Summary of Contents for Qlight QTG L-WIZ Series
- Page 1 Wireless Network System User Manual WIZ32 -USB DONGLE : GW768 -Gateway QTGxxL-WIZ, QMCLxxx-WIZ -ROUTER QLIGHT November 4 2019...
- Page 2 Index a. Rule Part 15.19(a)(3): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 3 Wireless Network System User Manual 1. What is Wireless Network System(WNS)? Wireless Network System (WNS) is the system to allow a user to monitor or control the operation data or system of the equipment with PC, a smartphone, or a tablet device by receiving information about various production equipment wirelessly.
- Page 4 Wireless Network System User Manual 2. Components Application software A Wireless Signal Information Device 1) Description Item Description PC Application would be a comprehensive control system by enabling the setting, monitoring, control and log analysis of the wireless signal information PC Application and device.
- Page 5 Wireless Network System User Manual 3. Wireless Network System Configuration 1) WNS It converts the signals of the external contact point sent from production equipment into wireless signals in order to monitor the status information of production equipment any time and anywhere with PC, tablet PC, and smartphone.
- Page 6 Wireless Network System User Manual 3) Connection through USB Dongle - USB dongle can be easily inserted in the PC and this is a method suitable for building a small-sized single wireless network (up to 32 wireless control display lamps can be connected).
- Page 7 Wireless Network System User Manual 5. Terminology and Description 1) Frequency Band WNS uses 2.4GHz wireless frequency band in compliance with IEEE802.15.4(ZigBee) and has a total of 16 frequency channels. Transmission (sending/receiving) time can be delayed if there is wireless LAN (Wi-Fi) around. WLAN (Wireless LAN) uses 2.4GHz (IEEE802.11) and thus may overlap with 2.4GHz (IEEE802.15.4).
- Page 8 Wireless Network System User Manual - Please refer to below table for each channel’s frequency information of wireless system and wireless LAN. - Please select the channel by referring below table when installing the wireless products. Frequency Bandwidth Frequency Interval Ch.
- Page 9 Wireless Network System User Manual 2) Pan ID (Personal Area Network) The Pan ID is the basic unit of wireless communication, used when grouping is necessary. However, it is used to assign a separate ID to each client in the environment of WNS for signal information devices. When a client’s devices, which should be distinguished from those of other companies around or in the same workplace, a different ID is assigned to each client.
- Page 10 Wireless Network System User Manual 3) MAC Address When it is necessary to divide wireless signal information devices into groups in WLAN, Gateway should be used. Gateways can exchange information with one another in Ethernet communication through a wire router. For Ethernet communication, each device connected to the gateways should be assigned with a unique MAC address.
- Page 11 Wireless Network System User Manual 4) What is Mast Gateway? When configuring a system using multiple gateways in a wireless network system, a specific gateway should be designated as a mast gateway. Each gateway is directly connected to a host PC to transmit information but it is by the mast gateway that transmits information to a mobile device.
- Page 12 Wireless Network System User Manual 5. Installation environment 1) Wireless Network System installation Nominal wireless signal transmission distance of Wireless Network System is 100m. However actual transmission distance would be 30 to 50m due to interference of other 2.4G bandwidth equipment and building.
- Page 13 Wireless Network System User Manual 4) Wireless Network System installation The wireless signaling device supports Mesh Topology. Multi-hop feature allows relay between the devices depending on communication distance. Although it is possible to transfer the value of a device remotely by using the relay feature, it is not recommended to transfer multiple devices’ signals via single device as shown in the example below.
- Page 14 Wireless Network System User Manual Good example of relay) 장애물 : Obstacle If it is inevitable to install behind of obstacle like #7, device #6 shall be as a repeater. Please take care of device #6 that does not control more than 2 wireless signaling devices.
- Page 15 Wireless Network System User Manual 6. Product Specifications 1) PC Application - It is the basic PC program needed to operate and manage WNS. - It can be downloaded from the homepage of Qlight Co. Operating Program Item Description - Processor: 1GHz or higher...
- Page 16 - The status information of a wireless signal information device can be monitored or controlled by a mobi le application. - The mobile application is used to interlock with the gateway. The application can be downloaded from our website, www.qlight.com or Goggle App Store. Mobile APP Item...
-
Page 17: Usb Dongle
Wireless Network System User Manual 3) USB DONGLE • Easy installation and operation by plugging it to a PC, controls and monitors up to 32 wireless devices. • Suitable for a single or small-scaled wireless network connection needs. (1) Specifications Article Description Model name... - Page 18 Wireless Network System User Manual (2) Ordering Specification (3) Technical Diagram...
