Advertisement
Table of Contents
Order# XXXXX - MOD-1363 - iPad Kiosk
Item
Qty.
Description
1
1
32.07" TSP49 Curved SEG Extrusion
2
1
32.07" TSP49 Curved SEG Extrusion
3
1
32.07" TSP49 Curved SEG Extrusion
4
1
32.07" TSP49 Curved SEG Extrusion
5
1
20"w TSP49 Horizontal SEG Extrusion
6
1
20"w TSP49 Horizontal SEG Extrusion
7
1
16.4170"w Z45 Horizontal Extrusion w/ 6"w S10
Steps:
1) Connect [1] to [2] and [3] to [4].
2) Connect [1/2] and [3/4] with [5].
3) Slide [7] into groove.
4) Connect [1/2] and [3/4] with [6] and assembled lightbox.
5) Attach assembled frame to base with bolts.
6) Attach front SEG graphics.
7) Position part [7] and lock in place.
8) Attach iPad mount see detail.
-- Continued page 2 --
Graphic: To Ensure Proper Fit
Corner A
Corner B
Corner D
Corner C
It is important to first insert
Step 1
Step 2
graphic into each alternate
Insert corner A. Turn edge of
Repeat Step 1 for opposite
corner then to the sides of
graphic so silicon welt is
corner C, then insert corner
the frame. If this is not done,
perpendicular to face of
B, followed by corner D, to
graphic will not fit into the
graphic. Insert narrow side
complete the installation of
frame correctly.
of welt with fabric to outside
the corners.
into the channel. Repeat for
other side of this corner.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work
toward
the
center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
w w w . c l a s s i c e x h i b i t s . c o m
- Assembly
TSV1
Lock
2
1
Graphic Removal
5
TSV1
Lock
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
TSV1
6
Lock
7
*
4
3
Bolt
TSV1
Lock
866.652.2100
TSV1 Lock Detail
Lock
TSP49
Tighten setscrew
to secure
extrusions
Mount Attachment
Z45
S10
7
V20's
*
Do not remove
bolts from V20's
Apply SEG graphic and position extrusion [7]
by loosening set screws, sliding into place, and
tightening set screws. S10 extrusion should
poke through hole in graphic. Loosen bolts on
iPad mount (Do Not Remove) and slide V20's
into S10 groove. tighten bolts to secure.
© 2014
Advertisement
Table of Contents
Related Manuals for Classic Exhibits SEGUE DESIGNS MOD-1363
Summary of Contents for Classic Exhibits SEGUE DESIGNS MOD-1363
- Page 1 Order# XXXXX - MOD-1363 - iPad Kiosk - Assembly 866.652.2100 Item Qty. Description 32.07” TSP49 Curved SEG Extrusion TSV1 Lock Detail 32.07” TSP49 Curved SEG Extrusion 32.07” TSP49 Curved SEG Extrusion TSV1 32.07” TSP49 Curved SEG Extrusion Lock 20”w TSP49 Horizontal SEG Extrusion Lock 20”w TSP49 Horizontal SEG Extrusion TSV1...
- Page 2 Order# XXXXX - MOD-1363 - iPad Kiosk - Assembly (Cont’d) 866.652.2100 Clamshell Lock Attachment Nuts Wire Management Attachment Lock Steps: 1) Run cords through plastic conduit. 2) Attach conduit where indicated by pinching the opening and inserting iPad Mounting Plate into the groove.
- Page 3 Order# XXXXX - MOD-1363 - iPad Kiosk - General Information 866.652.2100 Using Your Setup Instructions The Visionary Designs Setup Instructions are created specifically for your Detail A configuration. They are laid out sequentially, including an exploded view of the entire display, and then a logical series of detailed steps to assemble the main structure and components.
- Page 4 Order# XXXXX - MOD-1363 - iPad Kiosk - Packing Instructions 866.652.2100 Top View of Each Level Partly Assembled Frame Graphics Base Setup Hardware Level 1 Level 2 WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING ©...
Need help?
Do you have a question about the SEGUE DESIGNS MOD-1363 and is the answer not in the manual?
Questions and answers