Page 1 | Motor Grader Operator’s Manual , 201 Part # S/N: Tier 65ET...
Page 2 This page intentionally left blank.
Page 3: Table Of Contents
NORAM 65ET GRADER ABLE OF ONTENTS Every 100 Hours ......... 4-21 AFETY Every 250 Hours or Monthly ....4-23 Safety Messages ........1-1 Every 500 Hours or 3 Months .... 4-26 Safety Symbol Explanation ....1-2 Every 500 Hours or 6 Months .... 4-30 Safety Decal Locations ......
Page 4: Table Of
NORAM 65ET GRADER PECIFICATIONS Options ..........7-15 ROUBLESHOOTING Engine ............8-1 Transmission .........8-1 Hydraulics and Implements ....8-2 2 Table of Contents NORAM 65ET GRADER...
Page 5: Afety
NORAM 65ET GRADER 1: S ECTION AFETY AFETY ESSAGES General safety messages appear in this Safety Messages section. Specific safety messages are located in appropriate sections of the manual where a potential hazard may occur if the instructions or procedures are not followed.
Page 6: Safety Symbol Explanation
NORAM 65ET GRADER AFETY YMBOL XPLANATION This is the safety alert symbol. This symbol is used in combination with an exclamation mark or other symbols to alert you to the potential for bodily injury or death. Read Operator’s Manual and safety signs before operating machine.
Page 7 NORAM 65ET GRADER Refer to and follow the Shutdown Procedure before servicing, cleaning, repairing, or transporting machine. Pressurized fluid can penetrate body tissue and result in serious injury or death. Leaks can be invisible. Keep away from any suspected leak. Relieve pressure in the hydraulic system before searching for leaks, disconnecting hoses, or performing any other work on the system.
Page 8 • Make no modifications to your equipment unless specifically requested by NorAm. • No riders allowed on machine. Only a seated operator, with seat belt securely fastened, is per- mitted on the machine during grading operation or when roading between job sites.
Page 9 40°F (5°C). The mounting surface must also be clean and dry. • When replacing a machine component with a decal attached, replace the decal also. • Replacement decals can be purchased from your NorAm dealer. Check Laws And Regulations Know and obey all federal, state, and local laws and regulations that apply to your work situation.
Page 10: Safety Decal Locations
NORAM 65ET GRADER AFETY ECAL OCATIONS Safety Decal Locations...
Page 11: General Information
Read this manual carefully and keep it tethered to the manual holder on the machine for future reference. If at any time a question arises concerning the equipment, contact an authorized NorAm dealer. Factory trained personnel, genuine replacement parts and the necessary equipment are available for all service requirements.
Page 12: Orientation
NORAM 65ET GRADER RIENTATION References are made throughout this manual to describe location and direction. Unless otherwise specified, reference to direction is from the operator's seat. ACHINE ESCRIPTION The grader is a construction machine with a long moldboard blade used to create a flat surface during the grading process.
Page 13: Identification Numbers
NORAM 65ET GRADER DENTIFICATION UMBERS The motor grader and major components are identified by serial numbers. The serial numbers are required when ordering parts. For easy reference the identification data should be recorded and kept in a safe place away from the machine.
Page 14 NORAM 65ET GRADER The differential identification plate is located on the right tandem support. The transmission identification plate is located on the front side of the transmission below the drive shaft. Identification Numbers...
Page 15: Component Identification And Locations
NORAM 65ET GRADER OMPONENT DENTIFICATION AND OCATIONS DO NOT operate machine until thoroughly familiar with the location and operation of all controls. Protective Shield The engine and transmission are enclosed to protect personnel from hot and moving parts. An additional guard encloses the cooling fan.
Page 16 NORAM 65ET GRADER When equipped with the engine, opening the left side engine Cummins QSF3.8 Tier 4 Final compartment door provides access to the following: Cummins QSF3.8 Tier 4 Final Electronic Control Module (ECM) Fuel Pump Crankcase Breather Oil Fill...
Page 17 NORAM 65ET GRADER When equipped with the engine, opening the right side engine Cummins QSF3.8 Tier 4 Final compartment door provides access to the following: Cummins QSF3.8 Tier 4 Final Air Filter Indicator SCR System Hydraulic Tank Filter Heater Core Shutoff Valve...
Page 18 NORAM 65ET GRADER When equipped with the engine, opening the left side engine compartment CAT C3.4B Tier 4 Final door provides access to the following: CAT C3.4B Tier 4 Final Engine Electronic Control Module (ECM) Fuel Primer Glow Plug Control Unit (GPCU)
Page 19 NORAM 65ET GRADER When equipped with the engine, opening the right side engine CAT C3.4B Tier 4 Final compartment door provides access to the following: CAT C3.4B Tier 4 Final Hydraulic Tank Filter NOx Sensors Hydraulic Filter Gauge Ammonia Sensor (on back of panel)
Page 20 NORAM 65ET GRADER The radiator access door is located on top of the engine cover. The hydraulic reservoir fill cap and transmission oil fill and dipstick are located behind the right side engine access door. The fuel fill neck and DEF fill neck are located behind the left side access door.
Page 21 NORAM 65ET GRADER Lock Pins Lock pins are provided to prevent unintended movement of components during maintenance or transport. The articulation lock pin prevents articulation. Store the pin in the storage bracket during operation. The wheel lean lock pin prevents side-to-side movement of the front steering wheels but does not prevent steering.
Page 22 NORAM 65ET GRADER Lighting Two work lights are mounted on the front frame facing the moldboard. Two headlights, turn signals, and hazard lights are mounted at the front of the machine. Two optional work lights may be mounted on the top of the cab facing forward.
Page 23 NORAM 65ET GRADER Operator’s Door (Cab-Equipped Models) Lockable doors are provided on both sides of the cab. Rotate the key toward the door to lock or rotate the key away from the door to unlock. To open a door from the outside, push in the button and pull the door open.
Page 24 NORAM 65ET GRADER Heating (Cab-Equipped Models) The three-speed heater fan is controlled by a Rotary Switch . Rotate the switch one notch clockwise, to operate fan in LOW speed. Turn clockwise to increase speed to MEDIUM, and HIGH speeds. Rotate fully counterclockwise to turn OFF heater fan.
Page 25 NORAM 65ET GRADER Seat Seat Adjustments The seat should be adjusted before operating the machine so all controls are easily reached and the operator is comfortable with good visibility. 1. Height Adjustment - Pull out to lower seat. Push in to raise seat.
