Ingenic USBCloner Quick Manual

The burn tool

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Ingenic®

USBCloner The Burn tool Quick Guide

Date: July. 2017

Table of Contents

Need help?

Do you have a question about the USBCloner and is the answer not in the manual?

Questions and answers

Summary of Contents for Ingenic USBCloner

Page 1 Ingenic® USBCloner The Burn tool Quick Guide Date: July. 2017...
Page 2 Ingenic Terms and Conditions of Sale. Ingenic products are not designed for and should not be used in any medical or life sustaining or supporting equipment. All information in this document should be treated as preliminary. Ingenic may make changes to this document without notice.
Page 3: Table Of Contents
5.7 Progress appears as failed Boot stage 85%..................19 5.8 Progress appears as failed Boot stage 100%，But burning files by 0%..........19 5.9 Other errors............................19 USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 5: Overview
USBCloner The Burn tool Quick Guide Overview USBCloner burn tool is based on a new code framework developed. This document describes the burning process of USBCloner burn tool that to avoid unnecessary use of questions. Operating environment support USBCloner supportted the systems as follows: 1）Windows XP、Win7 and above version（32bit,64bit);...
Page 6: Install The Driver
USBCloner The Burn tool Quick Guide Install the driver USBCloner has Linux and Windows version. on Linux, USBCloner do not need to install the driver. Therefore, this section was for Windows XP, for example, this paper introduces Windows host driver installation steps.
Page 7 Figure 2-1 identification devices  Right click on the current USB device and select update driver software to pop up, as shown in Figure 2-2 USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 8  Select "browse the computer to find driver software", pop up like figure 2-3, click browse, and then select the drive directory cloner-win32-driver in the downloaded burn tool unpack directory USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 9 USBCloner The Burn tool Quick Guide Figure 2-3 selecting the drive path  Then click OK, and then click "next" to drive the installation successfully, as shown in figure 2-4. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 11: Run The Burn Tool
$ ./cloner 2.2 Windows Unzip the downloaded cloner-x.x.x(version numbe)-windows_release.zip and enter the Cloner-version numbe-Windows directory, double-click the "Cloner" run the Burn tool as in Figure 3-1. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 13: Burn Process
Power Off ------System power off after the burn is complete(When the factory burn choose to use in more ) 3.2 Modify the policy After you choose the Platform and Board, according to your actual needs to modify the USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 14: Modify The Policy
When the Nand burn, should first be partitioned. Used MTD burn, the "offset" is the partition name. 3.3 Save current configurations Policy setting is completed, click "Save" to save the current settings as in Figure 4-3. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 16: Add Configurations
You modify the configuration according to your actual needs. If you do not want to replace the default configuration, click on the "Save as" to save it as in Figure 4-4. Figure 4-4 Save profile as USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 17: Burn Sample
Figure 5-1 Information configuration interface 4.2 Modify the policy Click configure "policy" tabs, enter policy configuration interface shown in Figure 5-2. Burn on burning mirrors offsets and path settings USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 18 Set the image path: Click on the need to modify the policy in the "settings" item, pop-up interface shown in Figure 5-3, select burn image file. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 19: Save Current Configurations
Figure 5-3 Select burn image file 4.3 Save current configurations When you have finished setting policies, click "Save" to save the current configuration information as in Figure 5-4. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 20: Burn
2. Press the development board of USB burn mode button.Make development board also can burn into the burning state.  In the process of burning all the progress bar reaches 100% buffer and complete as shown in figure 5-5. USBCloner The Burn tool Quick Guide Copyright® 2005-2015 Ingenic Semiconductor Co., Ltd. All rights reserved.
Page 22: Faq
Some of the common problems and solutions. 5.1 Windows driver installation failures If you use the Burn tool environment is Windows and install the usbcloner driver fail, please make the following checks: 1. Confirm whether development boards into the USB boot mode.
Page 23: Progress Appears As Failed Boot Stage 50%, 70%, 75
If the main screen displays the progress bar turns red and the progress to 50% or 70% or 75% .Then check the DDR configuration.If DDR configurations are correct, then check the USBcloner operating environment whether an identified USB virtual machine.