Table of Contents
Advertisement
Quick Links
2019-4029
2019-11-13
Cell SANICLEAR40
READ THE LABEL AND OPERATION AND INSTALLATION MANUAL of the "SANICLEAR40 system" thoroughly
before the installation or usage of this replacement cell.
Replacement Cell for the SANICLEARSANICLEAR system (Canada)
REGISTRATION N° (30794) PEST CONTROL PRODUCTS ACT
This cell must only be used with this model of SANICLEAR40 system.
Tel.: +1. 450.250.4500 • Fax: +1.450.250.4501
Support: 1.866.979.4501
CARVIN POOL EQUIPMENT
4000 Boul. Casavant Ouest – Saint‐Hyacinthe (Québec) Canada J2S 9E3
www.carvinpool.com
1
M10083
Advertisement
Table of Contents
Related Manuals for CARVIN SANICLEAR40
Summary of Contents for CARVIN SANICLEAR40
- Page 1 2019-4029 2019-11-13 Cell SANICLEAR40 READ THE LABEL AND OPERATION AND INSTALLATION MANUAL of the “SANICLEAR40 system” thoroughly before the installation or usage of this replacement cell. Replacement Cell for the SANICLEARSANICLEAR system (Canada) REGISTRATION N° (30794) PEST CONTROL PRODUCTS ACT This cell must only be used with this model of SANICLEAR40 system.
- Page 2 READ THIS LABEL AND OPERATION AND INSTALLATION MANUAL BEFORE USING. PRECAUTION: A maximum of 170,000 Litres (45,000 Gallons) of water can be treated with one Cell SANICLEAR40 Chlorine generator system unit. WARNING Operating the SANICLEARSANICLEAR system without water flow through the SANICLEARSANICLEAR system cell can cause a build‐up of flammable gases which can result in fire or explosion.
- Page 3 Power: 110 à 130 V CA, 2A, 50/60Hz or 220 à 250 V CA, 1A, 50/60Hz Timer: Connect to load side. Remote Control unit: Connect to line power SUITABLE FOR INDOOR OR OUTDOOR MOUNTING Imported by: CARVIN POOL EQUIPMENT 4000 Boul. Casavant Ouest – Saint‐Hyacinthe (Québec) Canada J2S 9E3 www.carvinpool.com LED Indicator...
- Page 4 CARVIN POOL EQUIPMENT Inc. 4000 Boul. Casavant Ouest – Saint-Hyacinthe (Québec) Canada J2S 9E3 Tel.: 1.450.250.4500 • Fax: 1.450.250.4501 Support: 1.866.979.4501 www.carvinpool.com M10077EN...
- Page 5 SANICLEAR For pools and hot tubs SANICLEAR Chlorine Generator system SANICLEAR40 In pools and hot tubs CONTROLS THE LEVEL OF BACTERIA AND ALGAE DOMESTIC OPERATION AND INSTALLATION MANUAL REGISTRATION NUMBER 30794 PEST CONTROL PRODUCTS ACT WARNING: Operating the SANICLEAR Chlorine generator system without any water flow through the cell can cause a build‐up of flammable gases which can result in...
-
Page 6: Table Of Contents
CONTENTS IMPORTANT SAFETY INSTRUCTION ……. 23 INSTALLATION ....24 Flow switch ............. 24 Cell… ..............25 Electrical warning… ..........26 Electrical information… ........... 26 WATER PREPARATION ........28 Ideal chemical Level… ..........28 Recommended salt… ..........28 Level of salt… ............29 Procedure for adding or remove salt…... -
Page 7: Important Safety Instruction
WARNING for Spa owner: this product is not recommended for acrylic or any other type of plastic spa. The use of this Chlorine Generator with this type of spa may void the Hot tubs manufacturer’s warranty. Carvin Pool Equipment will not be held responsible of this warranty if the user uses this product with acrylic or plastic spa. See with your dealer if this product is recommended for your application. -
Page 8: Installation
INSTALLATION Installation must be performed in accordance with all Local NEC codes. Preparing the Pool Water: Check the pool water chemistry and balance BEFORE activating the salt chlorinator. It is recommended that you consult a pool professional for the initial water balancing each season. NOTE: At the beginning of each season, add metal remover and polymer based (non copper) algaecide to the pool, as per the manufacturer’s instructions. - Page 9 Use the unions provided and tighten by hand at both ends of the cell for a perfect watertight seal. For pool or spa with spillover systems, use the fig #2 or #3 below to allow that chlorination is functional for both the pool and spa during spillover but when using the spa only it will prevent over chlorination.
-
Page 10: Electrical Warning
DANGER: RISK OF ELECTRIC SHOCK THAT CAN RESULT IN SERIOUS INJURY OR DEATH. Before proceeding with any wiring, the power at the circuit breaker must be turned off. Make sure to follow all electrical codes (local and NEC). For safe operation, the Salt chlorinator must be installed properly by being grounded and bonded. - Page 11 At the bottom of the Salt chlorinator there is a connection that should be used to ground the unit to the pool grounding system with a copper wire of 8 AWG (6 AWG for Canada) (as per diagram below) Installation of the cell and flow switch: The switches (electrolytic cell and flow switch) cables have connectors at the ends that plug into the salt chlorinator to facilitate installation.
