Suisei RC-G4B Instruction Manual

Hide thumbs

Table Of Contents

Quick Links

Download this manual

RC-G4B

RC-G8B

Instruction

Manual

SUISEI ELECTRONICS SYSTEM CO., LTD.

Thank you for choosing RC-G4B/RC-G8B.

If you have any inquiry regarding the product, please contact us or our sales agency.

For your information, the content of this manual may change without prior notice.

Please check our website for the latest information;

1st Edition

http://www.suisei.co.jp.

Table of Contents

Need help?

Do you have a question about the RC-G4B and is the answer not in the manual?

Questions and answers

Summary of Contents for Suisei RC-G4B

Page 1 1st Edition SUISEI ELECTRONICS SYSTEM CO., LTD. Thank you for choosing RC-G4B/RC-G8B. If you have any inquiry regarding the product, please contact us or our sales agency. For your information, the content of this manual may change without prior notice.
Page 2 1st Edition : issued in March 2018 Copyright C 2018 Suisei Electronics System Co.,Ltd.  This product is a writing device only for one chip microcomputer with built-in flash ROM,EPROM and onetime PROM produced by Renesas Electronics Corporation. If can not be used for writing to other devices and for other purposes.
Page 3: Table Of Contents
Index Page １． Overview ..................................4 ２． Panel name, function description ......................6 ３． How to connect ..............................8 ４． Lighting pattern of Displayed LED ......................10 ５． T_VDD and T_VPP voltage setting switches ................10 ６． Connector for user target connection ....................11 ７．...
Page 4: １． Overview
RC-G4B/RC-G8B is a gang write unit that uses EFP-RC2 or EFP-LC and EFP-RC serial MCU programmers (Hereinafter EFP body) to connect 1 to 8 units. By using RC-G4B/RC-G8B, you can write and read at the same time up to 4 or 8 Renesas Electronics flash memory built-in MCU and QzROM built-in MCU.
Page 5 Figure 1.2 RC-G8B External Figures （5/13）...
Page 6: ２． Panel Name, Function Description
Connects EFP body, using EF1TGCB-16W16W. Connector User Target Connection Connects user target, using target connection cable. Connector It is an operation start switch. Start Switch It is connected to the external start input terminal of each EFP body. Figure 2.1 RC-G4B Panel Figure （6/13）...
Page 7 Mark Name Content Connect LED Lights when the EFP body is connect. (Green) Device LED(Orange) Lights up when device command is executed. When the result of device command execution ends Status LED normally, it will light up in "green". (Red/Green) When device command execution result ends in error, it lights up in "red".
Page 8: ３． How To Connect
３． How to connect Figure 3.1 and Figure 3.2 show how to connect the RC-G4B and RC-G8B. Mark Name Content RC-G4B RC-G4B main body EFP-RC2 EFP-RC2 main body (EFP-LC, EFP-RC can also be used.) Power adapter output : 19V, Current volume : 3.2A...
Page 9 Note1 : Please connect RC-G4B/RC-G8B and EFP body with the power supply turned off. Note2 : When the Device LED (Orange) of the RC-G4B/RC-G8B is lit, the connection cables to the EFP body and the user target board is energized, so do not insert / eject cables.
Page 10: ４． Lighting Pattern Of Displayed Led
Please set both 4BitQzROM and 8BitQzROM to 7.9V. Figure 5.1 Silk Figure of T_VDD and T_VPP voltage setting switch Note1 : When Device LED (orange) of RC-G4B/RC-G8B main body is turned on, please do not switch over T_VDD and T_VPP voltage setting switch.
Page 11: ６． Connector For User Target Connection
Output T_SCLK Clock for synchronous communications Output T_TXD Serial send data Input T_RXD Serial receive data Input T_Busy Target busy signal －（N.C） Output T_Reset Target reset control signal －（N.C） Note1 : I/O is the direction from RC-G4B/RC-G8B. （11/13）...
Page 12: ７． How To Operate
７． How to operate Below are a series of operation methods of RC-G4B/RC-G8B. When EFP-RC2 or EFP-RC is used for RC-G4B/RC-G8B, it is necessary to set to memory execution mode. How to set the memory execution mode is described in the following items.
Page 13: ８． Specifications
８． Specifications Table 8.1 Specifications External dimensions RC-G4B 140(W)×140(D)×70(Ｈ) [mm] (Protruding parts not included) RC-G8B 140(W)×140(D)×95(Ｈ) [mm] RC-G4B About 879ｇ Weight RC-G8B About 1091ｇ Supported programmer EFP-RC2、EFP-LC、EFP-RC 8.1 Notes Products of the following serial No. can not be used with this device.

This manual is also suitable for:

Rc-g8b