- Page 19 Wireless Network System User Manual 4) Gateway - Suitable for large-scaled network over 32 wireless networks. One gateway unit is a single group, can connect up to 24 groups. - Support Smartphone Application Gateway AC Adaptor (AC model is optionally available) Ethernet cable USB cable (1) Specifications...
-
Page 20: Technical Diagram
Wireless Network System User Manual Weight 0.22Kg -USB to Serial -1 PC per single connection Wired communication -Ethernet (Conforms to the IEEE 802.3) protocol 10BASE-T / 100BASE-TX -One gateway unit can connect up to 24 groups Wireless communication IEEE 802.15.4 protocol Data rate 250Kbps... - Page 21 Wireless Network System User Manual (4) Feature Description Remark Power LED(RED) Wireless Signal Receiving indicator LED(GREEN) Wireless Signal Transmission indicator LED(BLUE) Error & Boot LED(AMBER) Power ON/OFF Switch Power Connector(AC) Power Connector(DC) USB Cable Connector Ethernet Cable Connector...
- Page 22 Wireless Network System User Manual 5) ROUTER(Wireless Signaling Device) -The status information of the production equipment can be recognized by using an external contact and the status information is transmitted to USB DONGLE or GATEWAY. -Router can receive control signal from USB DONGLE or GATEWAY. Wireless Signaling Device (1) Specifications Article...
- Page 23 Wireless Network System User Manual Flashing signal T of H1, L1, H2 : 300ms ≤T > 600ms recognition H1, L1, H2 signals are recognized as Flashing signal in ‘t’ time range when the signal input sequence is from H1, L1, to H2. When it recognized as Flashing mode, it transfers Flashing signal wirelessly.
- Page 24 Wireless Network System User Manual (2) Ordering Specification - Wireless Signaling Devices(QTG/QTC/QTR60L Series) - - Wireless Signaling Devices(QTG/QTC/QTR70L Series) - - Wireless Signaling Devices(QMCL Series)
- Page 25 Wireless Network System User Manual (3) Technical Diagram...
- Page 26 Wireless Network System User Manual 7. Installation This WNS uses wireless communication of 2.4GHz frequency band. Check if your environment is suitable for wireless communication before installing it. 1) USB Dongle Just insert the USB dongle into one of the PC USB ports and installation completes. - This way is suitable for building a small-sized single wireless network.
-
Page 27: Lan Router
Wireless Network System User Manual (1) Gateway Connection with USB Used the enclosed USB cable to connect between the PC and the gateway. (2) Gateway Connection with Ethernet Use the LAN router to connect the PC and the gateway. Use the enclosed cable. It doesn't matter whether it is cross or direct cable. - Use DC power or enclosed AC adaptor to turn on the gateway. - Page 28 Wireless Network System User Manual 3) Wiring Instructions...
- Page 29 Wireless Network System User Manual...
- Page 30 Wireless Network System User Manual...
- Page 31 One is using USB dongle and the other one is gateway’s USB interface. In both cases, 'USB to serial device driver' should be installed(download it from Qlight website). - Select x64 or x86 .EXE file depending on your PC operating system.
- Page 32 Wireless Network System User Manual 8. Operation There are two ways of receiving or controlling the status information of a wireless signal information device: through i) USB dongle and (ii) USB interface with the gateway. In both cases, ''USB to serial device driver' should be installed (provided separately.) - File name: CP210xVCPInstaller_x64 After installing the PC program, you can set wireless devices such as gateways, USB dongle, and...
-
Page 33: View Area
Wireless Network System User Manual 2) Main Screen of PC Application When Qlight Manager is installed, the screen below is displayed. Please read the name and the descri ptions of the function of each item. ① Menu 1 Menu 2 Menu 3 ②... -
Page 34: Description Of Menu
Wireless Network System User Manual (2) Description of Menu 2 ⑦ ⑧ ⑨ ⑩ Item Description The function to alert a manager when an alarm goes off in the wireless signal ⑦ Router Alarm ON information device, even with the PC Application in the background mode. It scans the wireless signal information devices connected to the USB dongle ⑧... - Page 35 Wireless Network System User Manual 3) Setting (1) USB Dongle ② ① ④ ⑥ ③ ⑤ ①: Select USB DONGLE -> USB Interface in the setting menu. ②: Select the COM# Port in the drop-down list and press the Connect button to connect with the USB dongle.
- Page 36 Wireless Network System User Manual (2) Gateway - The Setting of USB Interface with Gateway The GW768 device is connected with a PC through the USB Interface and can communicate with the wireless signal information devices. Furthermore, it is also possible to set the GW786 network using the USB Interface.
