Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SENTRY II 970 Series
- Page 1 Service Manual...
-
Page 3: Table Of Contents
Table of Contents TABLE!OF!CONTENTS Page General Warnings ........................3 Installation ..........................5 Programming ......................... 7 System Start-Up ........................8 Frequently Asked Questions ....................10 Drawings and Part Numbers ....................11 Front Cover and Drive Assembly Breakdown ..............12 Internal Parts Breakdown ....................13 Injector Assembly Breakdown .................... -
Page 4: General Warnings
Introduction General Warnings 1. The control valve, fittings and/or bypass are ware version (e.g. 154) and then reset the valve to designed to accommodate minor plumbing mis- the service position. alignments but are not designed to support the weight of a system or the plumbing. 6. -
Page 5: Installation
Installation Pre-Installation Checklist 5. Plumbing preparation: Un-screw the two plas- tic nuts (#1) and pull on the two brass connectors 1. A standard electrical outlet (120V/60Hz) must be (#4) to remove them from the bypass assembly. located within 12’ of the installation site. Next remove the white plastic split rings (#2) and the O-Rings (#3). - Page 6 Installation 10. Temporary Drain Tube: Now that the water 14. Connecting the overflow line: The brine softener is connected to the existing plumbing, overflow fitting is located on the outside of the the drain line may be connected. First, discon- salt container approximately 12”...
-
Page 7: Programming
Programming Programming the Controller 2. Setting the Water Hardness, Day Override and regeneration times: 1. Setting the Clock: When the controller is first plugged in, the time of day display will be flash- Step 1: Press and hold the NEXT button and ing. -
Page 8: System Start-Up
Programming System Start-Up Step 4 Setting the time of regeneration: Start -Up Instructions The hour display will now be flashing. Set the 1. Adding Water to Salt Container: Manually fill correct hour by pressing either the or the the salt container with fresh water until there is arrow button. - Page 9 System Start-Up Step 3: Press the REGEN button. The drive Step 7: If the controller has not already moved to the “FILL” cycle, press the REGEN button. The motor will run and the “BRINE” display will flash until the drive motor stops. drive motor will run and the FILL display will flash until the drive motor stops.
-
Page 10: Frequently Asked Questions
Frequently Asked Questions Frequently Asked Questions 5. Question: How often does the salt tank need to be cleaned? 1. Question: What type of salt can I use in this softener? Answer: Dirt, rocks and debris collect in the bottom of the Answer: salt container (a little in each bag of salt). -
Page 11: Drawings And Part Numbers
Drawings and Part Numbers DRAWINGS AND PART NUMBERS Page 11... -
Page 12: Front Cover And Drive Assembly Breakdown
Front Cover and Drive Assembly Breakdown Page 12... -
Page 13: Internal Parts Breakdown
Internal Parts Breakdown Page 13... -
Page 14: Injector Assembly Breakdown
Injector Assembly Breakdown Page 14... -
Page 15: Brine Elbow Assembly Breakdown
Brine Elbow Assembly Breakdown Page 15... -
Page 16: 3/4" Drain Fitting Breakdown
3/4” Drain Fitting Breakdown Page 16... -
Page 17: 1" Drain Fitting Breakdown
1” Drain Fitting Breakdown Page 17... -
Page 18: Meter Assembly Breakdown
Meter Assembly Breakdown Page 18... -
Page 19: Installation Fitting Assemblies
Installation Fitting Assemblies Page 19... -
Page 20: Bypass Assembly Breakdown
Bypass Assembly Breakdown Page 20... -
Page 21: Bypass Valve Operation
Bypass Valve Operation Page 21... -
Page 22: Trouble Shooting Procedures
Trouble Shooting Procedures Page 22... - Page 23 Trouble Shooting Procedures Page 23...
- Page 24 L-970 Printed in the U.S.A. Rev. 160112.1...
Need help?
Do you have a question about the 970 Series and is the answer not in the manual?
Questions and answers
how do you make the water softer or harder
To adjust the water hardness on a SENTRY II 970 Series:
1. Press and hold the NEXT button and the button with the clock symbol at the same time for about 2 seconds.
2. The “SET HARDNESS” display will flash.
3. Use the arrow buttons to set the correct raw water hardness level.
This answer is automatically generated
how to find a local dealer in Boise ID for the Sentry II 970