Page 26 NORAM 65ET GRADER Seat Belt This machine is equipped with a Rollover Protective Structure (ROPS) and seat belt. The operator must wear the seat belt when operating the machine. The seat belt helps hold the operator inside the protected area of the ROPS. Failure to wear the seat belt could result in the operator being thrown from the seat and crushed if a rollover occurs.
Page 27 NORAM 65ET GRADER Front Console Front Console Indicator Lights The front console contains two indicator lights that provide information on the status of the headlights. Light indicates high beam is ON. Light indicates the head lights are ON. Saddle Pin Puller Switch (Optional)
Page 28 NORAM 65ET GRADER Hazard Lights Switch Switch controls the hazard lights. Press top of switch to turn ON hazard lights. Press bottom of switch to turn OFF hazard lights. Follow federal, state and local laws regarding NOTE: road travel of slow-moving vehicles and construction equipment.
Page 29 NORAM 65ET GRADER Implement Switch (Optional) The optional Implement Switch changes the Scarifier Lever to the Ripper Lever. To select the Scarifier Option, press the top of the switch. To select the Ripper Option, press the bottom of the switch.
Page 30 NORAM 65ET GRADER Front Console Lock Lever Lever prevents the movement of the implement, moldboard, articulation and wheel lean levers, and front console. All levers must be in a neutral position to engage implement lock. The console must be tilted forward to allow the implement lock to engage.
Page 31 NORAM 65ET GRADER Standard Style Control Configuration Applies to all machines except for machines with the CAT control option. NOTE: Implement Control Lever Lever operates the optional front and rear mounted implements. NOTICE: Front and rear mounted implements each have a lock pin which must be removed manually to raise and lower the implement, otherwise equipment damage will result.
Page 32 NORAM 65ET GRADER Articulation Control Lever Lever operates the articulation cylinders, causing the center of the motor grader to pivot. Front Wheel Lean Control Lever Lever controls the angle of the front wheels. Front wheel lock pin must be manually NOTE: removed before leaning wheels.
Page 33 NORAM 65ET GRADER Caterpillar Style Control Configuration Only applies to machines with the CAT control option. NOTE: Left Side Moldboard Height Control Lever Lever raises, lowers or floats the left side of the moldboard. Side Shift Control Lever Lever shifts the moldboard side to side or, if the blade pitch switch is activated, changes the pitch of the moldboard.
Page 34 NORAM 65ET GRADER Articulation Control Lever Lever pivots the motor grader frame. Front Wheel Lean Control Lever Lever controls the angle of the front wheels. Front wheel lean has a lock pin which must NOTE: be removed manually to actuate wheel lean.
Page 35 NORAM 65ET GRADER Right Side Console Throttle Control Lever Lever controls engine speed. Move the lever rearward to decrease engine speed or forward to increase engine speed. Transmission Control Lever The transmission will not shift into gear if NOTE: the parking brake is applied. A message that the park...
Page 36 NORAM 65ET GRADER Work Lights Two switches control the work lights. The Front Work Lights Switch , a two-position switch, controls the front work lights mounted on the front frame and optional work lights mounted on the canopy or cab. The...
Page 37 NORAM 65ET GRADER Floor and Ceiling Controls Brake Pedals Two pedals , linked together, control the service brake. The pedals are linked together so either one or both, can be depressed to activate the brakes. If the Inching Control Switch is off, depressing a brake pedal also disengages the transmission when in 1st, 2nd, and 3rd gear.
Page 38: Electronic Display
NORAM 65ET GRADER LECTRONIC ISPLAY The system incorporates gauges and diagnostics with a LCD (Liquid Crystal Display) of current readings through which the operator may scroll. Indicator Lamps The indicator lamps illuminate whenever engine or machine errors are active, engine is in a stop/derate state, fuel level is low, or DEF level is low.
Page 39 NORAM 65ET GRADER Main Operating Screen 1. Transmission Gear 2. Engine RPM 3. Fuel Level When fuel level is < 5% the right amber NOTE: indicator lamp is illuminated. 4. Menu - Press Control Key associated with icon to enter Menu Screen.
Page 40 NORAM 65ET GRADER High exhaust temperatures during a regeneration cycle. 7. Regeneration / After-Treatment System Cleaning In- Progress - Displays icon when a regeneration in-prog- ress cycle is active. Regeneration is controlled auto- matically by the engine, unless inhibited by operator input.
Page 41 NORAM 65ET GRADER Menu Screen Down arrow moves selection box down. Up arrow moves selection box up. Right arrow enters selected screen. exits to previous screen. Highlight screen name of choice and select by pressing Control Key associated with the right arrow option.
Page 42 NORAM 65ET GRADER View Engine Diagnostics 2 Screen View Engine Diagnostics 2 Screen displays the following: • Battery • Manifold Temperature • Engine Model • DEF Level • DEF Temperature • Hest Lamp • Inhibit Lamp • Force Lamp • SCR Cleaning Lamp •...
Page 43 NORAM 65ET GRADER View CAN Screen View CAN Screen displays the following: • CAN conditions • Power in Volts • Current Software Revision If a problem is present in the CAN system, TCU, ECM or display and an entity is not connected to the CAN system, the line above the entity will not be present.
Page 44 NORAM 65ET GRADER Contrast Adjustment The Contrast Adjustment Option allows the user to change the contrast of the display screen. To activate, press the Control Keys associated with the up or down arrows, followed by the right arrow to select desired setting.
Page 45 NORAM 65ET GRADER AEB Mode Request The AEB serves to compensate tolerances (plate clearance and pressure level), which are influencing the filling procedure of the transmission clutches. Before activating AEB Mode it is necessary to: • turn Inching “ON (1)”...
Page 46 NORAM 65ET GRADER The “Top Left”, “Top Right”, “Bottom Left”, and “Bottom Right” system settings screens allow the user to customize the Main Operating Screen – Top Left – Top Right – Bottom Left – Bottom Right 2-36 Electronic Display...
Page 47 NORAM 65ET GRADER The following monitored engine and transmission parameters are available. Battery Voltage Fuel Pressure Hours Transmission Oil Temperature Engine RPM Coolant Temperature (Metric) Percent Load (Engine) Oil Pressure (Metric) Coolant Temperature Manifold Temperature (Metric) Oil Pressure Boost Pressure (Metric)
Page 48 NORAM 65ET GRADER View Errors Screen View Errors Screen displays: • Active Error Count • Active Error Occurrences • Display Voltage High • SPN Error Code • FMI Error Code • OC (Number of Occurrences) Active Error Screen The Active Error Screen will be displayed at start-up if an error is active and during normal operation if an error becomes active.