- Page 37 Wireless Network System User Manual Field Description Range Less than 20 Name Gateway name and details alphabets Group ID Control group ID 0 to 65535 Channel Wireless channel frequency 11 to 26 Panid Network ID 0 – 65535 The output value of the wireless transmission, the higher the Txpower setting the stronger the power -31 to 10...
- Page 38 Wireless Network System User Manual (2) Gateway - The Setting of LAN Interface of Gateway ① ④ ⑥ ③ ⑤ ①: Select GATEWAY -> LAN Interface in the setting menu. ②: Select the MAC Address in the drop-down list and press the Connect button to connect with the ga teway.
- Page 39 Wireless Network System User Manual Field Description Range Less than 20 Name Gateway name and details alphabets Group ID Control group ID 0 to 65535 Channel Wireless channel frequency 11 to 26 Panid Network ID 0 to 65535 The output value of the wireless transmission, the higher the Txpower setting the stronger the power -31 to 10...
- Page 40 Wireless Network System User Manual (3) Router - The Setting of USB Interface with Router ② ① ④ ⑥ ③ ⑤ ①: Select ROUTER -> USB Interface in the setting menu. ②: Select the COM# Port in the drop-down list and press the Connect button to connect with the route r(s).
- Page 41 Wireless Network System User Manual Field Description Range Sound Type Select the sound output mode for the router. Speaker/Buzzer When the speaker is selected as the sound type, select the Sound Source WS/WP/WM/WA/WV sound tone (color). Select the number of LED colors for the wireless signal Lamp Layer information devices.
- Page 42 Wireless Network System User Manual (4) Setting of Mobile Device and Master IP Address ③ ① ⑤ ② ④ ①: Select MOBILE -> SETTING in the setting menu. ②: Press the Read button to retrieve the initial settings of the manufacturer. ③: Confirm the status values of the retrieved field or modify them to suit a client's use environment.
- Page 43 Wireless Network System User Manual Field Description Range It sets the ID to be used in accessing a mobile application. Password It sets the password to be used in accessing a mobile applic ation. Mobile Alarm Even with the mobile application on the background, it activates a push alarm message when a signal occurs in the wireless signal information device.
- Page 44 Wireless Network System User Manual 4) Connections ① ② ③ VIEW AREA Item Description USB DONGLE When the wireless network system is connected through the USB dongle, select ① USB Conn. and use this menu. GATEWAY When the wireless network system is connected through the gateway USB, sele ②...
- Page 45 Wireless Network System User Manual (1) Use of USB Dongle ① ② ③ ①: Select Connection -> USB DONGLE -> USB Conn. ②: Select the COM# Port in the drop-down list. ③: Press the Connect button to connect with the USB dongle. ⑤...
- Page 46 Wireless Network System User Manual - How to Control a Wireless Signal Information Device ① ③ ④ ⑤ ② ①: Check the box of USB GROUP21 and the entire wireless signal information devices in ② will be selected or cleared. ②: Each router can be selected or cleared by checking individual boxes.
- Page 47 Wireless Network System User Manual - How to Change Router Settings ① ② ③ ①: It is possible to change the settings of a signal information device wirelessly. Place a mouse on the wireless signal information device whose settings are to be changed and click on the right mouse button.
- Page 48 Wireless Network System User Manual Field Description Range It can set the node ID of a wireless signal information device. The setting range of the node ID is wide but a group can use Node ID overlapped node ID. 0 to 65535 One group can connect up to 32 routers and thus most of the groups use node ID between 01 and 32.
- Page 49 Wireless Network System User Manual (2) Use of Gateway - With USB ① ② ③ ①: Select Connection -> GATEWAY -> USB Conn. ②: Select the COM# Port in the drop-down list. ③: Press the Connect button and connect with the gateway. ⑤...
- Page 50 Wireless Network System User Manual - How to Control a Wireless Signal Information Device ③ ① ④ ② ⑤ ①: Check the boxes of GATEWAY GROUP24 and the entire wireless signal information devices in ② will be selected or cleared. ②: Each router can be selected or cleared by checking individual boxes.
- Page 51 Wireless Network System User Manual (2) Use of Gateway - With LAN ① ② ③ ①: Select Connection -> GATEWAY -> LAN Conn. ②: Select the COM# Port in the drop-down list. ③: Press the Connect button and connect with the gateway. ⑤...
