Table of Contents
Advertisement
Quick Links
PROGRAMMABLE ELECTRIC TOWEL RAIL
MYBWF05ET & MYBWF08ET
BEFORE USE:
Please read the instructions carefully. You must inspect the appliance including its
cable and plug for any signs of damage. If the product is damaged, DO NOT USE
and contact your supplier immediately for refund, replacement or advice.
This product is only suitable for well insulated spaces or occasional use
Advertisement
Table of Contents
Summary of Contents for Mylek MYBWF05ET
- Page 1 PROGRAMMABLE ELECTRIC TOWEL RAIL MYBWF05ET & MYBWF08ET BEFORE USE: Please read the instructions carefully. You must inspect the appliance including its cable and plug for any signs of damage. If the product is damaged, DO NOT USE and contact your supplier immediately for refund, replacement or advice.
-
Page 2: Safety Instructions
BEFORE USING THIS HEATER: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons. This includes but is not limited to the following: CAUTION: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge of the product. - Page 3 • Check item carefully before use. Do not switch on heater with defects or damaged power cable. • The appliance should be connected to the same voltage as shown on the rating label and printed in the manual. • The heater should only be plugged into grounded sockets. •...
- Page 4 • CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
- Page 5 • Do not use this heater in the immediate zones surroundings of a bath, a shower or a swimming pool. Please use a qualified electrician to make sure the unit is installed in the correct zone in a bathroom. WARNING: •...
- Page 6 Zone 1: All circuits in this zone must be protected with a 30mA residual current device (RCD). It is good practice to use IPX5 in this zone. Zone 2: Appliance in this area must have a minimum IPX4 rating. Zone 3: This area must be outside of the water spray zones 0, I and 2.
-
Page 7: Installation
INSTALLATION: ≥ 150mm M4 x 6mm ≥ 150mm ≥ 150mm ≥ 600mm > 800mm... -
Page 8: Unit Description
Warning! Please choose correct installation area, always check to ensure there is no wiring, pipe work, etc. in the area to be drilled. A． Place the hanging rack on the wall as a guide ruler (please make sure the holes are at parallel level), use a pen to mark the hole positions B．... -
Page 9: Control Panel
Control Panel: 1. Standby indicator 2.Heating indicator 3. Comfort mode indicator 4. ECO mode indicator 5. LED display 6. Standby button 7. Mode button 8. Increase button 9. Decrease button 10. Timer button Operation The unit must be installed by a qualified electrician. Plug or Spur the appliance to AC 230V 50-60Hz socket. -
Page 10: Standard Heating Mode
Clock and day of week setting: Press 3 seconds to enter clock and day of week setting The screen display “d”, press to select the day from 1-7. Monday Tuesday Wednesday Thursday Friday Saturday Sunday Press to confirm day setting and the clock will show hour setting, the screen will display: h. - Page 11 Use of countdown timer: In standard heating ECO or Comfort mode you can leave the model on permanent or program the countdown timer so the unit turns off after your set hours have elapsed, press the button once and the “0h” will flash, using the key choose your set hour from 0-9 hours.
- Page 12 Figure 1 Program P2 • P2 (Figure 2) is a preset program Monday-Friday and Saturday -Sunday. See image below for P2 preset program which shows the unit settings in a 24hr period which will repeat over a 7 day period. (The images (Figure 2 and 3) below are just for illustration purposes only and not shown on the LED display.) P2:(Monday-Friday) preset program 00:00am –...
- Page 13 • Below are examples of what you can adjust P3 program to, although you can adjust this program to meet your own requirements. (Images (Figure 4 and 5) below are just for illustration purposes only and not shown on the LED display.) P3:(Monday-Friday) Adjustable program.
-
Page 14: Open Window Function
3. The screen displays for hour setting, press to choose either Comfort mode or ECO mode or press so neither the Comfort or ECO lights show so the heater will be in anti-frost mode. Press to move to the next hour to set or to the previous hour to set, choosing Comfort mode , ECO mode show no lights for the unit to operate in anti-frost mode in this hour, repeat this... -
Page 15: Pat Testing
PAT TESTING: When used in a workplace, this product must be safety-tested yearly by a qualified electrician (PAT Tested) in order to comply with the Electricity at Work Regulations. We recommend that it is PAT tested regularly when used in a domestic environment. OVERHEAT SAFETY DEVICE: Your heater is fitted with a safety device to switch off the heater in the event of overheating. - Page 16 Information requirement for the electric local space heaters Model identifier(s): MYBWF05ET Item Symbol Value Unit Item Unit Heat output Type of heat input, for electric storage local space heaters only (select one) Nominal heat output Pnom manual heat charge control, with integrated...
-
Page 17: Service / Warranty
YESSS Electrical, YESSS House, Normanton, WF6 1TN declares that the Mylek Heaters are exclusively manufactured and imported for Hygiene Supplies Direct Ltd...
Need help?
Do you have a question about the MYBWF05ET and is the answer not in the manual?
Questions and answers