Table of Contents
Advertisement
Quick Links
PROPRIETARY NOTICE
All rights reserved by Janz Tec AG.
No parts of this technical manual may be modified, copied or reproduced
in any form or by any means for commercial use without the prior written
permission of Janz Tec AG, Germany.
All instructions, information and specification contained in this manual
are for reference only and remain subject to change without
announcement.
emPC-CX+
embedded PC
(Hardware Manual)
Version 1.3
refers to product revision no.
-
Advertisement
Table of Contents
Summary of Contents for Janz Tec emPC-CX+/C-1047UE
- Page 1 PROPRIETARY NOTICE All rights reserved by Janz Tec AG. No parts of this technical manual may be modified, copied or reproduced in any form or by any means for commercial use without the prior written permission of Janz Tec AG, Germany.
- Page 2 Title: emPC-CX+ embedded PC File: j:\as\entwicklung\projekte\hw\empc\empc_+\doc\manual\manual_empc- cxplus_hardware.docx Pattern: c:\users\as\appdata\roaming\microsoft\templates\normal.dotm Created: Stefan Althöfer, 27.05.2021 Last Update: Stefan Althöfer, 06.07.2022 © Janz Tec AG 2021 Im Dörener Feld 8 D-33100 Paderborn, Germany Tel.: +49-5251-1550-0 FAX: +49-5251-1550-190 email: support@janztec.com Internet: www.janztec.com...
-
Page 3: Table Of Contents
CAN ..........................14 4.2.8 Digital IO ........................14 Maintenance Battery Replacement ......................17 PCI Express Mini Card .......................18 Installing PCI-Cards ......................18 SATA drives ........................19 Appendices Technical Data ........................20 References .........................27 Dimensions ........................28 Product History........................29 Manual History ........................30 Rev. 1.3 © Janz Tec AG... - Page 4 Table 1: Power connector pin assignment .....................12 table 2: DVI-D connector ........................12 table 3: Ethernet connector ........................13 table 4: USB connector ...........................13 table 5: RS232 connector ........................14 table 6: CAN connector ..........................14 table 7: digital IO connector ........................14 © Janz Tec AG Rev. 1.3...
- Page 5 There exist some isolated reference grounds for communication interfaces or IO. These reference signals are referred to as GND-x, where x indicates function. SELV Safety extra low voltage. Rev. 1.3 © Janz Tec AG...
-
Page 7: Introduction
One internal slot is available. Ask for customized connector panels with additional holes to be utilized by the Mini Card connectors. 1.1.2.3 Internal USB Two internal USB interfaces are available on 10 pin header, e.g. for integration of dongles. Rev. 1.3 © Janz Tec AG... -
Page 8: 1.1.2.4 Personality Board
DDI1 must support T.M.D.S (HDMI,DVI) • Sufficient PCIe lanes available 1.1.3 Software Supported by • Windows 7/8 • Windows 7/8 embedded • Linux Contact Janz Tec for more information about the available software packages. © Janz Tec AG Rev. 1.3... -
Page 9: Functional Overview
: Not available with some COM Express modules á Note: CX+/L is a stripped down version with P.-Board additional limitations. Refer to technical data for full details figure 1: block diagram (with 4 slot riser card shown) Rev. 1.3 © Janz Tec AG... -
Page 10: Safety Instructions
DANGER: Explosive Risk Do not operate the product in potentially explosive atmosphere. NOTICE: EMI This product is a class A device. This product may cause radio interference. In this case the user must take adequate measures. © Janz Tec AG Rev. 1.3... -
Page 11: Intended Use
Janz Tec electronic products are labelled with the crossed-out trash can. This means that the products must not be disposed into the domestic garbage. Used Janz Tec products have to be recycled properly. If in doubt, you can return them to Janz Tec at your own expense. Refer to https://www.janztec.com/recycling or contact Janz Tec under recycling@janztec.com for more instructions how and where to return the products. -
Page 12: Installation
(e.g. 14 to 34 V). Mounting The emPC-CX+ is intended for wall mount. Refer to figure 2 for the recommended mounting orientation. Top Cover figure 2: emPC-CX+ mounting options © Janz Tec AG Rev. 1.3... -
Page 13: Connectors And Operators
(Hardware Manual) • Installation 4 - 11 Connectors and Operators figure 3: emPC-CX+ connector panel Rev. 1.3 © Janz Tec AG... -
Page 14: Power In
Ethernet Interfaces (LAN1 and LAN2) Ethernet interfaces of the motherboard. The Ethernet physics is 10/100/1000BaseT, available through the shielded modular jack at the connector panel. Twisted pair cable can be used to connect to this port. © Janz Tec AG Rev. 1.3... -
Page 15: Usb Type A Receptacle (Usb1-Usb4)
