Summary of Contents for Gamma DIGITEL MPCq
- Page 1 DIGITEL MPCq CONTROLLER USERS MANUAL Document 900034, Rev B ISO 9001:2015 Certified...
-
Page 2: Table Of Contents
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B CONTENT 1. GENERAL INFORMATION ..........3 2. APPROVALS ................ 3 3. WARNINGS................ 3 4. UNPACKING THE CONTROLLER ........4 5. SAFETY NOTICES ............... 4 6. INSTALLATION ..............4 7. CONTROLLER CONFIGURATION ........5 8. -
Page 3: General Information
Document 900034, Rev B 1. GENERAL INFORMATION 2. APPROVALS The DIGITEL MPCq is shown to meet the intent of Directive 89/336/ The DIGITEL™ MPCq is an ion pump power supply controller. EEC for Electromagnetic Compatibility and Low Voltage Directive It is designed to operate up to two independent ion pumps along 73/23/EEC for product Safety. -
Page 4: Unpacking The Controller
Document 900034, Rev B 4. UNPACKING THE CONTROLLER 6. INSTALLATION The DIGITEL MPCq is a full 19 inch rack controller. No additoinal 4.1 Inspect For Any Obvious Damage hardware needed to install in a standard 19 inch wide device rack. -
Page 5: Controller Configuration
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 7. CONTROLLER CONFIGURATION 8. HV CONTROL / ION PUMP OPERATION Following configuration options are specified at order time: 8.1 Prior to using an ion pump Confirm following: 7.1 Input Mains AC Voltage (110Vac vs. 220Vac) - Rough pump down to 1x10 Torr or less (the lower the better). -
Page 6: Pressure Measurement
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 9. PRESSURE MEASUREMENT Pressure value is determined using following equation Where: I - Current in amps. V - Voltage in volts. U - Pressure units conversion factor (1 for Torr, 1.33 for mBar and 133 for Pascal). -
Page 7: Touchscreen User Interface
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11. TOUCHSCREEN USER INTERFACE 11.2 Main Menu (Page 1) 11.1 Home Screen Touch anywhere on the screen to invoke button controls. Figure 5. Main Menu (Page 1)) Page 1 of main menu is accessed by pressing the “PAGE ½” button. -
Page 8: Figure 7. Supply Setup Screen
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11.4 Supply Setup 11.6 System Setup Figure 7. Supply Setup Screen Figure 9. System Setup Screen Available setup: Available setup: Pump name - Configures pump name. Max of 15 characters. -
Page 9: Figure 10. Analog Output Screen
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11.7 Analog Output 11.8 Digital Input Setup Figure 11. Digital Input Setup Screen Figure 10. Analog Output Screen Total of four digital inputs on connector J104. Total of four analog outputs on connector J104:... -
Page 10: Figure 12. Digital Output Setup Screen
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11.9 Digital Output 11.10 Relay Setup Figure 13. Relay Setup Screen Figure 12. Digital Output Setup Screen Total of four relays on connector J104: Total of four digital outputs on connector J104:... -
Page 11: Figure 14. Serial Port Setup Screen
Figure 14. Serial Port Setup Screen Figure 16. Ethernet Setup Screen Available setup: Avalable setup: Node Address - Configures unit node address (1-255). Gamma MAC address - Information only. Ethernet MAC address. Cannot be protocol command packet structure requires node address. changed. -
Page 12: Figure 17. Tsp Sublimation View Screen (No Control Buttons)
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11.14 TSP Sublimation View 11.15 TSP Sublimation View With Controls Figure 18. TSP Sublimation View Screen With Controls Figure 17. TSP Sublimation View Screen (no control buttons) View Pump - Switches home screen to pump view. -
Page 13: Figure 19. Tsp Setup Screen
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 11.16 TSP Setup 11.17 TSP Pressure Window Setup Figure 19. TSP Setup Screen Figure 20. TSP Pressure Window Screen Available setup : Available setup : Filament - Selects active filament (1-4). -
Page 14: Error / Status Codes
Pump size set to 0L/s. HV cannot run. Supply not calibrated. Current metering might not be accurate. Supply over-temperature detected. HV cannot run. NOTE: If error code is not listed in the table please contact Gamma Vacuum for more information. Page 14 of 28... -
