Valterra Products TireMinder TMG-AAA-IR Instruction Manual

TireMinder® TMG-AAA-IR – Instruction Manual
Thank you for the purchase of your new TireMinder® Infrared Thermometer. Please see the instructions below to safety operate this unit.
IMPORTANT SAFETY INFORMATION
WARNING: Read all instructions before operating product. Failure to follow all
instructions may result in serious injury.
1. Before using this unit, confirm that the plastic housing is intact and shows
no sign of damage. If there is any damage, do not use the thermometer
and return to the place of purchase.
2. Do not point the laser toward anyone's eye or at reflective surfaces.
3. Do not use this unit near steam, dusty environments, explosive gas, or
any other potentially explosive chemicals.
CAUTION
To avoid damage to the unit or target, avoid the following situations:
1. EMF (electro-magnetic fields) from arc welders, induction heaters, etc.
2. Thermal shock, caused by large or abrupt ambient temperature
changes. Allow 30 minutes for unit to stabilize, prior to use.
3. Storage - Do not leave the unit on or near objects with a temperature of
140°F (60°C) or higher.
Distance to Spot Size (or Ratio)
When taking a measurement, be aware of the Distance to Spot Size. As the
Distance (D) from the target surface increases, the Spot Size (S), the area
measured by the unit, becomes larger (See Figure 1).
Confirm that the target is larger than the unit's spot size. The smaller the target,
the closer the measurement distance needs to be. When accuracy is critical,
make sure the target is at least twice as large as the spot size.
Emissivity
Most organic material, as well as painted or oxidized surfaces, have an
emissivity of 0.95 (preset in the unit). Inaccurate readings will result from
measuring shiny or polished metal surfaces. To compensate, cover the target
surface with masking tape or flat black paint. Measure the tape or painted
surface once the tape or paint reach the same temperature as the material
underneath.
Operation (Figure 2)
1. Open the battery door, which is located at the top
of the grip, and insert 2 "AAA" batteries (included).
2. Pull the trigger to turn on the unit.
3. Aim at the target surface and pull the trigger. As
the trigger is being held, the temperature will be
displayed on the LCD. Once the trigger is released,
the temperature will be held on the display for
approximately 7 seconds.
4. Note, this unit is equipped with a laster, which is
only used for aiming.
Locating a Hot Spot
To find a hot spot, aim the thermometer outside of the point of interest, then
scan across with an up and down motion, until the hot spot is located (see
Figure 3).
LCD Display Key (Figure 4)
a. Data Hold Icon
b. Scanning Icon
c. Laser On Icon
d. Backlight On Icon
e. Low Battery Icon
f. Fahrenheit
g. Celsius
h. Temperature Reading
Button Key (Figure 5)
1. Trigger
2. Laser On/Off
3. °F/°C Toggle
4. Backlight On/Off
Maintenance
Clean the lens periodically using clean, compress air. Gently brush remaining
debris with a moist cotton swap. The swab may be moistened with water.
To clean the case, wipe the case with a damp sponge or cloth and mild soap.
Specifications
Temperature Range -58~716°F (-50~380°C)
32~716°F (0~380°C) - ±2.7°F (±1.5°C) or ±1.5%
Accuracy -58~32°F (-50~0°C) - ±5°F (±3°C) or ±1.5%
Whichever is greater
Resolution 0.1°C or 0.1°F
Repeatability 1% of reading or 1°C
Response Time 500ms, 95% response
Spectral Response 5-14um
Emissivity 0.95 Preset
Distance to Spot Size 12:1
Storage Temperature -4~140°F (-20~60°C)
Power 2 "AAA" Batteries (1.5V)
Typical Battery Life 6 to 12 hours of usage
Model Number TM22290VP
Support +1 (772) 463-6522 | www.MinderResearch.com
Warranty 1 Year Warranty
Minder Division of Valterra Products, LLC. holds no responsibility from the use of this product.
We reserve the right to modify the product design and specifications without notice.
©2019 Valterra Products, LLC
.