-off

plate just inside the Coil Access opening, see Figure 1.

b. Hook the left side of the upper filter bracket into the tab

projecting from the rear/left end of the indoor coil flashing.

c. Install the right side of the upper filter bracket, aligning the

slots of the filter frame to the right coil tube sheet engagement

holes (where the screw was removed in Step a). See Figure 3.

3. LOWER FILTER CHANNEL:

Slide the lower filter channel across the drain pan and place the

channel bracket lip over the drain pan.

4. Install the appropriate filter(s) and fill plate. Close the Filter

Access Door or panel. See Table 1 for appropriate filter sizes.

NOTE: For unit horizontal applications, Return Air Panel is

to remain attached to the unit base pan return opening. Bottom

filter rack channel will sit on top of Return Air Panel perimeter

flange.

HAZARDOUS PRESSURES!

Coils contain refrigerant under pressure. When attaching filter channel

assemblies and filter retainer angle to coil blank-off plate use ONLY

the holes from which you removed the screws. Failure to follow these

safety precautions could result in coil bursting, which could result in

death or serious injury.

Installer's Guide

1" - 2" Filter Rack Kit

Used With:

2/4YC*,WC*,TC*,DC**018-036A

2/4YC*,WC*,TC*,DC**042-060A

HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING

WARNING

18-BH20D1-7A-EN

Figure 1. Filter Access Door

A FILL PLATE IS FURNISHED IN

THE BAYFLTR101C KIT.

Figure 2. Right Side Fill Plate

CAUTION

SHARP EDGE HAZARD!

Be careful of sharp edges on equipment or any cuts

made on sheetmetal while installing or servicing.

Personal injury may result.

RIGHT

BLANK-OFF

PLATE

SCREW

FILTER

LOCATION

Table of Contents

Need help?

Do you have a question about the BAYFLTR101C and is the answer not in the manual?

Questions and answers

Summary of Contents for Trane Technologies BAYFLTR101C

Page 1 4. Install the appropriate filter(s) and fill plate. Close the Filter Access Door or panel. See Table 1 for appropriate filter sizes. A FILL PLATE IS FURNISHED IN THE BAYFLTR101C KIT. NOTE: For unit horizontal applications, Return Air Panel is to remain attached to the unit base pan return opening. Bottom Figure 2. Right Side Fill Plate filter rack channel will sit on top of Return Air Panel perimeter flange.
Page 2 UPPER FILTER CHANNEL FILL PLATE (USED ON 018 – 036 MODELS ONLY) REAR SLOT INSERT OVER TAB ON UNIT BARRIER LOWER FILTER CHANNEL Figure 3. Filter Rack Components PRINTED FROM D675126P01 042 – 060 models shown INDOOR COIL AIRFLOW AIRFLOW INSTALLED FILTER RACK TWO-INCH...

This manual is also suitable for:

Bayfltr201c