Table of Contents
Advertisement
Quick Links
Content
CONTENTS
th
1217 E. 7
St.
Mishawaka, IN 46544
www.powergearus.com
© Copyright LCI/PowerGear Issued: December 2014
Owner's Manual Dual Planetary
Introduction
SYSTEM DESCRIPTION:
1
2
The Power Gear In Wall Slideout System is a rack and pinion design
2
operated by a 12 Volt DC electric Motor. The system is designed to move a
3
3
room of no more than 1500 pounds, with a 30" stroke. Room slide out
4-6
systems rated for higher weight or longer strokes can be obtained. Please
7
contact Power Gear for application assistance.
7
MAJOR COMPONENTS:
•
Vertical channel that mounts into the side wall opening.
•
Horizontal gear rack arms that actuate the room.
•
A 12 Volt DC gear motor will operate the room using power from the
battery.
•
Slideout Systems are equipped with a manual override that allows you
to extend/retract the room in the event of a loss of power.
•
A specially designed control that gives the user full control of room
movement, in or out. The control has programmable stops that stop the
motor when the room is fully extended or retracted and the ability to
detect faults for ease in troubleshooting.
•
Touchpad that mounts to the wall. It allows room movement and
provides end user feedback.
•
Floor rollers (not supplied by Power Gear)
Owner's Manual Slim Rack In
Wall Slide Out System
Control Box Part Number
Gearmotor Slim Rack
Slide Out System
1510000199
#3010002679, Rev. 0C
Page 1 of 7
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Power Gear 1510000199
Summary of Contents for Power Gear 1510000199
- Page 1 CONTENTS Introduction SYSTEM DESCRIPTION: Introduction Operation Mode The Power Gear In Wall Slideout System is a rack and pinion design Preventative Maintenance operated by a 12 Volt DC electric Motor. The system is designed to move a Fault Diagnostics Troubleshooting room of no more than 1500 pounds, with a 30”...
- Page 2 If equipped, turn “off” the on/off switch or key. If equipped, install the transit bars. Preventative Maintenance Your Power Gear slideout system has been designed to require very little maintenance. To ensure the long life of your slideout system, read and follow these few simple procedures: •...
- Page 3 3010002679 Rev 0C Owner’s Manual In Wall Slide Out System Fault Diagnostics/Troubleshooting WARNING This control has the ability to detect and display several faults. When a fault is detected, the room movement will stop and two (2) different LED’s will flash in a pattern. •...
- Page 4 3010002679 Rev 0C Owner’s Manual In Wall Slide Out System Override Modes WARNING In the event of component failure or loss of system power, your slideout can be manually overridden and retracted for travel. • Always make sure that the Note: At any time during the override procedure, the unit will exit this mode if the room has slideout room path is clear not been moved for two (2) minutes or if a fault is detected during room movement.
- Page 5 3010002679 Rev 0C Owner’s Manual In Wall Slide Out System Override Modes (continued) WARNING MANUAL EMERGENCY RETRACT MODE Use this procedure when the above procedures do not work. • Always make sure that the In the event that power is lost to the slide out motor(s) or OVERRIDE MODE A (page 4) will not slideout room path is clear work, the room can be manually retracted by following these steps: of people and objects...
- Page 6 3010002679 Rev 0C Owner’s Manual In Wall Slide Out System Override Modes (continued) Note: It may also be possible to manually retract the room by using a ratchet and socket attached to the end of the coupler (FIGURE 11). You will first need to follow steps 1-6 under the Manual Retract Mode section to remove the motor.
- Page 7 Power Gear reserves the right to change the terms of our warranty policy at any time. For the most current information on product warranty and our warranty claim procedure, visit our website at www.powergearus.com.
Need help?
Do you have a question about the 1510000199 and is the answer not in the manual?
Questions and answers