- Page 52 Wireless Network System User Manual - How to Control a Wireless Signal Information Device ③ ① ④ ② ⑤ ①: Check the boxes of GATEWAY GROUP24 and the entire wireless signal information devices in ② will be selected or cleared. ②: Each router can be selected or cleared by checking individual boxes.
- Page 53 The mobile application is used to monitor, set, and control the status information of a wireless signal information device with a mobile device. Download the installation file of the mobile application (QlightRFMobile_Vx.x.x) from Qlight website and install it. When installation is completed, Qlight RFManager application appears. Before run the mobile...
- Page 54 Port Number information about the mobile device. ③ Mobile ID Enter the mobile ID set in the Qlight Manager. ④ Password Enter the password set in the Qlight Manager. After entering all of ① to ④ items, click the Connect button and the mobile ⑤...
- Page 55 Wireless Network System User Manual (3) Use of Mobile Application When the mobile application logs in, all the gateways connected to it are displayed. Click each of them and it will display the routers in the group. (Unlike the PC Application, the routers are not controlled by group in the mobile application. They are controlled individually.) ①...
- Page 56 Wireless Network System User Manual (3) Use of Mobile Application ① ② ①: After selecting how to control the LED of the selected routers, press the Send button to control the selected routers. ②: Move the slide button of the Sound Control of the selected router to right or left to control the sound play of the selected router.
- Page 57 Wireless Network System User Manual 6) Router Alarm Check the boxes (MOBILE SETTING -> Alarm information) in the setting menu and alarm logs are dis played in the PC Application or the mobile application and the operation status of the routers is indicat ed, depending on the operation of the router.
- Page 58 Wireless Network System User Manual - Router Alarm in Mobile Application When a router is controlled by the external contact point, except for the mobile application, or in the PC Application, the mobile application displays a router alarm. ① ② ①: It displays the mode ID and group ID of the selected router.
- Page 59 ⑥ ①: Designate the saving path for log files using 'Log save location' in the Log menu. - The default path is C:\Qlight\Logs. ②: It can select to view log files by group or product as a whole. ③: It can select log files on a daily, weekly, monthly, or yearly basis.
- Page 60 - Software version: the firmware version of a wireless signal information device. - Playing sound number: channel number - Sound type: The WS/WP sound tone (color) of Qlight's sound sources (see the basic sound tones (colors) in the Qlight's homepage.) - Sound source: speaker type or buzzer type.
- Page 61 Wireless Network System User Manual 8) Manual Manual part provides a brief description of the PC operation program so that the user can use the PC application easily. Brief manuals for Quick Manual, Connection, Setting, LED and Sound control. 1. Menu Connection : Configure USB dongle and Gateway connection Setting : Configure USB dongle and Gateway...
- Page 62 Wireless Network System User Manual 9) Use of Configuration Menu ① ② ③ ①: Use the Network button in the Config menu to set wireless transmission (sending/receiving). ②: It is a wireless setting used when sending the packets of the gateways or the USB dongle to the wireless signal information device.
- Page 63 Wireless Network System User Manual Item Description It is the interval (time) at which the status of a wireless signal information d evice is checked. When it is set to 5, it is checked every 5 seconds. Duty cycle Time indicates how long it takes to check one wireless signal information d evice.
-
Page 64: Usb Dongle
Wireless Network System User Manual 9. Layout and detailed information 1) Dimensional Drawing USB DONGLE GATEWAY ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨... - Page 65 Wireless Network System User Manual GATEWAY Descriptions Remark ① Power Status Indicator LED (Red) ② Communication Status Indicator LED (Green) ③ Communication Status Indicator LED (Blue) ④ Error Indicator LED (Yellow) ⑤ Power ON/OFF Switch ⑥ Power input port (AC) ⑦...
- Page 66 Wireless Network System User Manual 2)USB Dongle 3)Gateway Gateway USB Cable Ethernet AC power Cable adaptor (Optional)
- Page 67 Wireless Network System User Manual 4) Signal Tower Light Cover(ABS) Lens(PC) Router 라우터 Buzzer volume Control Lever Pipe(AL)
- Page 68 Wireless Network System User Manual 3. Ordering Specification 1)USB DONGLE WIZ32 [Model Number] WIZ32 2)GATEWAY 12/24 GW768 [Model Number] [Voltage] GW768 12/24 -DC12V to 24V 110/220 -AC110V to 220V 3) Wireless LED Signal Lights(QCML Series) [Model Number] [Buzzer Option] [Voltage] •...
- Page 69 Wireless Network System User Manual 4) Wireless LED Tower Lights(QTG/QTC/QTR60L Series) 5) Wireless LED Tower Lights(QTG/QTC/QTR70L Series)