5 Installation and removal .......................... 14 5.1 Mount IC1000 and DIN-TS35 top-hat rail.................... 14 5.2 Establish connections .......................... 14 5.3 Remove the IC1000 from the DIN-TS35 top hat rail ................ 16 6 Decommissioning ............................ 17 6.1 Disposing of the device .......................... 17 6.2 Returning the device for maintenance, repair or disposal..............
This instruction manual is intended for operators and technically qualified personnel with experience in leak detection technology and the integration of leak detectors in leak detection systems. In addition, the installation and use of the device require knowledge of electronic interfaces. 4 / 24 IC1000-Operating-Instructions-jiqn22en1-01-(2205)
• Connecting a non-compatible device to the LD interface • Assignment of the actually unused RS485 terminals • Use in radioactive areas • Operation under unsuitable ambient conditions • Use outside the technical specifications. • Use of wrong cables and wires IC1000-Operating-Instructions-jiqn22en1-01-(2205) 5 / 24...
INFICON 2 Safety 2.1 Intended use The IC1000 is an interface adapter between a leak detector and a BM1000. ► Operate the device only according to this instruction manual. 2.2 Duties of the operator • Read, observe, and follow the information in this manual and in the work instructions provided by the owner.
Page 7
• Only instructed personnel should be permitted to work with and on the device. The instructed personnel must have received training on the device. • Make sure that authorized personnel have read and understood the instruction manual and all other applicable documents, see “Other associated documents [} 4]“. IC1000-Operating-Instructions-jiqn22en1-01-(2205) 7 / 24...
INFICON 3 Scope of delivery, transport, storage Scope of delivery Item Quantity IC1000 Data cable Set of cables Operating manual ► Check the scope of delivery after receipt of the product to make sure it is complete and to check for external damage.
Power supply 24 V DC Serial cable Data cable Fieldbus cable The IC1000 is an interface between a leak detector and a BM1000. It allows the BM1000 to be used on a leak detector without LD interface (M12 connector). IC1000-Operating-Instructions-jiqn22en1-01-(2205)
A prerequisite is that the leak detector has an RS232 interface that can handle the LD protocol with 19200 or 38400 baud. For this purpose, the IC1000 has an RS-232 port for connection to the leak detector and an LD interface for connection to the BM1000. this only applies to the ECOTEC E3000 from software version V3.33.
Page 11
Also two DIP switch blocks (S1 and S2). The baud rate for the LD protocol on the RS232 interface can be selected via DIP switch S2 / 1 on the IC1000. The IC1000 supports 19200 or 38400 baud (8 data bits, no parity, 1 stop bit, no hardware flow control).
Page 12
4 | Description INFICON 24V IN 24 V input Pin assignment: Name + 24V The voltage supply is normally provided by the leak detector. Use the appropriate cable from the supplied cable set for this purpose. 12 / 24 IC1000-Operating-Instructions-jiqn22en1-01-(2205)
The housing of the device is composed of synthetic material. Switch off the device and disconnect from the mains. When cleaning the housing, use an agent accepted for synthetic surfaces (for example a light household cleaner). Do not use any solvents that attack synthetic materials. IC1000-Operating-Instructions-jiqn22en1-01-(2205) 13 / 24...
Connect the RS232 and 24V IN ports to the leak detector using the cables supplied in cable set 200010785. If for some reason you want to operate the IC1000 with a separate 24 V supply voltage, observe the following note: NOTICE The device must be supplied with a circuit that meets the requirements of "Energy-...
Page 15
INFICON Installation and removal | 5 Connect IC1000 with BM1000 Use the data cable to connect the LD connector on the IC1000 to the LD connector on the BM1000. Length (in meters) Catalog number 560-334 560-332 560-335 560-340 Table 1: Data cable NOTICE The data cables cannot be connected in series.
5 | Installation and removal INFICON 5.3 Remove the IC1000 from the DIN-TS35 top hat rail Fig. 3: Remove IC1000 1. Use the flat-tip screwdriver to pull out the locking device. 2. Pull the device off of the top hat rail.
ð You will then receive a return number and the shipping address. Use the original packaging when returning. Before shipping the instrument, attach a copy of the completed contamination declaration to the outside of the package. IC1000-Operating-Instructions-jiqn22en1-01-(2205) 17 / 24...
Length (in meters) Catalog number 560-334 560-332 560-335 560-340 Table 2: Data cable NOTICE The data cables cannot be connected in series. The voltage supply is normally provided by the leak detector. The length must not exceed 30 meters. IC1000-Operating-Instructions-jiqn22en1-01-(2205) 19 / 24...