Page 49 NORAM 65ET GRADER Electronic Display Navigation 2-39 Electronic Display...
Page 50 NORAM 65ET GRADER 2-40 Electronic Display...
Page 51 NORAM 65ET GRADER 2-41 Electronic Display...
Page 52 NORAM 65ET GRADER 2-42 Electronic Display...
Page 53 NORAM 65ET GRADER 2-43 Electronic Display...
Page 54 This page intentionally left blank.
Page 55: Mounting And Dismounting
NORAM 65ET GRADER 3: O ECTION PERATION OUNTING AND ISMOUNTING Use steps and handholds and face machine whenever mounting or dismounting the machine. Maintain a three-point contact with the steps and with the handholds. DO NOT get on or off a moving vehicle.
Page 56: Daily Pre-Starting Inspection
NORAM 65ET GRADER Check the following fluid levels: Clean around fill caps before removing. NOTE: • engine oil, • coolant, • fuel, • Diesel Exhaust Fluid (DEF), and • hydraulic oil. NOTICE: Accumulated grease and oil on a machine is a fire hazard. Remove the accumulated grease and oil.
Page 57: Rollover Protective Structure (Rops)
ROPS. Under no circumstances may total gross weight of machine exceed weight specified on ROPS label. If ROPS must be replaced, be sure to use original parts ordered from NorAm. If rollover occurs: • Brace yourself and stay on the machine. Keep the seat belt fastened.
Page 58 NORAM 65ET GRADER Machine Starting Procedure Preparing to Start Engine Diesel engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.
Page 59 NORAM 65ET GRADER Starting Engine 1. Insert key in the Ignition Switch and turn clockwise to “START”. Hold in position until engine starts or for a maximum of 30 seconds, whichever occurs first, and release to the “RUN” position. 2. If engine does not start within 30 seconds, wait two minutes to allow starter to cool before repeating.
Page 60 NORAM 65ET GRADER Machine Shutdown Procedure Before stopping the engine, idle engine for 3 to 5 minutes to allow turbocharger and manifold to cool and prevent possible distortion of components. To stop engine: 1. Move Transmission Control Lever to NEUTRAL.
Page 61 NORAM 65ET GRADER Engine Speed Setting Engine Speed Engine speed is set using the Throttle Control Lever located on the right side console. Move lever rearward to decrease engine speed or forward to increase engine speed. The Throttle Control Lever can be positioned as desired between low idle and high idle.
Page 62: Driving The Machine
NORAM 65ET GRADER RIVING THE ACHINE Observe the following precautions when driving the motor grader: • Never coast machine with transmission in neutral. • Select proper gear before starting up or down a hill. for downhill use the same gear or lower as would be used to go uphill.
Page 63 NORAM 65ET GRADER Steering The basic method of steering the motor grader is through the front steering wheels. The turning radius can be reduced by using the front wheel lean and frame articulation. Whenever negotiating a sharp turn, reduce the speed before entering the turn.
Page 64 NORAM 65ET GRADER Articulation NOTICE: An articulation lock pin under the cab must be removed and placed in storage bracket before operating. DO NOT operate machine with articulation lock pin installed. The motor grader has an articulating frame. Articulating the frame toward the inside of a turn greatly reduces the turning radius, allowing operation in tight quarters.
Page 65: Moldboard And Implement Operation
NORAM 65ET GRADER OLDBOARD AND MPLEMENT PERATION The moldboard and optional implements are hydraulically operated. Control levers are located on each side of the front console. By actuating a switch on top of the front console, some control levers operate multiple functions.
Page 66 NORAM 65ET GRADER The Implement Control Lever raises and lowers the selected implement. The front of the motor grader may be equipped with a scarifier or blade, and the rear of the machine may be equipped with a ripper. DO NOT engage the ground with the front NOTE: and rear implements at the same time.
Page 67 NORAM 65ET GRADER Moldboard Side Shift The Moldboard Side Shift Lever moves the moldboard side to side. The side shift function adjusts moldboard position without changing the relative grade angle. Shift the moldboard to one side to: • Prevent tires from traveling too close to an edge.
Page 68 NORAM 65ET GRADER Manual Moldboard Pitch Adjustment 1. Lower moldboard to the ground and apply Parking Brake. Moldboard should rest lightly on ground with no downward pressure. 2. Pull hairpin clip and remove pin from pitch adjuster link. Moldboard may fall forward and strike and injure you when pitch adjuster link pin is removed.
Page 69 NORAM 65ET GRADER Moldboard Angle The angle of the moldboard determines the swath (cutting width) of the moldboard and the amount of material moved. A greater angle decreases the swath of the moldboard but allows material to discharge faster and decreasing the load. Most operations require a moldboard angle of between 15°...
Page 70 NORAM 65ET GRADER Moldboard Height The height of the moldboard is adjusted through a Right Side Height Control Lever and a Left Side Height Control Lever . The levers are adjacent to one another to allow one-handed operation when moving both ends of the moldboard.
Page 71 NORAM 65ET GRADER Saddle Lock Pin (Optional) To allow grading on banks up to 90° an optional rotating saddle is available. A hydraulically operated lock pin secures the saddle to the front module frame. When released the saddle rotates, allowing the circle and moldboard to pivot for side grading.
Page 72 NORAM 65ET GRADER Bank Slope (Optional) When the motor grader is equipped with the optional rotating saddle, the moldboard can be rotated 90° to either side for grading steep slopes. To rotate saddle and moldboard to the right: 1. Rotate circle...
Page 73 NORAM 65ET GRADER Power-Shift Transmission The power-shift transmission uses a single control lever . Six forward and two reverse gear ratios may be chosen to provide the correct operating speed for any condition. With the Inching Control Switch deactivated, depressing the brake pedal disconnects the transmission.
Page 74 NORAM 65ET GRADER Inching Control If brake pedal is depressed and the Inching Control, displayed on the screen, is deactivated, the transmission will disconnect and will not transfer power to the wheels. The transmission will engage when the brake pedals are released.
Page 75 NORAM 65ET GRADER Digging Electricity or gas explosion can kill. Laser light in cut cable can result in eye damage. Locate utilities before digging. Call 811 (U.S. only) or 1-888-258-0808 (U.S. or Canada) or local utility companies or national regulating authority.
