Advertisement
Quick Links
Advertisement
Related Manuals for Gallo Acoustics ROOMSUB
Summary of Contents for Gallo Acoustics ROOMSUB
- Page 1 R O O M S U B O W N E R ’ S G U I D E...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INSTRUCTIONS PRODUCT DISPOSAL INTRODUCTION AND RUN-IN PLACEMENT OF SUBWOOFER CONTROLS AND CONNECTIONS 2.1 SET-UP MULTI-CHANNEL SET UP SPECIFICATION - ROOMSUB 8 SPECIFICATION - ROOMSUB 10 WARNING AND WARRANTY TECHNICAL SUPPORT... -
Page 4: Important Safety Instructions
Do not overload wall sockets or extension cords. If there is any damage or failure, unplug the subwoofer from the wall socket immediately and consult qualified sources for advice. In the event of a failure, contact your dealer, distributor or Gallo Acoustics directly to arrange repair. - Page 5 INTRODUCTION RUN-IN PERIOD Thank you for choosing Gallo Acoustics. Your Gallo Acoustics RoomSub utilises technologies that only reach their optimum performance levels Please take the time to read and understand this after a period of 20 - 40 hours of use. During this guide thoroughly before installing your RoomSub.
- Page 6 PLACEMENT The placement of your RoomSub subwoofer within the room is not as critical as speaker placement, since RoomSub frequencies of 80Hz and below are non-directional. This allows you to place the subwoofer wherever you want in the room. • Ensure that the PHASE control is used properly.
-
Page 7: Controls And Connections
CONTROLS AND CONNECTIONS FRONT CONTROL PANEL REAR CONNECTOR PANEL... - Page 8 CROSSOVER LINE IN/OUT The CROSSOVER control is variable from 50Hz to This is used to connect your RoomSub to your 180Hz. In simple terms, the subwoofer will play all amplifier using a coaxial (RCA) cable. Connect the frequencies below the CROSSOVER setting.
- Page 9 2.1 SET-UP When using your RoomSub in a 2.1 set-up, connect as SPEAKER SPEAKER follows : • Run speaker cables from your amplifier to your loudspeakers. • If your amplifier has a dedicated subwoofer output, then this can be used to connect your amplifier to AMPLIFIER the subwoofer using a single coaxial (RCA) cable.
-
Page 10: Multi-Channel Set Up
• Make adjustments on your AV amplifier to ensure that the correct frequency range is being distributed to your speakers and subwoofer. For Gallo Acoustics Micro and A’Diva loudspeakers, use a small speaker setting on your amplifier, to protect the loudspeakers from the lowest frequencies. - Page 11 SPECIFICATION ROOMSUB 8 Frequency Response 32Hz to 150 kHz +/- 3db Class D Digital Power Amp 200W Active low pass filter 50Hz to 180Hz, continually variable Woofer 8” woofer with PP cone and NBR surround Weight 12Kg Enclosure Material MDF (Medium Density Fibreboard)
- Page 12 SPECIFICATION ROOMSUB 10 Frequency Response 32Hz to 160 kHz +/- 3db Class D Digital Power Amp 300W Active low pass filter 50Hz to 180Hz, continually variable Woofer 10” woofer with PP cone and NBR surround Weight 19Kg Enclosure Material MDF (Medium Density Fibreboard)
- Page 13 WARNING WARRANTY Care must be taken positioning the subwoofer to ensure Anthony Gallo Acoustics Ltd warrants to the end that it won’t be damaged or knocked over. user that this product will be free from defects in materials and workmanship in the course of normal...
-
Page 14: Technical Support
TECHNICAL SUPPORT Should you encounter problems using this product, please contact your dealer or local distributor. You can call Gallo Acoustics directly for technical support on the following numbers: 01555 666 883 Outside UK +44 1555 666 883 United States, Canada and South America... - Page 16 ANTHONY GALLO ACOUSTICS LTD THE INOX BUILDING CALDWELLSIDE LANARK SCOTLAND UNITED KINGDOM ML11 7SR WWW.GALLOACOUSTICS.COM...
Need help?
Do you have a question about the ROOMSUB and is the answer not in the manual?
Questions and answers