TVT Digital TD-3104H1-4P-B1 Quick Start Manual

Network Video Recorder
Quick Start Guide
● Please read this instruction carefully before using the product and keep
it for further reference.
● All the examples and pictures used here are for reference only.
● The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
1. Packing Check
Please check the device and the accessories after getting the device. If there
are any damages, shortages or defects, please contact your dealer immediately.
2. HDD Installation
This series of the product supports 1 SATA hard drive. Please make sure that the
device is powered off before the installation. The pictures of the installation are only
for reference, please take the real object as the standard.
① Loosen the screws to open the cover.
② Screw the screws into the HDD but not tighten them.
③ Place the HDD onto the bottom of the machine.
④ Turn over the machine and secure the HDD with the screws.
⑤ Connect the power and data cables.
⑥ Install back the cover and secure it with the screws.
Tips: Please check the inside structure of the device and make sure the cables connected
well before installing the cover back. Please format the HDD before using.
3. Rear Panel Instruction
The interfaces of the rear panel are for reference only.
Name Description
Connector for power input
DC48V
PoE network ports; connect to PoE IP cameras
PoE Ports
LAN Network port
VGA Connect to monitor
Connect to high definition display device
HDMI
Connect to USB storage device or USB mouse
USB
Audio output
AUDIO OUT
AUDIO IN Audio input
4. Startup & Shutdown
►Startup
① Connect the monitor and the power.
② The device will boot and the power indicator will display blue.
③ A wizard window will pop up.
►Shutdown
Click "Start" and then select "Shutdown" icon. This will bring up a shutdown
window. The device will shut down by clicking "OK" button. Then disconnect
the power.
5. System Login
You must configure the wizard if you start the NVR for the first time. After you
read the privacy statement, click "Wizard Setup" to start Wizard. Then set the
data, time and zone as needed. After that, set the login password.
Wizard
Admin Password Setup
Username admin
New Password xxxxxx
xxxxxx
Confirm Password
Display Password Log In Automatically
Pattern Lock
Enable Edit
Previous
The default username is admin. Set your own password when you use the
wizard for the first time. Enable pattern lock and click "Edit" to set the pattern
lock. Then set security questions and answers. It is important for you to
remember these answers, or you will not be able to reset your password. Click
"Next" to continue.
6. Network Configuration & Add IP Camera
① In the above wizard interface, click "Next" to set the network.
Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP
in both the NVR and the router.
② Enter HTTP port (the default value is 80) and server port (the default port is
6036).
③ The internal ethernet port is the port which connects all the PoE ports with
the NVR system. The PoE ports are available if the internal ethernet port is
online; if it is offline, all the PoE ports will be unavailable. The IP address and
subnet mask of the internal ethernet port can be changed to make the port in the
same network segment with the IP cameras which directly connect to the PoE
ports of the NVR.
Network Settings
Ethernet Port 1 ( Online )
Obtain an IP address automatically
Address
Subnet Mask
Gateway
Obtain DNS automatically
Preferred DNS
Alternate DNS
HTTP Port
HTTPS Port
④ Add Camera. Click "Next" to go to the following interface. Click "Refresh" to
refresh the list of online IP cameras which are in the same local network with the
NVR. Click + to add the searched camera. Click "Add All" to add all the
cameras in the list. Click
to delete all the added cameras.
Network Settings
No.
Next
Wizard
Internal Ethernet Port ( Online )
Address
192 . 168 . 1 . 2 192 . 168 . 1 . 3
255 255 . . 255 . 0 255 255 . . 255 . 0
Subnet Mask
192 . 168 . 1 . 1
. . .
. . .
80 RTSP Port 554
Sever Port
443 6036
Previous Next
to delete the added camera. Click "Delete All"
Wizard
Add Camera
Address
Edit Port Protocol Model Version
80
1 192.168.1.20 XXX XXX 3.4.2
80
2 192.168.1.38 XXX XXX 3.4.2
80
3 192.168.2.45 XXX XXX 4.0.0.1.beta1
Remain Bandwidth: 20 / 40 Mb
Refresh Add All Delete All
No.
IP Camera Name Address Protocol Status Edit Delete
1 [POE1] IPC 192.168.1.20 XXX Online
Cancel
Add
_ _ _
+
+
+