Page 76 NORAM 65ET GRADER Leveling and Smoothing NOTICE: Never push material with the back of the blade. Back dragging will increase wear on the cutting edges and may damage exposed cylinder rods. When leveling an area of loose material, such as a road bed, straighten the frame and center the circle under the machine.
Page 77 NORAM 65ET GRADER Moving a Disabled Machine When hauling or towing motor grader insert wheel lean lock pin and articulation lock pin. Whenever possible, move a disabled machine using a transport trailer. If this is not possible the motor grader can be towed short distance to a more suitable site for field service.
Page 78 This page intentionally left blank.
Page 79: Lubrication And Maintenance - Grader Components
NORAM 65ET GRADER 4: L ECTION UBRICATION AND AINTENANCE RADER OMPONENTS AFETY ESSAGES Read the Operation and Maintenance Manual and safety signs before performing maintenance on the machine. Wear personal protective equipment. Dress properly. Wear close fitting clothing and confine long hair. Avoid wearing jewelry such as rings, wrist watches, necklaces or bracelets.
Page 80 NORAM 65ET GRADER Raised attachment can fall and crush you. Never work under a raised attachment unless attachment is securely supported with suitable blocking or cylinder stops. Hot fluid under pressure can scald. Allow engine to cool before opening radiator cap.
Page 81 NORAM 65ET GRADER Explosion and separation of a tire or rim parts can cause serious injury or death. • Use a clip-on air chuck with an in-line pressure gauge and a remote air valve that allows you to stand behind the tread when inflating a tire.
Page 82: General Information
NORAM 65ET GRADER ENERAL NFORMATION Proper machine operation depends upon a properly maintained machine. This section provides a list of items to be checked, inspected or changed periodically. Section 4 includes machine lubrication and maintenance instruction but excludes engine NOTE: lubrication and maintenance instruction.
Page 83 NORAM 65ET GRADER Service Intervals The recommended intervals should be adjusted when operating in severe conditions. Time intervals should be checked when the machine reaches either the number of hours or the time allotment, whichever comes first. As an example, if the motor grader has accumulated 1200 hours and a year has passed since hydraulic oil was replaced, change the hydraulic oil now rather than waiting until 2000 hours have passed.
Page 84: Accessing Lubrication And Check Points
NORAM 65ET GRADER CCESSING UBRICATION AND HECK OINTS In order to access many of the lubrication and check points during service and maintenance procedures, shielding will need to be removed and the hood opened or removed. After service and maintenance work is complete, shielding must be reinstalled before operating the machine.
Page 85 NORAM 65ET GRADER Lubrication/Fluid Level Check LUBRICATION / FLUID LEVEL CHECK - 65ET T4 FINAL Interval No. of Type of Identification Remarks Hours Lube Ultra Low Sulfur Fuel Tank Fill Diesel (ULSD) Every 10 ISO 22241 DEF Tank Fill Hours or...
Page 86 NORAM 65ET GRADER LUBRICATION / FLUID LEVEL CHECK - 65ET T4 FINAL Interval No. of Type of Identification Remarks Hours Lube Universal Joints One on universal joint at Shots (Drive Shaft) each end of drive shaft. Every Rear Axle 5.5 Gal...
Page 87 NORAM 65ET GRADER Accessing Lubrication and Check Points...
Page 88: Maintenance Intervals
NTERVALS The maintenance intervals outlined in the following maintenance section are based on normal operating conditions. When operating under severe conditions, the maintenance intervals should be shortened. SERVICE HOURS - 65ET T4 FINAL Interval Hours Identification Remarks Every 10 Hours...
Page 89 NORAM 65ET GRADER SERVICE HOURS - 65ET T4 FINAL Interval Hours Identification Remarks Washer Fluid Fill Parking Brake Cable Adjust (Transmission End) Parking Brake Cable (Lever Adjust End) Parking Brake Switch Adjust / Replace Radiator / Oil Cooler Check When Required...
Page 90: Every 10 Hours Or Daily
NORAM 65ET GRADER 10 H VERY OURS OR AILY Fuel - Check / Add Fuel and fumes can explode and burn. Shut off engine before refueling. No flame. No smoking. • DO NOT smoke around diesel fuel. • DO NOT add gasoline, alcohol, gasohol or dieselhol (a mixture of diesel fuel and alcohol) to die- sel fuel because of increased fire or explosion risks.
Page 91 NORAM 65ET GRADER Diesel Exhaust Fluid (DEF) - Check / Add Use caution when dispensing DEF near an engine that has recently been running. Spilling DEF onto hot components may cause the release of ammonia vapors. DO NOT breathe ammonia vapors. DO NOT clean up any spills with bleach.
Page 92 NORAM 65ET GRADER Hydraulic Oil - Check Check the hydraulic oil level in the reservoir with engine off. A sight gauge is located inside the right side of the engine cover. Oil level should be between the marks of the glass when the engine is off.
Page 93 NORAM 65ET GRADER Radiator Coolant - Check Hot fluid under pressure can scald. Allow engine to cool before opening radiator cap. Check the coolant level when the engine is stopped and cool. Coolant should be kept off skin. Follow instructions on coolant filter and antifreeze container.
Page 94 The backup alarm should continue to sound until the propel lever is moved to the NEUTRAL position or to the FORWARD position. 3. Contact a NorAm dealer if backup alarm does not function properly. 4-16 Every 10 Hours or Daily...
Page 95: Every 50 Hours Or Weekly
NORAM 65ET GRADER 50 H VERY OURS OR EEKLY Front Axle Drag Link - Grease One fitting on each side of front axle. 2-4 shots each. Moldboard Lift Cylinder Balls - Grease One fitting on lower end of each lift cylinder. 2-4 shots each.
Page 96 NORAM 65ET GRADER Front Axle Pivot Pins - Grease One fitting on front axle pivot pin. 2-4 shots. Steering Cylinder - Grease One fitting on each end of steering cylinder. 2-4 shots each. Front Axle Knuckle Pivot - Grease One fitting on each of two front axle knuckle pivots.
Page 97 NORAM 65ET GRADER Moldboard Pitch Adjustment - Grease One fitting on each end of moldboard pitch cylinder or optional manual adjuster rod. 2-4 shots each. Implement Lift Cylinders - Grease One fitting located on each end of any implement cylinders installed. 2-4 shots each.
