Table of Contents
Advertisement
Remote Control Functions
Macro Buttons: Press these buttons
to store or recall a "Macro", which is a
pre-programmed sequence of commands
stored in the remote. (See page 30 for more
information on storing and recalling macros.)
Transport Buttons: These buttons do not
have any functions for the AVR, but they may be
programmed for the forward/reverse play opera-
tion of a wide variety of CD or DVD players, and
audio or video- cassette recorders. (See page 29
for more information on programming the
remote.)
Skip Up/Down Buttons: These buttons
do not have a direct function with the AVR, but
when used with a compatibly programmed CD
or DVD changer they will change the tracks on
the disc currently being played in the changer.
RDS Select Button: Press this button to
display the various messages that are part of the
RDS data system of the AVR 's tuner. (See page
28 for more information on RDS).
Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the AVR 's memory.
When CD or DVD is selected using the Input
Selector button
, these buttons may func-
tion as Slow Fwd/Rev (DVD) or "+10" (CD).
Clear Button: Press this button to clear
incorrect entries when using the remote to
directly enter a radio station's frequency.
Memory Button: Press this button to enter
a radio station into the AVR 's preset memory. Two
underline indicators will flash at the right side of
the Main Information Display
have five seconds to enter a preset memory
location using the Numeric Keys
page 27 for more information.)
Delay/Prev Ch.: Press this button to begin
the process for setting the delay times used by
the AVR when processing surround sound. After
pressing this button, the delay times are entered
by pressing the Set button
and then using
the
buttons
to change the setting.
K
/
L
Press the Set button again to complete the
process. (See page 19 for more information.)
Button: This button does not have a
B
function with the AVR. When a DVD player or TV
is selected, it may be used to navigate the menus
of those devices.
Speaker Select: Press this button to
begin the process of configuring the AVR's Bass
Management System for use with the type of
speakers used in your system. Once the button
has been pressed, use the
buttons
K
/
L
select the channel you wish to set up. Press the
Set button
and then select the speaker
type (see page 16 for more information.)
Tone Mode: Pressing this button enables
or disables the Balance, Bass and Treble tone
controls. When the button is pressed so that the
words
TONE I N
Information Display
Bass and Treble controls and of the Balance
control will affect the output signals. When the
button is pressed so that the words
appear in the Main Information
OUT
Display
, the output signal will be "flat, "
without any balance, bass or treble alteration.
Volume Up/Down: Press these buttons to
raise or lower the system volume.
TV/Video Button: This button does not
have a direct function on the AVR, but when
used with a compatibly programmed VCR, DVD
or satellite receiver that has a "TV/Video" func-
tion, pressing this button will switch between
the output of the player or receiver and the
external video input to that player. Consult the
Owner's Manual for your specific player or
receiver for the details of how it implements this
function.
Mute: Press this button to momentarily
silence the AVR or TV set being controlled,
depending on which device has been selected.
When the AVR remote is being programmed to
operate another device, this button is pressed
with the Input Selector button
the programming process. (See page 29 for more
information on programming the remote.)
NOTE: As any of the remote buttons pressed is
active with the device selected, the correspon-
ding Selector button
, you then
red to confirm your selection.
. (See
Dim Button: Press this button to activate
the Dimmer function, which reduces the bright-
ness of the front panel display, or turn it off
entirely. The first press of the button shows the
default state, which is full brightness by indicat-
ing
VFD FULL
Display
. Press the button again within five
seconds to reduce the brightness by 50%, as
indicated by
VFD HALF
again within five seconds and the main display
will go completely dark. Note that this setting is
temporary; the display will always return to full
brightness when the AVR is turned on. In addi-
tion,both the Power Indicator
accent lighting inside the volume control will
always remain at full brightness regardless of
the setting. This is to remind you that the AVR is
still turned on.
Dolby Mode Selector: This button is used
to
to select one of the available Dolby Surround
processing modes. Each press of this button will
select one of the Dolby Pro Logic II modes, Dolby
3 Stereo or Dolby Digital. Note that the Dolby
Digital mode is only available with a digital input
appear in the Main
, the settings of the
TONE
to begin
will briefly flash
in the Main Information
. Press the button
and the blue
selected and the other modes only as long as a
Dolby Digital source is not playing. See page 22
for the available Dolby surround mode options.
DTS Digital Mode Selector: When a DTS
source is in use the AVR will select the appropri-
ate mode automatically and no other mode will
be available. Pressing this button will display the
mode currently selected by the AVR´s decoder,
depending on the surround material played and
the speaker setting.
Logic 7 Selector: Press this button to
select one of the available Logic 7 surround
modes. (See page 22 for the available Logic 7
options).
Stereo Mode Selector: Press this button to
select a stereo playback mode. When the button
is pressed so that
DSP SURR OFF
in the Main Information Display
will operate in a bypass mode with true fully
analog, two-channel left/right stereo mode with
no surround processing or bass management as
opposed to other modes where digital process-
ing is used. When the button is pressed so that
appears in the Main
SURROUND OFF
Information Display
, you may enjoy a
two-channel presentation of the sound along
with the benefits of bass management. When
the button is pressed so that
5 C H STEREO
appears, the stereo signal is routed to all five
speakers, if installed.(See page 18 for more
information on stereo playback modes).
DTS Neo:6 Mode Selector: Pressing this
selector button cycles the AVR through the
various DTS Neo:6 modes, which extract a five-
channel surround field from two-channel pro-
gram material (from PCM source or analog input
signal). The first press selects the last DTS Neo:6
surround mode that was in use, and each
subsequent press selects the next mode in the
following order:
DTS Neo:6 MUSIC
DTS Neo:6
CINEMA
6-Channel Direct Input: Press this button
to select the component connected to the
6-Channel Direct Input
as the audio.
Note that when you wish to use the Six Channel
Direct Input in conjunction with a video source,
you must first select the video source by pressing
one of the Input Selectors
. Then press this
button to choose the 6-Channel Direct Input
as the audio source.
REMOTE CONTROL FUNCTIONS 11
appears
, the AVR
Hide quick links:
Advertisement
Table of Contents
