Summary of Contents for Milenco MYCOOLMAN CEP 47
- Page 1 COMPRESSOR FRIDGE·FREEZER Operation Manual for AC/DC Fridge ·Freezer Model CEP 47 www.mycoolman.co.uk www.mycoolman.com LEISURE-TEC International Ltd...
-
Page 2: Intended Use
COMPRESSOR FRIDGE·FREEZER Contents Intended Use Page Important Safety Warnings Page Important Product Information Page Product Features Page LED Control Panel & Operation Instructions page 4-5 Handle Fitting Instructions Page Two Way Opening and Removable Lid Page Emergency Override Page Cleaning & Maintenance Page Troubleshooting Page... -
Page 3: Important Product Information
COMPRESSOR FRIDGE·FREEZER Important Product Information • Best performance is achieved in ambient • Make sure the voltage is within the correct temperatures between +10 °C and + 43 °C. range for socket and cable being used. • Temperatures above +32 °C may see a slight per- •... - Page 4 COMPRESSOR FRIDGE·FREEZER LED Control Panel & Operation Instructions Control Panel CEP 47 Power/Status Power Switch Indicator Light LED-Display Temperature Settings Turbo Switch Turbo Indicator Light NOTE: Temperature can be set from –18 ºC to +10 ºC Turning the unit on and off: Step 1: Plug in the AC or DC power cable (ensure power is on at source).
- Page 5 COMPRESSOR FRIDGE·FREEZER LED Control Panel & Operation Instructions Engaging Turbo mode: What is the purpose of Turbo Mode? It enables the compressor to run at a higher speed, therefore achieving faster cooling to your nominated temperature. Step 1: Press the button once to turn on.
- Page 6 COMPRESSOR FRIDGE·FREEZER Handle Fitting Instructions In your myCOOLMAN CEP 47 you will receive handle kit. Contents: 1. 2 x handle assemblies (complete) 2. 8 x Hex Head SS set screws 3. 1 x 5 mm Hex tool (Allen key) Assembly process:...
- Page 7 COMPRESSOR FRIDGE·FREEZER Two Way Opening and Removable Lid Purpose for removing the lid: CEP 47 This lid can be removed to aid with cleaning and to change the opening direction. You can change the direction of the lid by following the below instructions. How to remove the lid: Open the lid fully, then overextend, pushing lid past the “fully open point”...
-
Page 8: Emergency Override
COMPRESSOR FRIDGE·FREEZER Emergency Override Fuse 6.3A The Emergency Override Switch is NOTE: located just below the main control • In EMERGENCY OVERRIDE, the cooler runs panel next to the power inlets with full cooling capacity (i.e. will chill as heavily as possible with no regard to the For normal operation the switch is in the set temperature) and may freeze. -
Page 9: Troubleshooting
Unusual noise when refrigerator is working • The refrigerator is not placed on a level surface. If none of the above solves your issue, see page 3 or contact Milenco Ltd on the hotline for your location. UK: 01908 220102 or US: 574-208-9812 NOTE: At inclinations of more than 15 °... -
Page 10: Status Indicator
Status Indicator E0 flash every 4 seconds temperature sensor issue: • Contact Milenco Ltd on the hotline for your location UK: 01908 220102 or US: 574-208-9812 E1 flash every 4 seconds - low voltage & Battery Protection: • An E1 will occur when the battery protection level has been reached. - Page 11 COMPRESSOR FRIDGE·FREEZER Ideal Accessory: The myCOOLMAN Power Pack with magnetic fitting The myCOOLMAN Power Pack is now available as an ideal accessory to It can be attached to the front side of your operate your myCOOLMAN fridge/freezer fridge/freezer. Just pin it on and plug it in. independent of a power source.
-
Page 12: Product Specifications
Designed in Germany, made in China for MILENCO Limited Blackhill Drive · Wolverton Mill Milton Keynes www.mycoolman.co.uk...
Need help?
Do you have a question about the MYCOOLMAN CEP 47 and is the answer not in the manual?
Questions and answers