Page 98 NORAM 65ET GRADER Moldboard and Circle Turn - Clean / Lubricate Grease and clean moldboard slide bars and circle turn with graphite paint. Wheel Lug Nuts - Check Check to ensure wheel lug nuts are installed and tight on all wheels. Use a torque wrench to verify the front and rear wheel lug nuts are torqued to 440–475...
Page 99: Every 100 Hours
5. Return propel lever to NEUTRAL. 6. Start the engine. 7. Contact a NorAm dealer if propel lever neutral start interlock does not function properly. Propel Lever Interlock Button - Test Serious injury or death can result if machine moves and strikes a bystander.
Page 100 2. Start engine. 3. Turn inching control ON. 4. Place machine in first gear. 5. Increase engine speed to full throttle. Machine must not move. NOTE: 6. Contact a NorAm dealer if foot brake does not function properly. 4-22 Every 100 Hours...
Page 101: Every 250 Hours Or Monthly
NORAM 65ET GRADER 250 H VERY OURS OR ONTHLY Universal Joints (Drive Shaft) - Grease One fitting on the universal joint at each end of the drive shaft. 1-2 shots each. One fitting on rear end, slip joint, of drive shaft. 2-4 shots.
Page 102 NORAM 65ET GRADER Circle Turn Gearbox - Check Oil Level Position machine on a level surface. Lower moldboard to ground so draw bar is level. Remove oil check plug Oil level should be even with bottom of hole. To add oil, remove breather .
Page 103 NORAM 65ET GRADER Tire Inflation Pressure - Check DO NOT inflate tires with flammable gases or with air from systems that use alcohol injectors. An explosion with injury's could result. DO NOT stand directly in front of tire while performing maintenance. Always stand to one side and extend arm to filler valve.
Page 104: Every 500 Hours Or 3 Months
NORAM 65ET GRADER 500 H VERY OURS OR ONTHS Hydraulic Oil Filter - Change Hot fluid can burn. Fluid is under pressure. Turn cap slowly to relieve pressure before removing. Change hydraulic filter when oil is cool. 1. Loosen fill cap to release pressure.
Page 105 NORAM 65ET GRADER Hydraulic Oil Strainers - Clean Two strainers, a filler strainer and suction strainer, are used in the hydraulic system. Clean strainers when the filter element is changed and the hydraulic tank is drained. 1. Remove fill cap to release pressure 2.
Page 106 NORAM 65ET GRADER Fan Clearance - Check Engine must be “OFF”. Refer to , page "Machine Shutdown Procedure" 1. Place Master Switch in “OFF” position. NOTICE: If equipped with a CAT engine, DO NOT turn master switch OFF while lamp is illuminated.
Page 107 NORAM 65ET GRADER ROPS and FOPS - Inspect The motor grader is equipped with a Roll Over Protection System (ROPS) and Falling Object Protection System (FOPS) and a seat belt. An optional enclosed cab is available which is also ROPS and FOPS certified.
Page 108: Every 500 Hours Or 6 Months
NORAM 65ET GRADER 500 H VERY OURS OR ONTHS All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Battery - Check Battery fumes are flammable and can explode. Keep all burning materials away from battery.
Page 109 NORAM 65ET GRADER Battery Cables and Connections - Check Extinguish all smoking materials and open flames when working around batteries. Battery gas is highly flammable. Battery posts, terminals and related accessories contain lead compounds, chemicals known to the state of California to cause cancer and reproductive harm.
Page 110 NORAM 65ET GRADER Radiator Pressure Cap - Check NOTICE: An incorrect or malfunctioning cap can result in loss of coolant and the engine running hot. Ensure the correct radiator cap is being used. Inspect rubber seal of pressure cap and radiator fill neck for damage.
Page 111: Every 1000 Hours Or 6 Months
NORAM 65ET GRADER 1000 H VERY OURS OR ONTHS Transmission Oil and Filter - Change Change transmission oil and filter at the same time. 1. Support bottom transmission cover and remove bolts securing rear of cover and lower rear of cover to the ground.
Page 112 NORAM 65ET GRADER Procedure to start AEB: AEB will not start with any fault codes on display except fault “F6”. NOTE: 1. Warm up transmission. The message “Normal operating messages” is displayed. 2. Stop engine. 3. Turn on key switch.
Page 113 NORAM 65ET GRADER Display Symbol Meaning Remarks AEB - Starter button is pressed Calibrating clutch K1...K4, KV, KR K1...K4,KV,KR Wait for start, initialization of _ and Kx clutch Kx Fast fill time determination of = and Kx clutch Kx Compensating pressure...
Page 114: Every 2000 Hours Or 1 Year
NORAM 65ET GRADER 2000 H VERY OURS OR Hydraulic Oil -Change Change hydraulic oil filter and strainers whenever changing hydraulic oil. NOTE: Fluid in the hydraulic cylinders and lines is under pressure. Lower implements to ground, shut off engine and move control levers several times to relieve pressure.
Page 115 NORAM 65ET GRADER Rear Axle Housing Oil - Change Change oil in rear axle housing with oil temperature at or near normal operating temperature. 1. Remove level check plug at rear of center housing. 2. Remove drain plug and allow oil to drain. Catch drain oil in suitable container.
Page 116 NORAM 65ET GRADER Tandem Drive Case Oil - Change Change tandem case oil when oil is warm. On right side tandem case the drain plug is NOTE: at the front. On the left side the drain plug is at the rear.
Page 117 NORAM 65ET GRADER Circle Turn Gearbox Oil - Change 1. Remove drain plug from the bottom of gearbox, and drain fluid in a suitable container. Dispose of waste fluid according to federal, state, and local laws. 2. Clean area around drain plug and replace plug.
Page 118: When Required
NORAM 65ET GRADER EQUIRED Washer Fluid - Fill Fill washer fluid reservoir with clean fluid. NOTICE: DO NOT operate washer pump without fluid in the reservoir. Parking Brake - Check Check parking brake lever. It should engage between the 2nd and 3rd notch. The right console display will indicate the parking brake is engaged.
Page 119 NORAM 65ET GRADER Parking Brake Cable (Transmission End) - Adjustment 1. Support bottom transmission cover and remove bolts securing rear of cover . Lower rear of cover to the ground, allowing cover to hang from front pivot bolts. 2. Loosen jam nuts retaining cable to the bracket.
