Download Print this page
Changhong Electric S-CK Series User Manual
Changhong Electric S-CK Series User Manual

Changhong Electric S-CK Series User Manual

Foldable black grid screen front projection material

Advertisement

Quick Links

Changhong S-CK Series Foldable Black Grid Screen
Product Description:
The S-CK Series is an ultra-short throw fixed frame projection screen (Foldable) that uses black grid material
technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light
cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.
Screen Maintenance
Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image.
For optimal results we advise to pay attention to the following instructions.
1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular motion.
Wipe from left to right only.
2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may damage
the screen's surface).
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.
Notes:
The following precautions should be followed at all times to avoid damaging the material, which is not
covered under warranty.
Don't
touch
the screen material to avoid leaving fingerprints. Use gloves when handling the material.
U
U
Don't
scratch
the material, as it will leave permanent markings on the screen's surface.
U
U
Don't
point
to the screen material with a fingertip or other sharp objects to prevent damage to the material.
U
U
Don't use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such
chemicals will permanently damage the screen.
Front Projection Material
User's Guide
Laser.changhong.com
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the S-CK Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Changhong Electric S-CK Series

  • Page 1 User’s Guide Product Description: The S-CK Series is an ultra-short throw fixed frame projection screen (Foldable) that uses black grid material technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.
  • Page 2: Frame Assembly

    Hardware and Parts List Please make sure all parts listed below are included before installation. B. Top/Bottom horizontal frame A. Elbow joint x4 pcs C. Left/Right vertical frame x2 pcs D. Center joints x2 pcs x4 pcs E. Center support bar x1-2 pcs F.
  • Page 3 5. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below. Elbow Joint (A) Elbow Joint (A) Horizontal long frame (B) Push 6. Insert the two vertical short frames (C) into the elbow joint (A). Horizontal long frame (B) push push...
  • Page 4 Then fasten the four angles with the M5x16 Screws (G). Four corners join correctly to form a perfect rectangle. Use screwdriver to fasten the M5x16 screws (G) into each corner by aligning the frame screw holes to the holes in the elbow joint (A). Laser.changhong.com...
  • Page 5 Screen Material Installation Please read this important note before proceeding with the installation process of the material: Before handling the Black Grid material, put on the supplied pair of white gloves to avoid leaving fingerprint marks, dust or hand oil on the material’s surface (Figure 1). The Black Grid material is very delicate and should be handled with extreme care.
  • Page 6 5. After all of the corners of the frame have been properly aligned (example D), attach the material on the frame in the following order A→B→C→D (see instructions below for details). Attach the screen material to the corners as shown below. 1) Stretch the screen material in 3) Fold over second side 4) Repeat until all four sides...
  • Page 7 Grasp the middle of the screen material and attach it to the Velcro strip on the frame Lay the Velcro end on the screen material over the Velcro end of the frame and keep it within the edge. ①② Proceed in the following sequence The key is to attach within the middle sections of 1 and 2.
  • Page 8 Pull back the screen material from the Velcro connection along the edges of the frame to detach it. Support bar installation: 1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar with the M6 hex step nut (H) on the top and bottom frames.
  • Page 9 Edge trim Installation Included is an black edge trim that provides an elegant ultra-thin bezel finish Edge trim x 6 PCS Plastic corner sleeve x4pcs Black tape x1pcs 1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. a.
  • Page 10 The front side of the frame with trim pieces attached. Corner gap will be covered by Figure 3 the corner sleeve (M). 4. After the bezel trim has been installed, place a corner sleeve (M) on all four corners. Begin by aligning and adjusting the corner sleeve through the front of the screen.
  • Page 11 Proper Projector Placement for Changhong S-CK Series The Changhong S-CK Series is exclusively for table-mounted ultra-short throw projectors as illustrated in example 1 below. Overhead placement or a standard projector will make the image very dark, on account of the screen’s absorbent layer deflecting light that is not aligned with its reflective angle.
  • Page 12 Installation 1. Correctly distinguish the top and bottom of the screen: Place the assembled screen vertically on the ground. Look down on the screen, if the material is black it is in the correct direction and ready for mounting on the wall. However, if the material is white, turn around the screen and then install it.

This manual is also suitable for:

S100ck