Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for SINUS PLASMA 35/40
- Page 1 PLASMA LINE SINUS PLASMA 35/40 USER MANUAL MANU.115.X.PLA.xx 2009 beta...
-
Page 2: Table Of Contents
Valued Customer, Hoping you will find our product to your satisfaction, we welcome you to our family, informing you that the ERGUS marked machines have been ISO 9000:2001 certified, thus guaranteeing greater product reliability and quality. Tec.La is certified by RINA for quality system. TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS... -
Page 3: General Safety Information
GENERAL SAFETY INFORMATION GENERAL SAFETY INFORMATION GENERAL SAFETY INFORMATION GENERAL SAFETY INFORMATION Electric shock ELECTRIC SHOCK CAN KILL. • Do not touch the parts under high voltage; • Disconnect the power supply from mains before any intervention; • Operator must be insulated from the piece to be cut and from the ground, wearing insulated gloves and clothing;... - Page 4 Noise The cutting arc respects current legislation on noise levels (not exceeding 80db); Protective ear plugs or muffs must be worn to avoid damage when working overhead or in small areas. Heat, jets of melted metal and sparks During cutting, the heat, jets of melted metal and sparks can cause fires: •...
-
Page 5: The Plasma Cutting
SCRIPTION OF POWER SOURCE SCRIPTION OF POWER SOURCE Portable SINUS PLASMA 35/40 ADV single phase inverter generator is a systems for cutting carbon steel, stainless steel, aluminium and other metals with the compressed air plasma technique starting with a pilot arc. -
Page 6: Placing The Equipment
1. Placing the eq 1. Placing the eq 1. Placing the eq 1. Placing the equipment uipment uipment uipment Avoid placing the equipment in areas that limit the air flow from the fan and from the ventilation grids (do not cover the power source). -
Page 7: Front Panel Controls
3. Front panel controls 3. Front panel controls 3. Front panel controls 3. Front panel controls SUNUS PLASMA 35/40 ON-OFF LED OUTPUT CUTTING CURRENT REGULATION OVERHEATING LED EARTH CABLE CONNECTOR TORCH CONNECTOR ON-OF SWITCH (on the back panel) PRESSURE GAUGE... -
Page 8: Installation Of Plasma Cutting Machines
MACHINES MACHINES MACHINES MACHINES SINUS PLASMA 35/40 ADV All cutting parameter controls are placed on the cutting machine front panel. • Ref. 4 Connect the earth cable to the piece to cut, making sure that there is good electrical contact, in particular with sheet metal that is painted, oxidised or has insulation covering. - Page 9 • Press the torch trigger to ignite the pilot arc; when the push button is released air will continue to exit the torch for a few seconds in order to cool it; • If within a few seconds the pilot arc does not become a cutting arc, it turns off. To turn it on again, release the torch trigger and press it again;...
-
Page 10: Plasma Cut Defects
(mm) (mm) (mm) (mm) (mm) (lt/min.) (bar) SINUS PLASMA 35/40 3,5-4,0 TORCH MAINTENANCE TORCH MAINTENANCE TORCH MAINTENANCE TORCH MAINTENANCE Excessive wear of spare parts is caused by wet compressed air, incorrect start-ups from the workpiece middle, excessive cutting speed. •... -
Page 11: Torch Exploded View
TORCH EXPLODED VIEW TORCH EXPLODED VIEW TORCH EXPLODED VIEW TORCH EXPLODED VIEW SINUS PLASMA 35/40 ITEM CODE DESCRIPTION PT-40 Plasma Torch CO.52531 PT-40 electrode CO.60028 PT-40 swirl baffle CO.51316 PT-40 nozzle 0,8mm CO.60389 PT-40 heat shield... -
Page 12: Technical Data
TECHNICAL DATA TECHNICAL DATA TECHNICAL DATA TECHNICAL DATA SINUS PLASMA 35/40 DUTY PLASMA duty cycle 35 A – 40% PLASMA output at 100% duty cycle 22 A INVERTER Mains voltage 230V ±10% Frequency 50/60Hz 270 V PLASMA Nominal Power (100%)
Need help?
Do you have a question about the PLASMA 35/40 and is the answer not in the manual?
Questions and answers