Page 120 NORAM 65ET GRADER Parking Brake Cable (Lever End) - Adjustment 1. Remove bolts and washers securing rear cover to floor. Remove rear cover. It is not necessary to remove the seat but NOTE: greater access will be gained if it is removed.
Page 121 NORAM 65ET GRADER Parking Brake Switch - Adjust / Replace The parking brake switch sends an electronic signal to the transmission that keeps the transmission from shifting into gear, or causes the transmission to shift out of gear. When the cable is replaced or adjusted at the lever end, the switch operation should be verified and adjusted, as necessary.
Page 122 NORAM 65ET GRADER Circle Guide - Adjust The circle and circle guides must be kept clean and adjusted properly. Improper adjustment will cause excessive tooth wear and poor angle control. Adjust vertical spacing before radial spacing. 1. Clean circle guides and bottom of circle so measurements are accurate.
Page 123 NORAM 65ET GRADER Moldboard Cutting Edge - Replace Cutting edges and end bits should be replaced when worn or damaged. End bits and cutting edges are interchangeable from left to right. Never work under raised equipment. Use suitable blocking to prevent moldboard from dropping.
Page 124 NORAM 65ET GRADER Battery - Charge Never make or break any of the charging circuit connections, including the connection at the batteries, when the engine is running. Never short any of the charging components to the ground. DO NOT use a booster battery or charger of more than 12 volts.
Page 125 NORAM 65ET GRADER Battery - Replace Extinguish all smoking materials and open flames when working around batteries. Battery gas is highly flammable. The 12 volt battery is "Maintenance Free" and does not require electrolyte level checks. NOTICE: Whenever working around the battery, disconnect the Master Switch.
Page 126 NORAM 65ET GRADER Battery Cables - Inspect / Replace Extinguish all smoking materials and open flames when working around batteries. Battery gas is highly flammable. Battery posts, terminals and related accessories contain lead compounds, chemicals known to the state of California to cause cancer and reproductive harm.
Page 127: Ubrication And Tier 4 Final
NORAM 65ET GRADER 5: L ECTION UBRICATION AND AINTENANCE UMMINS INAL Proper machine operation depends upon a properly maintained machine. This section provides a list of items to be checked, inspected or changed periodically. When performing maintenance, always park motor grader on level ground with the moldboard on the ground and implements pinned in place or lowered to the ground.
Page 128 NORAM 65ET GRADER Service Intervals The recommended intervals listed on the chart should be adjusted when operating in severe conditions. Time intervals should be checked when the machine reaches either the number of hours or the time allotment, whichever comes first. As an example, if the motor grader has accumulated 1200 hours and a year has passed since hydraulic oil was replaced, change the hydraulic oil now rather than waiting until 2000 hours have passed.
Page 129: Maintenance Intervals
AINTENANCE NTERVALS The maintenance intervals outlined in the following maintenance section are based on normal operating conditions. When operating under severe conditions, the maintenance intervals should be shortened. 65ET T4 FINAL SERVICE HOURS Interval Hours Identification Remarks Crankcase Breather Tube...
Page 130: Every 10 Hours Or Daily
NORAM 65ET GRADER 10 H VERY OURS OR AILY Crankcase Breather Tube - Check WEAR APPROPRIATE EYE AND FACE PROTECTION WHEN USING COMPRESED AIR. FLYING DEBRIS AND DIRT CAN CAUSE PERSONAL INJURY. Remove crankcase breather tube from engine. If crankcase breather tube contains sludge, debris, or ice, clean the tube with a strong detergent in hot water.
Page 131 NORAM 65ET GRADER Engine (Lubricating) Oil Level - Check 1. Park machine on a level surface. Allow engine oil to drain into the sump for 15 minutes after the engine has stopped before checking level. 2. Remove dipstick and check level. Oil level should be above minimum mark and below maximum mark.
Page 132 NORAM 65ET GRADER Air Filter Restriction - Check Located on the right side of the machine on the air cleaner outlet, is a filter restriction indicator . If the indicator is showing red, the outer filter is plugged and needs to be replaced. Refer to "Air Filter Outer Element -...
Page 133: Every 250 Hours Or Every 3 Months
NORAM 65ET GRADER 250 H VERY OURS OR VERY ONTHS All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Charge-Air Piping - Check Inspect the charge-air piping...
Page 134: Every 500 Hours Or Every 6 Months
NORAM 65ET GRADER 500 H VERY OURS OR VERY ONTHS All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Fuel Filters - Change Refer to the Engine Operation and Maintenance Manual supplied with machine for additional information.
Page 135 NORAM 65ET GRADER Engine (Lubricating) Oil and Filters - Change 1. Change oil filter when the engine oil is changed. The o-ring can stick on the filter head. Make NOTE: sure it is removed before installing the new filter. 2. Remove plug on bottom of the engine oil pan and drain oil into a suitable container.
Page 136 NORAM 65ET GRADER Engine Coolant Antifreeze - Check NOTICE: Over-concentration of antifreeze or use of high silicate antifreeze can cause engine damage. Check the antifreeze concentration. Use a mixture of 50% water and 50% ethylene glycol or propylene glycol-base antifreeze to protect the engine to -25°F (-32°C) year-around.
Page 137: Every 1000 Hours Or 1 Year
NORAM 65ET GRADER 1000 H VERY OURS OR Radiator Pressure Cap - Check The cooling system is designed to use a pressure cap prevent the coolant from boiling. An incorrect or malfunctioning cap can result in the loss of coolant and the engine running hot.
Page 138: Every 2000 Hours Or 2 Years
NORAM 65ET GRADER 2000 H VERY OURS OR EARS Engine Coolant - Change Change engine coolant when engine temperature is cold. Hot fluid under pressure can scald. Allow engine to cool before opening radiator cap. Coolant should be kept off skin. Follow precautions outlined on anti-freeze container.
Page 139: When Required
NORAM 65ET GRADER EQUIRED Air Filter Outer Element - Replace An indicator mounted on the air cleaner cover will turn red when the outer air filter element requires replacement. Remove air cleaner end cover 2. Carefully remove outer element taking care not to disturb the inner element or knock any dirt off the outer element.
Page 140 NORAM 65ET GRADER Air Cleaner Secondary Element - Replace Change air filter inner element every third time the outer element is changed. NOTICE: DO NOT clean inner element. 1. Remove air filter outer element and replace, as necessary. Refer to "Air Filter Outer Element -...
Page 141 NORAM 65ET GRADER Fuses - Replace If an electrical circuit does not work, check the fuse panel under the right side console and/or the fuse panel inside the right engine compartment. Fuses may have blown, breaking the circuit. Be sure to locate the cause of the blown fuse before replacing.
