Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DLI DLM-4 ZONE
Summary of Contents for DLI DLM-4 ZONE
- Page 1 DLM-4 ZONE Controller...
-
Page 2: Table Of Contents
BEFORE attempting to install of use this product, it is important to read and fully understand this instruction manual. It will provide The DLM-4 Zone Controller is specially designed to set up a Daily detailed instructions and guidelines that will help to set up the unit, Lighting Management system for your Dutch Lighting Innovations and to understand the full capability of this unit. -
Page 3: Facts
You cannot mix fixtures with different wattages on the same zone interconnect wiring. • A single low-volt cable is used to interconnect the DLM-4 ZONE to the fixtures within each zone. Various length pre-crimped RJ12 cables and additional interconnect splitters can be purchased separately. -
Page 4: Installing The Dlm-4 Zone Controller
5. Determining the Zones Controller Installation of the DLM-4 Zone Controller starts by first designing the DLI fixtures layout and the DLI fixtures will be connected to the controller. Each zone can have separate dimming actions to take Release /... -
Page 5: Connections
DLM-4 Zone Controller. connected to the DLM-4 Zone Controller unit. Each of the 4 available zones on the DLM-4 Zone Controller unit will have a separate cable connection to connect to the fixtures AVERTISSEMENT: NE branchez PAS l’alimentation sur les... - Page 6 All ballast and the temperature sensors should be connected to the zones before continuing the installation. Verify that all of the fixtures connected to the DLM-4 Zone Controller have been set to operate using the External control. Turn the selector switch on the side of each of the ballast to the correct position to allow the DLM-4 Zone Controller to control the ballast.
-
Page 7: Set-Up And Using Your Dlm-4 Zone Controller
MENU: The Menu button will change the display from one page to the If it is the first time you have used the DLM-4 Zone Controller, when next page within the menus. you power on the DLM-4 Zone Controller the Welcome screen / page... -
Page 8: Configuration Page
Zone 2 Zone 3 Zone 4 Override The DLM-4 Zone Controller unit has several configuration settings that can be customized by the user, those settings are stored in Configuration the Configuration page. Below is a description of the Configuration System Setup settings. -
Page 9: Zone Setting Page(S)
Stop at: The user can select the “maximum” temperature that the Each of the 4 zones within the DLM-4 Zone Controller has a separate growing area can get to before shutting down the lighting zones. This page for that zone’s particular settings. The settings are described setting should normally be set at least 5’F up to 10 degrees F above the... -
Page 10: Zone Status Page
7.5 Zone Status Page 7.6 Temperature Min-Max Page Pressing the Find button on the DLM-4 Zone Controller will access Once the DLM-4 Zone Controller has been installed and all settings some important functions. The first page that will be displayed is the have been entered, the DLM-4 Zone Controller will constantly monitor Temperature Minimum-Maximum page. -
Page 11: Manual Override (Force) Page
Occasionally the user may want to manually turn each lighting Zone When the OverRide menu is displayed, use the Up and Down On or Off manually. Each of the 4 zones within the DLM-4 ZONE buttons to move the cursor to the Zone # that you want to force controller can be manually activated (turned ON or OFF) by accessing On (or Off). -
Page 12: Factory Reset
To reset the setting to factory presetting, select the “System Setup” previous menu page in the Main menu and then select “Factory Reset” FACTORY RESET PAGE Pressing “Enter”, will reset the DLM-4 Zone Controller to the factory settings and automatically return to “System Setup” menu page. System Setup Factory Reset Firmware Update Firmware: V_2.7... -
Page 13: Firmware Update Page
7.10 Firmware Update Page Continued... Occasionally the DLM-4 Zone Controller may release updated firmware / software for the DLM-4 Zone Controller. The new firmware may update older versions firmware, or add new functions to the DLM- 4 Zone Controller. To update the firmware:... -
Page 14: Messages / Data Log
Move the cursor to the newest version of the firmware to be installed. The DLM-4 Zone Controller is constantly monitoring the power going to the DLM-4 Zone Controller. When power is re-applied to the DLM-4 Update code is Zone Controller, the unit will start up and display the Power Failure DIMMER error. -
Page 15: Hot-Start Prevention
15 minute time delay to allow the lamps to cool before re-starting. Each successive zone re-start will be preceded by a 5 second delay in The DLM-4 Zone Controller has the ability to monitor the temperature order to reduce electrical startup surges / loads. During the 15-minute of 4-separate zones. - Page 16 Components that are excluded from warranty are components that have failed due to abnormal usage. In the case of defects of the DLM-4 Zone Controller, the Controller will either be replaced or repaired using new or reconditioned products or parts. If the Controller will be replaced this limited warranty shall apply to the replacement product for the remaining initial warranty period, i.e.
- Page 17 PROBLEM RESOLUTION If the DLM-4 surface is dirty, wipe it with a dry towel. The DLM-4 operates under natural ventilation conditions. The DLM-4 Zone Controller is Check the low-volt power connected to power, but it supply is plugged in properly does not seem to be working to the DLM-4 Zone Controller.
- Page 18 DLM-4 ZONE DLM-4 ZONE Controller Controller ENVIRONMENTAL AND DISPOSAL CONCERNS: SPECIFICATIONS: THIS PRODUCT CONTAINS A BATTERY AND OTHER COMPONENTS 12vdc @ 200ma Voltage / power supply WHICH MUST BE DISPOSED OF PROPERLY. 12 V CC 200 mA Tension / Alimentation électrique...
- Page 19 www.dutchlightinginnovations.com...
Need help?
Do you have a question about the DLM-4 ZONE and is the answer not in the manual?
Questions and answers