Summary of Contents for Munters PI0848
- Page 1 Plastic Inlet Instruction Manual Plastic Inlet Models: PI0848 • PI1248 • PI1548 © Munters Corporation, May 2017 QM1044r5...
-
Page 2: Warranty
With the proper installation and maintenance it will provide many years of service. Please Note: To achieve maximum performance and insure long life from your Munters product it is essential that it be installed and maintained properly. Please read all instructions carefully before beginning installation. Warranty: For Warranty claims information see the “Warranty Claims and Return Policy”... - Page 3 Index Chapters Page 1. Unpacking the Equipment Parts List Inlet Dimensions 2. Installation Instructions 3. Cabling © Munters Corporation, May 2017 QM1044r5...
-
Page 4: Unpacking The Equipment
AC1039 ⁄ ” Dia. Cable Clamp, ZP 1.2 Inlet Dimensions WALL OPENING (I.D., framed) " ⁄ " H. x 47" W. ⁄ ” H. x 47” W ⁄ ” H. x 47” W © Munters Corporation , May 2017 QM1044r5... -
Page 5: Installation Instructions
Construct framed opening to correct size according to the Wall Opening listed in chart on previous page. A minimum of 10” - 12” from ceiling to the top inside of the stud. See Figure 1A and 1B. Frame Construction Figure 1A Post Construction Figure 1B © Munters Corporation, May 2017 QM1044r5... - Page 6 (2) Bolts [B], Nuts [C] and Washers [D] (provided). Top bolt should go through top extrusion. See Figure 2. Front View Figure 2 © Munters Corporation , May 2017 QM1044r5...
- Page 7 Install Screw Hooks [L] centered on length of PB inlet and 2½” above top framed opening. See Figure 3A and 3B. For post frame construction, also, install a screw hook on each post near the ceiling. See Figure 3C. Figure 3A Figure 3B Figure 3C © Munters Corporation, May 2017 QM1044r5...
- Page 8 Install inlet onto opening by folding hinge upward and aligning rigid part of hinge with bottom of opening as shown in Figure 4A. Lag screws (not provided) should be installed at 3.5”O.C. See Figure 4B and 4C. Figure 4A Figure 4B Figure 4C © Munters Corporation , May 2017 QM1044r5...
- Page 9 Cabling Step 5 Attach pulleys in line with screw hooks at each endwall. See Figure 5A and 5B. Figure 5A Figure 5B © Munters Corporation, May 2017 QM1044r5...
- Page 10 Pull main cable from winch or actuator through pulleys and screw hooks to weights or return spring on opposite end wall. See Figures 5A, 5B, 6A and 6B. Be sure to coil approximately 1’ of cable on winch. Figure 6A Figure 6B © Munters Corporation , May 2017 QM1044r5...
- Page 11 Run each lift line through the adjacent Nylon Guide Link [M] and attach Azuma Bolt and Nut [K]. See Figure 7A , 7B and 7C. Figure 7A Figure 7C Figure 7B © Munters Corporation, May 2017 QM1044r5...
- Page 12 Install optional Latch Bracket. The latch bracket should be located near the top center of the inlet. The spacer should not interfere with the inlet seal. See Figure 9A and 9B. Figure 9A © Munters Corporation , May 2017 QM1044r5...
- Page 13 Chapter 3 Cabling Figure 9B © Munters Corporation, May 2017 QM1044r5...
- Page 14 Plastic Inlets are developed and produced by Munters Corporation, Lansing, Michigan U.S.A. 1-800-227-2376 Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66. Munters Corporation 2691 Ena Drive Lansing, MI 48917 U.S.A. Phone +1 800-227-2376, Fax +1 517-676-7078 www.munters.us...