Page 142 This page intentionally left blank.
Page 143: Ubrication And Cat Tier
NORAM 65ET GRADER 6: L ECTION UBRICATION AND AINTENANCE CAT T INAL Proper machine operation depends upon a properly maintained machine. This section provides a list of items to be checked, inspected or changed periodically. When performing maintenance, always park motor grader on level ground with the moldboard on the ground and implements pinned in place or lowered to the ground.
Page 144 NORAM 65ET GRADER Service Intervals The recommended intervals listed on the chart should be adjusted when operating in severe conditions. Time intervals should be checked when the machine reaches either the number of hours or the time allotment, whichever comes first. As an example, if the motor grader has accumulated 1200 hours and a year has passed since hydraulic oil was replaced, change the hydraulic oil now rather than waiting until 2000 hours have passed.
Page 145: Maintenance Intervals
AINTENANCE NTERVALS The maintenance intervals outlined in the following maintenance section are based on normal operating conditions. When operating under severe conditions, the maintenance intervals should be shortened. 65ET T4 FINAL SERVICE HOURS Interval Hours Identification Remarks Engine Coolant Level...
Page 146: Every 10 Hours Or Daily
NORAM 65ET GRADER 10 H VERY OURS OR AILY Refer to the Engine Operation and Maintenance Manual supplied with the machine for engine maintenance information. Engine Coolant Level - Check Hot fluid under pressure can scald. Allow engine to cool before opening radiator cap.
Page 147 NORAM 65ET GRADER Engine Air Precleaner - Check / Clean 1. Remove cover 2. Check for an accumulation of dirt and debris in body 3. Clean body. 4. Install cover and wing nut. When the engine is operated in dusty NOTE: applications, more frequent cleaning is required.
Page 148 NORAM 65ET GRADER Fuel System Primary Filter / Water Separator - Drain Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Page 149: Every 50 Hours Or Weekly
NORAM 65ET GRADER 50 H VERY OURS OR EEKLY All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Hoses and Clamps - Inspect / Replace Contact with high pressure fuel may cause fluid penetration and burn hazards.
Page 150 NORAM 65ET GRADER Fuel Tank Water and Sediment - Drain Fuel quality is critical to the performance and to the service life of the engine. Water in the fuel can cause excessive wear to the fuel system. Condensation occurs during the heating and cooling of fuel.
Page 151: Every 250 Hours
NORAM 65ET GRADER 250 H VERY OURS All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Engine Oil Sample - Obtain Refer to the Engine Operation and Maintenance Manual supplied with the machine for instructions.
Page 152: Every 500 Hours Or 1 Year
NORAM 65ET GRADER 500 H VERY OURS OR All maintenance checks and inspections listed in previous maintenance intervals must be performed at this time in addition to those listed under this maintenance interval. Engine Air Cleaner Primary Element - Clean / Replace NOTICE: Never run engine without an air cleaner element installed.
Page 153 NORAM 65ET GRADER 1. Remove the cover 2. Carefully remove the primary element taking care not to disturb the inner element or knock any dirt off the outer element. 3. Cover the air inlet with tape to keep dirt out.
Page 154 NORAM 65ET GRADER Cleaning Primary Air Cleaner Element NOTICE: The primary air cleaner element can be used up to six times if the element is properly cleaned and properly inspected. Replace the primary element at least once a year, regardless of number of cleanings.
Page 155 NORAM 65ET GRADER Engine Air Cleaner Secondary Element - Inspect / Replace Change air filter inner element every third time the outer element is cleaned. NOTICE: DO NOT clean the inner element. The secondary air cleaner element is not serviceable.
Page 156 NORAM 65ET GRADER Engine Oil and Filter - Change Hot oil and hot components can cause personal injury. DO NOT allow hot oil or hot components to contact skin. NOTICE: Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
Page 157 NORAM 65ET GRADER Fuel Filters - Change Refer to Engine Operation and Maintenance Manual supplied with machine for instructions. Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the ignition switch off when changing fuel filters or water separator elements.
Page 158 NORAM 65ET GRADER To Prime the System: 1. Pump the primer on filter head until the primer stiffens and it is difficult to pump, approximately 80 pumps. Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Page 159 NORAM 65ET GRADER Radiator - Clean Personal injury can result from air pressure. Personal injury can result without following proper procedure. When using pressure air, wear a protective face shield and protective clothing. Maximum air pressure at the nozzle must be less than 30 psi (205 kPa) for cleaning purposes.
Page 160: Every 1000 Hours
NORAM 65ET GRADER 1000 H VERY OURS Water Pump - Inspect Visually inspect water pump for leaks. Refer to “CAT C3.4B Industrial Engine Operation and Maintenance Manual” for complete instructions. 1500 H VERY OURS Engine Crankcase Breather Element - Replace Refer to “CAT C3.4B Industrial Engine Operation and Maintenance Manual”...
Page 161: Every 2000 Hours
NORAM 65ET GRADER 2000 H VERY OURS Aftercooler Core - Inspect Inspect aftercooler for these items: damaged fins, corrosion, dirt, grease, insects, leaves, oil, and other debris. If necessary, clean the after cooler core. Refer to “CAT C3.4B Industrial Engine Operation and Maintenance Manual” for complete instructions.
Page 162: When Required
NORAM 65ET GRADER EQUIRED DEF Filler Screen - Clean Refer to “CAT C3.4B Industrial Engine Operation and Maintenance Manual” for complete instructions. DEF Tank - Flush Refer to “CAT C3.4B Industrial Engine Operation and Maintenance Manual” for complete instructions. Engine - Clean When using a steam cleaner, wear safety glasses or a face shield and protective clothing.
Page 163 NORAM 65ET GRADER Fuses - Replace If an electrical circuit does not work, check the fuse panel under the right side console and/or the fuse panel inside the right engine compartment. Fuses may have blown, breaking the circuit. Be sure to locate the cause of the blown fuse before replacing.
Page 164 This page intentionally left blank.
Page 165 NORAM 65ET GRADER 7: S ECTION PECIFICATIONS 65ET CUMMINS Tier 4 Final Engine Model ............Cummins QSF3.8 Tier 4 Type .
Page 166 NORAM 65ET GRADER 65ET CAT Tier 4 Final Engine Model............. . CAT C3.4B Tier 4 Type.
