Advertisement
DO NOT use in bad weather conditions, especially when there is a risk of lightning. DO NOT expose to rain. Only use in good light.
8
DO NOT use if tool vibrates abnormally, switch off, remove battery and then inspect.
8
DO NOT touch hazardous moving parts. Allow to come to a complete stop first.
8
DO NOT operate whilst tired, ill under the influence of alcohol or other intoxicating drugs.
8
DO NOT overreach and keep balance at all times.
8
DO NOT use if damaged. DO NOT operate with defective guards or shields or without safety devices.
8
DO NOT use for a task it was not designed to perform.
8
Store with the battery removed and separate from the machine, in a dry, childproof location.
9
WARNING! Never allow children, persons with reduced physical sensory or mental capabilities or lack of experience and knowledge
‰
or people unfamiliar with these instructions to use the machine, local regulations may restrict the age of the operator.
WARNING! DO NOT touch moving hazardous parts before the machine is disconnected from the battery and the moving hazardous
‰
parts have come to a complete stop.
Keep all parts of the body away from the gardening tools. DO NOT remove cut material or hold material to be cut when blades are
9
moving. Blades continue to move after the switch is turned off.
Carry the tool by the handle with the attachments stopped and taking care not to operate any power switch. Proper carrying of the tool
9
will decrease the risk of inadvertent starting and resultant personal injury from the gardening tools.
When transporting or storing the tool, always fit the blade cover. Proper handling of the tool will decrease the risk of personal injury
9
from the blades.
WARNING! Check the area to be worked for foreign objects e.g. wire fences
‰
2. INTRODUCTION
Cordless 3 in 1 garden tool – body only, is designed to make trimming and gardening quick and easy. Its ergonomic design and lock-in
function make it comfortable and easy to use. There are 3 tool-less interchangeable functions which means you can select the grass shearing
blade, the hedge trimmer blade for light trimming or the raker. Requires compatible 20V battery and mains charger, sold separately.
3. SPECIFICATION
Model No ............................................................. CP20VGT3
Battery ................... 20V 2Ah - 6Ah Lithium-ion (not included)
4. OPERATION
WARNING: Remove battery before fitting / removing parts or
‰
maintenance is carried out.
WARNING: Wear appropriate hand protection when fitting or
‰
removing parts or maintenance is carried out.
NOTE: When new, the batteries may have been shipped in a
low charge state. Fully charge the batteries before using your tool.
4.1.
Ensure that you have read, understood and comply with all the
safety instructions in Section 1.
4.2.
INSTALLING / REMOVING SHEARS
fig.1
4.2.1.
Set the tool on it's back to expose the plastic cover (fig.1). Depress the tab and slide the cover forwards and away from the tool.
4.2.2.
Removing the Shears: Lift shears cutting blades upwards and forwards to lift them off of the two pins and out of the body.
4.2.3.
Installing the shears: With the shear blade drive mechanism facing downwards into the body, hold the shears at a slight angle and
slide the mechanism into the body, locating the rectangular cut-outs in the mechanism into the corresponding lugs in the
body (fig.3). Manipulate the mechanism such that the two holes in it line up with the pins in the body.
4.2.4.
Press the shears firmly down to engage the drive mechanism.
4.2.5.
Replace the plastic cover.
4.3.
INSTALLING / REMOVING TRIMMER
4.3.1.
Follow steps 4.2.1 to 4.2.5 above.
4.4.
INSTALLING / REMOVING RAKE
4.4.1.
Follow steps 4.2.1 to 4.2.5 above.
4.5.
OPERATION
4.5.1.
To release and operate the trigger, slide the security lock forward (fig.4).
4.5.2.
To stop the machine, release the trigger and allow the security lock
to slide back.
5. MAINTENANCE
WARNING: Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
‰
5.1.
GENERAL INSPECTION
5.1.1.
Regularly check that all the fixings are tight.
5.1.2.
Repairs should be carried out by an authorised service centre.
© Jack Sealey Limited
Noise power/pressure .......................................... 86/73dB(A)
Vibration/Uncertainty .......................................... 3.82/1.5m/s²
fig.2
Original Language Version
fig.3
Location lugs
Security
Lock
fig.4
CP20VGT3 Issue 1 19/01/22
Trigger
Advertisement