The cFAST memory card is accessible after removing the cover on the connector panel of system. Push the ejector button to remove. CFast Figure 5: CFast slot cover NOTICE The CFast card must NOT be inserted or removed when power is applied to the Rev. 1.3 © Janz Tec AG... -
Page 16: Rs232 Connector
Mating connectors with spring-cage connection are also available. Digital output pins drive VIN-DIO to the output pins (high side switch). See figure 6 for details. This signal is optionally available to provide power to supply an external transceiver module © Janz Tec AG Rev. 1.3... -
Page 17: Figure 6: Digital Input /Output Structure
Each port pin (DIGOUT-0…DIGOUT-3) is able to source 500mA into a load. The sum of all output currents should be limited to 1A. Systems without the digital IO option have the connector mounted, with all contacts not connected to any logic. Refer to technical data for characteristics. Rev. 1.3 © Janz Tec AG... -
Page 18: Maintenance
Replace SSD/HDD remove Replace FAN remove Replace Battery remove PCI cards must be removed Replace PCIe mini card remove PCI cards must be removed Replace CFast Only remove CFast cover from mouting panel © Janz Tec AG Rev. 1.3... -
Page 19: Battery Replacement
2. Insertion: Align new battery to the left side of the holder and gently press down on the right side of the battery until the battery snaps into the holder. figure 7: Removing and replacing coin cell battery Rev. 1.3 © Janz Tec AG... -
Page 20: Pci Express Mini Card
This causes the system to overheat and a damage of the systems is possible. If high power PCI cards are used a system fan is recommended. Contact the Janz Tec AG for further information. Before installing a PCI card, please make sure that the system is turned off. To get access to the PCI slot, the top cover must be removed. -
Page 21: Sata Drives
Please be careful when opening the top cover, because the optionally mounted drive cable is connected. Therefore, the top cover can’t be removed completely without disconnecting. Figure 8: Drive mounting for 0 slot systems Figure 9: Disk mounting for 2+ slot systems Rev. 1.3 © Janz Tec AG... -
Page 22: Appendices
1 x Green LED for power supply status 1 x Yellow LED for SATA activity User LEDs 4 x User programmable LEDs (2 x red, 2 x green) System Housing galvanized steel sheet, outside painted © Janz Tec AG Rev. 1.3... - Page 23 96 x 171 x 230 mm 2 Slot (2P/2X): 147 x 171 x 230 mm 4 Slot (4P/4X): 179 x 171 x 230 mm Weight 0 Slot: 2.4 kg 2 Slot (2P/2X): 2.8 kg 4 Slot (4P/4X): Rev. 1.3 © Janz Tec AG...
- Page 24 Spartan 6 LX25T, PCI express interface to baseboard IOs Expansion PCI Express 1 x PCI Express Mini Card slot Riser cards connector with 2 x PCIe x1 Personality Board with HDA and FPGA IOs 2 x USB2.0, internal connector © Janz Tec AG Rev. 1.3...
- Page 25 96 x 171 x 230 mm 2 Slot (2P/2X): 147 x 171 x 230 mm 4 Slot (4P/4X): 179 x 171 x 230 mm Weight 0 Slot: 2.4 kg 2 Slot (2P/2X): 2.8 kg 4 Slot (4P/4X): Rev. 1.3 © Janz Tec AG...
- Page 26 Riser cards connector with 2 x PCIe x1 Personality Board with HDA and FPGA IOs 2 x USB2.0, internal connector Power Requirements Power Supply DC power, 9 .. 34 V (lower limit with adjustable UVL) © Janz Tec AG Rev. 1.3...
- Page 27 The inrush current is not controlled in this case. Rise time of external power supply should be limited to below 5 V/ms. Max. CPU-frequency 2 GHz Max. CPU-frequency 3.6 GHz Thermal Design Power [W] Rev. 1.3 © Janz Tec AG...
- Page 28 Customers wishing to use this features should study the VN330SP datasheet very carefully and test their application. It is likely that the switching frequency has to be reduced to reduce dispassion of clamping energy. © Janz Tec AG Rev. 1.3...
-
Page 29: References
These references direct you to manuals and specifications that you might need to know when you attempt to program the product. Most of the documents can be downloaded from the Internet. Look for the WWW servers of the component/chip manufacturers. WWW-References Janz Tec AG www.janztec.com Intel Corporation www.intel.com Rev. 1.3 © Janz Tec AG... -
Page 30: Dimensions
W = 96,0 mm 26,4 mm 118,0 mm figure 10: housing dimensions (0 slot system shown) emPC-CX+ Systems with PCI Slots just differ in dimension W Slot Variant 96 mm 2P/2X 147 mm 4P/4X 179 mm © Janz Tec AG Rev. 1.3... -
Page 31: Product History
(Hardware Manual) • Appendices 6 - 29 Product History Rev. 1.3 © Janz Tec AG... -
Page 32: Manual History
• Added warning about use of power connector • Added specifications for digital IO V1.2 2021-05-27 Heje • Improved polarity indication of power and digital IO connectors • Added emPC-CX+/Ryzen/V1404I • Added chapter 3 (intended use) V1.3 2022-06-07 © Janz Tec AG Rev. 1.3...