Page 167 NORAM 65ET GRADER Torque Converter Make and Model ..........ZF Model F&S W300 Type .
Page 168 NORAM 65ET GRADER Transmission Ratios and Theoretical Travel Speeds Forward Reverse Ratio Km / hr Ratio Km / hr 5.202 4.939 3.367 2.078 10.9 2.191 10.9 1.418 10.3 16.6 0.944 15.8 25.4 0.611 24.0 38.6 Steering Control Unit Make and Model... . Eaton Fluid Power Series 5 Load Sense Steering Valve Type.
Page 169 NORAM 65ET GRADER Articulation Type ..........Hydraulic with Upper and Lower Joints Upper Bearing .
Page 170 NORAM 65ET GRADER Fluid Capacities Fuel Tank ............. . 121 L (32 gal) Cooling System .
Page 171 NORAM 65ET GRADER Power Brakes Type ....... . Self-Adjusting, Wet Multi-Disc Integral with Rear Axle Disc Size.
Page 172 NORAM 65ET GRADER Tandem Drive Construction ........1/2 in Steel Plate Rectangular Section Drive .
Page 173 NORAM 65ET GRADER Rear Axle Construction ........... . .Heavy Duty Cast Iron Mounting .
Page 174 NORAM 65ET GRADER Hydraulic Control Valve Make and Model ........... . . Husco 5000 Series Type.
Page 175 NORAM 65ET GRADER Circle Construction ....... Welded T-Section with Integral Teeth Segments Top Gear Size .
Page 176 NORAM 65ET GRADER Moldboard Type 1 ........”Roll Away” Involute Curve with Replaceable Cutting Edges and Bits Actuation .
Page 177 NORAM 65ET GRADER Moldboard Reach (10 ft Moldboard) Reach Outside Rear Wheels w/ Straight Frame Left ..............39.1 in (994 mm) Right.
Page 178 NORAM 65ET GRADER Operation Weights Machine Operating Weight w/ Scarifier and Cab......17000 lb (7711 kg) Front Axle .
Page 179 NORAM 65ET GRADER PTIONS Scarifier Attachments ..............Front Linkage .
Page 180 NORAM 65ET GRADER Ripper Attachment ..............Rear Linkage .
Page 181 NORAM 65ET GRADER Features include Cloth Air Suspension Seat, Floor mats, Heater/Pressurizer, Tiltable Windshield, Sliding Rear Window, Two-Lockable Full-Size Doors, Coat Hook, Lunch box Location, Dome Light, Front and Rear Windshield Wipers and Washers, Inside Mirror, Head Liner, and optional Air Conditioner.
Page 182 NORAM 65ET GRADER 7-18 Options...
Page 183 NORAM 65ET GRADER 7-19 Options...
Page 184 This page intentionally left blank.
Page 185 NORAM 65ET GRADER 8: T ECTION ROUBLESHOOTING NOTICE: This section is provided as an aid for troubleshooting the motor grader. It is not intended to replace a qualified mechanic. If repairs are required beyond routine maintenance, the machine should be returned to the dealer who has the correct tools, facilities, and knowledge to perform repairs correctly and safely.
Page 186 NORAM 65ET GRADER YDRAULICS AND MPLEMENTS PROBLEM POSSIBLE CAUSE CORRECTION Contact an authorized dealer Pump worn All Hydraulic Low oil level Add oil Functions fail to Faulty system relief valve Contact an authorized dealer operate Restricted pump suction line Clean suction strainer...
Page 187 NORAM 65ET GRADER INDEX Engine Oil Sample - Obtain 6–9 Fan Clearance - Check 6–9 A/C Switch - (Cab Equipped) 2–26 Fuel Filters - Change 6–15 Accelerator Control Pedal 2–27 Fuel System - Prime 6–20 Active Engine Error Screen 2–38 Fuel System Primary Filter / Water Active Error Screen 2–38...
Page 188 NORAM 65ET GRADER Cummins Accessing Lubrication and Electronic Display 2–28 Check Points 5–2 Active Engine Error Screen 2–38 Air Filter Outer Element - Replace 5–13 Active Error Screen 2–38 Air Filter Restriction - Check 5–6 AEB Calibration Screen 2–35 Air Intake Piping - Check 5–6 Electronic Display Navigation 2–39...
Page 189 NORAM 65ET GRADER Maintenance 10 Hours or Daily 4–12 General Information 4–4 50 Hours or Weekly 4–17 General Safety Messages 1–4 100 Hours 4–21 Grader Components 250 Hours or Monthly 4–23 Accessing Lubrication and 500 Hours or 3 Months 4–26 Check Points 4–6...
Page 190 NORAM 65ET GRADER Front Wheel Lean Control - Standard Style Configuration 2–22 Hazard Lights Switch 2–18 Implement Control Headlights 2–20 - Caterpillar Style Configuration 2–24 Heating (Cab Equipped) 2–14 Implement Control Heating (Cab-Equipped Models) 2–14 - Standard Style Configuration 2–21 Horn 2–20...
Page 191 NORAM 65ET GRADER Safety Decal Locations 1–6 Safety Decals - Inspect 1–5 Operating Engine Safety Messages 1–1, 4–1 Machine Shutdown Procedure 3–6 Safety Symbol Explanation 1–2 Machine Starting Procedure 3–4 Seat 2–15 Preparing to Start Engine 3–4 Seat Adjustments 2–15 Starting Engine 3–5...
Page 192 NORAM 65ET GRADER Start-Up Screen 2–28 Steering Taillights 2–20 Front Wheel Lean 3–9 Throttle Control Lever 2–25 Storage Box 2–27 Transmission 3–19 Switch Changing Direction 3–20 A/C - (Cab Equipped) 2–26 Engaging 3–19 Blower Fan (Cab Equipped) 2–26 Inching Control 3–20 Cab Dome Light 2–27...
Page 193 NORAM 65ET GRADER EVISION ISTORY Revision Date Pages Description 65E T4 First Edition Tier 4 Final Operation and October 2015 10/2015 Maintenance Manual Released. 34491...
Page 194 NORAM 65ET GRADER CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. When operated in California, any off-road diesel vehicle may be subject to the California Air Resources Board In-Use Off-Road Diesel Vehicle Regulation.

NorAM 65ET T4 FINAL Operator's Manual

Quick Links

Related Manuals for NorAM 65ET T4 FINAL

Summary of Contents for NorAM 65ET T4 FINAL

Table of Contents