Summary of Contents for WinSystems PCM-DC-AT512-P
- Page 1 sales@artisantg.com artisantg.com (217) 352-9330 | Visit our website - Click HERE...
- Page 2 WinSystems ® PCM-DC-AT512-P +5V and ±12V DC/DC PC/104 Power Supply PRODUCT MANUAL WinSystems, Inc. 715 Stadium Drive Arlington, TX 76011 http://www.winsystems.com...
- Page 3 MANUAL REVISION HISTORY P/N G400-0379-000B (PCM-DC-AT512-P) Revision Date Code ECO Number 120410 Initial Release 120510 120614 130718 130725 130806 130809 130809 PRODUCT MANUAL PCM-DC-AT512-P...
-
Page 4: Table Of Contents
J7, J8 - Auxiliary Power PC/104 BUS J1, J5 - PC/104 CABLES SPECIFICATIONS MECHANICAL DRAWING APPENDIX - A BEST PRACTICES APPENDIX - B EFFICIENCY MEASUREMENTS APPENDIX - C START-UP TIMING APPENDIX - D OUTPUT DERATING WARRANTY INFORMATION 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 5: Before You Begin
Please review these guidelines carefully and follow them to ensure you are successfully using your embedded PC. For any questions you may have on WinSystems products, contact our Technical Support Group at (817) 274-7553, Monday through Friday, between 8 AM and 5 PM Central Standard Time (CST). -
Page 6: Visual Index - Top View (Connectors & Leds)
Auxiliary Power Power Input -12V (GREEN) +12V (YELLOW) +5V (RED) PC/104 (C/D) PC/104 (A/B) NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable. 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 7: Status Led
Index The PCM-DC-AT512-P has up to 3 status LED indicators populated on the board at D5, D7, and D8, which can display the status of each regulated output. When one of the LEDs is not lit or pulses ON and OFF, the respective supply is not in regulation. - Page 8 This page has been left intentionally blank. 130809 PRODUCT MANUAL PCM-DC-AT512-P...
-
Page 9: Introduction
INTRODUCTION This manual is intended to provide the necessary information regarding configuration and usage of the PCM-DC-AT512-P power supply. WinSystems maintains a Technical Support Group to help answer questions not adequately addressed in this manual. Contact Technical Support at (817) 274-7553, Monday through Friday, between 8 AM and 5 PM Central Standard Time (CST). -
Page 10: System
System The PCM-DC-AT512-P is a high efficiency, non-isolated switch mode power supply with a wide input range of 10-50 VDC. From one common DC input, it supplies +5V, -12V, and 12V. The overall efficiency of the power supply varies between 80 and 92% depending on the individual converter loading and input level. -
Page 11: Connector Reference
Mating Connector: PHOENIX 1803578 (Housing) *Note: Mating Connector ships with board. □ +10-50 VDC □ DC power input is supplied to the PCM-DC-AT512-P via the 2-pin Phoenix connector at J2. Visual J7, J8 - Auxiliary Power Index PCB Connector: PHOENIX CONTACT 1725672 J7, J8 □... -
Page 12: Pc/104 Bus
The PC/104 bus is electrically equivalent to the 16-bit ISA bus. Standard PC/104 I/O cards can be populated on PCM-DC-AT512-P’s connectors, located at J1 and J5. The interface does not support hot swap capability. The PC/104 bus connector pin definitions are provided below for reference. Refer to the... -
Page 13: Cables
CABLES See WinSystems website. 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 14: Specifications
MIL-217 Part Count Reliability method using Manufacturer’s Failure Rate Data Mechanical Dimensions 3.6 x 3.8 inches (90 x 96 mm) Weight 4 oz (114g) Printed Circuit Board 0.078 inches 4-Layer FR4 Environmental Operating Temperature -40°C to 85°C ambient Humidity 5% to 95% non-condensing 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 15: Mechanical Drawing
MECHANICAL DRAWING .480 12.20 .079 2.01 3.575 90.81 3.375 85.73 2.888 73.35 2.317 58.84 .551 14 .200 5.08 .400 10.15 .125 3.18 (4X) .480 12.20 .079 2.01 .435 11.05 .400 10.15 PCM-DC-AT512-P 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 16: Best Practices
Use the largest gauge wire that you can. Most connector manufacturers have a maximum gauge wire they recommend for their pins. Try going one size larger; it usually works and the extra copper will help your system perform properly over time. 130809 PRODUCT MANUAL PCM-DC-AT512-P... - Page 17 Contact Points WinSystems’ boards mostly use connectors with gold finish contacts. Gold finish contacts are used exclusively on high speed connections. Power and lower speed peripheral connectors may use a tin finish as an alternative contact surface. It is critical that the contact material in the mating connectors is matched properly (gold to gold and tin to tin).
- Page 18 CONFORMAL COATING Applying conformal coating to a WinSystems product will not in itself void the product warranty, if it is properly removed prior to return. Coating may change thermal characteristics and impedes our ability to test, diagnose, and repair products.
- Page 19 Every single board computer has an Operations manual or Product manual. Manual Updates Operations/Product manuals are updated often. Periodicially check the WinSystems website (http://www.winsystems.com) for revisions. Check Pinouts Always check the pinout and connector locations in the manual before plugging in a cable. Many single board computers will have identical headers for different functions and plugging a cable into the wrong header can have disastrous results.
-
Page 20: Efficiency Measurements
APPENDIX - B EFFICIENCY MEASUREMENTS CONVERTER EFFICIENCY CONVERTER EFFICIENCY 100% +3.3V +12V +5VSB -12V 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 21: Start-Up Timing
APPENDIX - C START-UP TIMING ITO (No Load) *Note: +5V STBY and +3.3V apply to the PPM-DC-ATX model only. 130809 PRODUCT MANUAL PCM-DC-AT512-P... - Page 22 ITO (No Load) 130809 PRODUCT MANUAL PCM-DC-AT512-P...
-
Page 23: Output Derating
APPENDIX - D OUTPUT DERATING 130809 PRODUCT MANUAL PCM-DC-AT512-P... -
Page 24: Warranty Information
WARRANTY INFORMATION (http://www.winsystems.com/warranty.cfm) WinSystems warrants to Customer that for a period of two (2) years from the date of shipment any Products and Software purchased or licensed hereunder which have been developed or manufactured by WinSystems shall be free of any material defects and shall perform substantially in accordance with WinSystems’...
Need help?
Do you have a question about the PCM-DC-AT512-P and is the answer not in the manual?
Questions and answers