1. Manuals
  2. Brands
  3. Trimteck Manuals
  4. Controller
  5. OPTIMUX OpTK
  6. Product instruction manual

Trimteck OPTIMUX OpTK Product Instruction Manual

Spring cylinder rotary actuators
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Product Instruction Manual
OpTK
Spring Cylinder Rotary Actuators

TABLE OF CONTENTS

INTRODUCTION

Safety Information ........................ pg. 1
Unpacking ...................................... pg. 1
INSTALLATION ........................................ pg. 1
PREVENTIVE MAINTENANCE ................ pg. 2
Actuator Removal ..........................pg. 2
ACTUATOR ACTION REVERSAL .......... pg. 5
INTRODUCTION
The following instructions are designed to assist in
unpacking, installing and performing maintenance
as required on Optimux Spring Cylinder Rotary
Actuators. Product users and maintenance
personnel should thoroughly review this bulletin
prior to installing, operating or performing any
maintenance on the actuator.

SAFETY INFORMATION

WARNING: Indicates a potentially
hazardous situation, which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation, which, if not
avoided, could result in minor or
moderate injury and/or property
damage.
Note:
Indicates a potential situation,
which, if not avoided, may result in an
undesired result or state.
Leading Technologies
For Control
This publication does not contain information on
Optimux positioners. Refer to the appropriate
maintenance bulletin for installing, calibrating,
maintaining,
troubleshooting
Optimux positioners.

Unpacking

1. While unpacking the actuator, check the
packing list against the materials received.
2. When lifting the actuator from the shipping
container, position lifting straps and hoist to
avoid damage to tubing and mounted
accessories.
WARNING:
with lifting straps, be aware the
center of gravity may be above the
lifting point. Therefore, support
must be given to prevent the
actuator from rotating. Relieve
spring compression by removing
adjusting screw.
3. Contact your shipper immediately in the case
of any shipping damage.
4. Contact your Optimux representative with any
problems.

INSTALLATION

Prior to installation, make sure adequate
overhead and side clearance for the actuator is
provided to allow for proper removal and for
proper maintenance. Refer to Table I.
Actuator Size
25
50
100, 200
Table I: Overhead Clearance for Disassembly
and
operating
When lifting an actuator
Minimum Clearance
6 inches
8 inches
9 inches

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OPTIMUX OpTK and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Trimteck OPTIMUX OpTK

  • Page 1 Leading Technologies For Control Product Instruction Manual OpTK Spring Cylinder Rotary Actuators This publication does not contain information on TABLE OF CONTENTS Optimux positioners. Refer to the appropriate INTRODUCTION maintenance bulletin for installing, calibrating, maintaining, troubleshooting operating Safety Information ......pg. 1 Optimux positioners.
  • Page 2 OpTK Spring Cylinder Rotary Actuators Note: Although Optimux rotary spring 2. Clean actuator and repaint oxidized areas. cylinder actuators can be mounted in any 3. If possible, stroke actuator and check for position, mounting the cylinder vertically is smooth, full-stroke operation. the preferred installation.
  • Page 3 Product Instruction Manual DISASSEMBLING THE ACTUATOR WARNING: Do not scratch the Disassembling Actuators with clamping and Non- bottom surface of the sliding seal clamping Lever Arm If it is necessary to collar with a screwdriver or disassemble an actuator with a non-clamping sharp object.
  • Page 4 OpTK Spring Cylinder Rotary Actuators 7. Install cover plate and yoke onto transfer WARNING: Ensure that case. The four tapered lug bolts are used cylinder retaining ring is completely with the yoke and standard hex bolts are seated in the cylinder groove. used with the cover plate.
  • Page 5 Product Instruction Manual 1. Cycle the valve (or mechanical device) to just 7. Reverse the transfer case on the yoke by beyond the closed position with very low turning it 180 degrees. The yoke side now supply air pressure (10-15 PSI). becomes the cover plate side and the cover plate side becomes the yoke side.
  • Page 6 OpTK Spring Cylinder Rotary Actuators Adjusting Screw Gasket Adjusting Screw (Item No. 248) (Item No. 210) Cylinder Spring Button (Item No. 202) (Item No. 227) Spring (Item No. 229) Actuator Stem Locknut (Item No. 348) Piston Stem O-ring (Item No. 272) Actuator Stem O-Ring (Item No.
  • Page 7 Product Instruction Manual Item No. Description Yoke Cylinder Transfer Case Adjusting Screw Actuator Stem Stroke Plate Piston Spring Button Spring Follower Pin Yoke Bushing Adjusting Screw Gasket Lever Arm Cylinder Retaining Ring Cover Plate Bushing Piston Backup Ring Piston O-ring Piston Stem O-ring Cylinder O-ring Actuator Stem O-ring...
  • Page 8 Optimux is continually improving and upgrading its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user should contact TRIMTECK, LLC at any of its worldwide operations or offices. For more information about Trimteck and its products, For more information, contact: contact www.trimteck.com or call USA (954) 753-5545...

Table of Contents