-
Page 12: Cell
Combined Chlorine (Chloramines): None (super chlorinate to remove all chloramines) PH: 7.2 – 7.8 (USE MURIATIC ACID to lower PH and Soda Ash to raise PH.) Cyanuric Acid: 30 – 100 ppm (Carvin recommend 80ppm Total Alkalinity: 100 – 120 ppm Calcium Hardness: 200 –... -
Page 13: Level Of Salt
RECOMMENDED LEVEL OF SALT To determine how much salt will be needed, use the chart. Most pools contain some salt, depending on the water source and chemicals used for sanitizing. Therefore, the pool owner must always test salt levels before adding salt. -
Page 14: Chart For Salt Requirement
SALT REQUIREMENTS (POUNDS or Kg) FOR IDEAL CONDITION (3200 PPM) Current Gallons (Liters) of your pool water salt level 6,000 8,000 10,000 12,000 14,000 16,000 18,000 (22,500) (30,000) (37,500) (45,000) (52,500) (60,000) (67,500) 160 lbs 213 lbs 320 lbs 427 lbs 480 lbs 267lbs 373 lbs... -
Page 15: Other Chemical Requirements
STABILIZER (CYANURIC ACID) When testing for salt, also test for stabilizer level (cyanuric acid) this test should be done at least once per month. To know how much stabilizer is required to raise the level to 80 ppm, use the chart below. REQUIREMENTS IN POUNDS (kilogram) OF STABILISER FOR IDEAL CONDITION (80 PPM) Gallons (Liters) of your pool water... -
Page 16: Operation
OPERATION The SANICLEAR chlorine generation system is an automatic machine for pool & spa sanitation. The operation requires a low concentration of salt (sodium chloride) in the pool water at levels low enough that it normally cannot be tasted. It automatically sanitizes your pool by converting the salt into free chlorine, which kills bacteria and algae in the pool through a process called electrolysis. -
Page 17: Led Status
LED Status POWER, The salt chlorinator has input power when light is illuminated GENERATING: This LED light is on during normal operation cycle. When it is flashing, the pool water is either too hot or too cold for the system to operate. SUPER CHLORINATE: Light is illuminated during the super chlorination mode. -
Page 18: Display Screen
DISPLAY SCREEN The display screen shows the current salt concentration of the pool water. Readings are in ppm (parts per million). If you prefer metric reading for metric units (grams per liter), push the “diagnostic” button next to the display once. The display will now show the pool water temperature in degrees Fahrenheit. With the temperature displayed, move the main switch from AUTO to SUPER CHLORINATE to AUTO. -
Page 19: Servicing And Cleaning The Cell
SERVICING AND CLEANING THE CELL Turn off the power on the salt chlorinator before removing the cell. Once it is removed, look for debris inside the cell located on the plates Clean the plates thoroughly by using a high-pressure hose or any plastic scraper to scrape all deposits. -
Page 20: Troubleshooting
TROUBLESHOOTING Problems and Solutions The “Power” LED light is OFF Verify the 20 amp ATO fuse located in the circuit board above the cell connector. Check to make sure the power is connected to the control. Be sure the jumpers are set properly. Verify the voltage with a voltmeter and if the input power is functional the problem could be that the fuse is blown. - Page 21 "High Salt" LED light illuminated When illuminated, check the salt level in the pool or spa water. If the salt level is elevate (above 5000 ppm for SANICLEAR 40, above 7000 ppm for model SANICLEAR 40）, lower the level by draining part of the pool water and replace with some new fresh water.
-
Page 22: Limited Warranty
Mail-in the Warranty Registration Card. Online at www.carvinpool.com All defects must be denounced to “Carvin” or to their representative within 72 hours in order to avoid the spreading to other equipment, failing which; the present warranty will not be honoured. This warranty is non- transferable and extends only to the original retail buyer and only during the time in which the original retail buyer occupies the site where the product was originally installed. - Page 23 Warranty claims shall be made by contacting the installer/seller, builder, dealer, or retailer (point of purchase) or the "Carvin" pool products distributor in your area. All equipment must be inspected by a local "Carvin" authorized representative or at the factory before warranty is authorized. All charges or expenses for freight to and from the factory, removal and reinstallation of the products, or installation of a replacement product are the responsibility of the purchaser unless otherwise expressly authorized in writing by "Carvin".
-
Page 24: Replacement Part List
• When replacing the SANICLEAR Chlorine Generator System cell. Only use replacement cells having a label that clearly states that it is a replacement cell for the SANICLEAR Chlorine Generator System. REGISTRATION NUMBER 30794, PEST CONTROL PRODUCTS ACT. • The life expectancy of the SANICLEAR Chlorine Generator System cell is 10.000 hours under normal use conditions.
Need help?
Do you have a question about the SANICLEAR40 and is the answer not in the manual?
Questions and answers