Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for KS THERMAL-i
- Page 1 KS Technologies USER MANUAL...
-
Page 2: Table Of Contents
Device Overview ......................5 Starting a Thermal Profiling Session ................6 Standalone Mode......................6 Status LED’s ....................... 6 Charging ........................6 Using the Thermal-i Interface ..................7 Thermal-i Viewer Software................8 Software Overview ...................... 8 System Requirements ....................8 Software Installation ....................8 Menu’s and Navigation .................... -
Page 3: Disclaimer
PVC foils onto MDF panels. The device is not to be used for any other purpose unless it’s suitability has been assessed and confirmed by KS Technologies. -
Page 4: Precautions
The maximum pressure to be applied is 6.0 bar. WARNING: If a pin system is present on the thermoforming press, ensure no pins are activated under the Thermal-i profiler as this may cause a puncture or damage to the base of the profiler. -
Page 5: Warranty
Warranty KS Technologies Limited warrants this product against defects in material or workmanship for a period of 1 year from the date of shipment. At the discretion of KS Technologies Limited, the product will either be replaced or repaired. The warranty does not cover damage caused by accidental or intended misuse, abuse, modification or misapplication. -
Page 6: Getting Started
Getting Started Device Overview The Thermal-i profiler incorporates various sensors to monitor the variable conditions present within the thermoforming pressing chamber. The values for these sensors can be monitored directly from the profiler, as well as using the Thermal-i Viewer software. -
Page 7: Starting A Thermal Profiling Session
Standalone Mode The Thermal-i can be used in standalone mode without the need for a PC. To use the device in this mode, select Peak Readings in the main menu of the device. Prior to a thermoforming cycle, press Reset to reset the peak values to current values. -
Page 8: Using The Thermal-I Interface
M A N U A L Using the Thermal-i User Interface Main Menu The main menu will load shortly after the Thermal-i is powered on. When connected and logging to a PC, this menu will be disabled and ‘Connected to PC’ will be displayed. -
Page 9: Thermal-I Viewer Software
The Thermal-i Viewer software has been designed to streamline the process of communicating and logging data from the Thermal-i range of temperature dataloggers. The interface has been optimized for use with Windows PC’s and tablets and is suitable for use with touchscreen displays. -
Page 10: Menus And Navigation
Menus and Navigation The main screen provides the user with full control of the Thermal-i. It allows the user to start a logging session, turn the camera and lights on/off and start/stop a recording. The thermal logging graph is shown in the left window and the video feed is shown in the right window. -
Page 11: Application Settings
IP address for the Thermal-i 10.10.1.1 Thermal IP Port Port address for the Thermal-i 8150 Video IP IP address for the Thermal-i video feed 10.10.1.1 Video IP Port Port address for the Thermal-i video feed 8196 Range Temperature range of the thermal axis on graph 0>150 C... -
Page 12: Device Specification
T H E R M A L - I U S E R M A N U A L Device Specification Mechanical Characteristics 365mm x 215mm x 34mm Dimensions (L x W x H) Weight 3.2kg (Without Carry Case) Internal and Battery Charging: 0 to 45 ̊... -
Page 13: Troubleshooting
1) If an external sensor, ensure that it is clean and Dirty or faulty sensor readings free from dirt If a fault is not listed above, or if you are unable to resolve the issue, please contact KS Technologies Limited for further assistance. -
Page 14: Declaration Of Conformity
T H E R M A L - I U S E R M A N U A L... - Page 15 T H E R M A L - I U S E R M A N U A L www.kstechnologies.co.uk Email: Info@kstechnologies.co.uk...
Need help?
Do you have a question about the THERMAL-i and is the answer not in the manual?
Questions and answers