Page 15: Rear Panel
Use high current cable to connect to Titatium Sublimation Pump Standard Sub-D 9-pin female connector. Connection to Profibus (TSP). interface. For Profibus information reference Profibus user manual, document 900033, available on Gamma Vacuum website under download section. Page 15 of 28... -
Page 16: Table 2. J104 Connector Pinout
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 13.7 Connector J104, Misc I/O 13.8 Connector J112, SER Standard Sub-D 9-pin female connector. Connection to serial Standard Sub-D 37-pin female connector. interface. Supported serial standars are RS-232, RS-485 full duplex Table 2. -
Page 17: Serial Communication
2 ASCII hex characters Range 00 through FF See “Table 9. Gamma Protocol Commands” on page 20 for list of available command codes. The command code must be two hex digits, even if the first is a zero. 4. DATA field(s) -
Page 18: Table 5. Response Packet Structure Over Serial Connection
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 14.2 Gamma Protocol Response Packet Structure Over Serial Connection The response packet is made up of at least five fields and contains information to let the controlling computer know the command requested was either recognized and accepted (STATUS = “OK”), or an error condition occurred (STATUS = “ER”). -
Page 19: Table 7. Command Crc Checksum
Rx – “01 OK 00 1.0E-11 TORR A5” + carriage return Example 1 Command - SYS GET MODEL, 0x01 Tx – “~ 01 01 22” + carriage return. Rx – “01 OK 00 DIGITEL MPCQ 2E” + carriage return Page 19 of 28... -
Page 20: Table 9. Gamma Protocol Commands
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 14.5 Gamma Protocol Commands Table 9. Gamma Protocol Commands 9.1 Hex 9.2 Description 9.3 Data 9.4 Response 9.5 Data/Response Command Field Description SYS GET MODEL DIGITEL MPCQ Get controller model string. - Page 21 Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 9.1 Hex 9.2 Description 9.3 Data 9.4 Response 9.5 Data/Response Command Field Description HV SET SUPPLY AUTO RESTART S, X Where: S is supply (1-2) Sets supply auto restart option.
- Page 22 Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 9.1 Hex 9.2 Description 9.3 Data 9.4 Response 9.5 Data/Response Command Field Description TSP TURN ON Where: R is TSP (1-2) Turns on TSP programmed mode. TSP GET ACTIVE FILAMENT Where: Reads active TSP filament.
- Page 23 Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 9.1 Hex 9.2 Description 9.3 Data 9.4 Response 9.5 Data/Response Command Field Description TSP GET TSP STATUS R, X Where: Reads TSP status. R is TSP (1-2) X is option. Currently option 0 is only supported.
-
Page 24: Ethernet Communication
2 ASCII hex characters Range 00 through FF See “Table 9. Gamma Protocol Commands” on page 20 for list of available command codes. The command code must be two hex digits, even if the first digit is a zero. 4. DATA... -
Page 25: Technical Specifications
Gamma Vacuum DIGITEL MPCq Users Manual Document 900034, Rev B 17. TECHNICAL SPECIFICATIONS Dimensions (max) ......472 x 432 x 131mm, length x width x height (fits standard 19 inch wide device rack) Shipping Weight (max) ....32 (66) kg lbs (fully configured with two supplies) Operating Temperature ....0 to 40C Free airflow around the unit is required. -
Page 26: Warranty & Service
Gamma Vacuum agrees to either repair or replace, at abrasive cloth will ensure no damage to the LCD screen and finish of Gamma Vacuum’s option and free of parts charge to Buyer, and part the unit. or parts which, under proper and normal conditions of use, prove... - Page 27 Upon notification, Gamma Vacuum will investigate Warranty Claims. To initiate a Warranty Claim, please contact Gamma Vacuum or a representative of Gamma Vacuum directly. To assist in this evaluation, please provide the following information in as much detail as possible: •...
-
Page 28: Return Material Authorization Form
RETURN MATERIAL AUTHORIZATION FORM Thank you for taking the time to complete this form. Please complete this form and return to Gamma Vacuum in electronic format (Adobe PDF format (.pdf) preferred), or via fax. Digital signatures are acceptable Assigned RMA:...